RADIO ANTENNA CORD (for Hatchback 3 Door) > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim) |
![]() |
Remove the 2 package tray trim suspenders.
Remove the 5 pieces of hook tape.
Disengage the 2 claws and remove the package tray trim.
| 3. REMOVE DECK BOARD SUB-ASSEMBLY (w/ Deck Board) |
![]() |
Release the 2 knobs and remove the deck board.
| 4. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Deck Board) |
![]() |
Remove the spare wheel cover.
| 5. REMOVE DECK FLOOR BOX RH (w/ Deck Board) |
![]() |
Release the 2 knobs and remove the deck floor box.
| 6. REMOVE DECK FLOOR BOX LH (w/ Deck Board) |
| 7. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Deck Board) |
![]() |
Remove the rear floor carpet.
| 8. REMOVE NO. 1 REAR SEAT LEG COVER |
for RH Side:
Remove the No. 1 rear seat leg cover .
for LH Side:
Remove the No. 1 rear seat leg cover .
| 9. REMOVE NO. 2 REAR SEAT LEG COVER |
![]() |
Disengage the 3 claws in the sequence shown in the illustration and remove the No. 1 rear seat leg cover.
| 10. REMOVE REAR SEAT ASSEMBLY RH |
![]() |
Using "TORX" socket wrench E10, remove the 2 bolts and pull up the rear seat cushion.
![]() |
Using "TORX" socket wrench E10, remove the 4 bolts and the rear seat.
| 11. REMOVE REAR SEAT ASSEMBLY LH |
![]() |
Using "TORX" socket wrench E10, remove the 3 bolts and pull up the rear seat cushion.
![]() |
Using "TORX" socket wrench E10, remove the 4 bolts and the rear seat.
| 12. REMOVE FRONT DOOR SCUFF PLATE RH |
![]() |
Disengage the 8 claws and remove the front door scuff plate.
| 13. REMOVE FRONT DOOR SCUFF PLATE LH |
| 14. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY RH |
![]() |
Disengage the 4 claws and remove the instrument panel under cover.
| 15. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH |
![]() |
Remove the 2 screws.
Disengage the 3 claws and remove the instrument panel under cover.
| 16. REMOVE COWL SIDE TRIM BOARD RH |
![]() |
Disengage the claw and the stud bolt and remove the cowl side trim board.
| 17. REMOVE COWL SIDE TRIM BOARD LH |
| 18. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Remove the front door opening trim weatherstrip.
| 19. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 20. REMOVE FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY RH (w/ Seat Belt Bar) |
![]() |
Remove the 2 bolts and the front seat outer belt bar.
| 21. REMOVE FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY LH (w/ Seat Belt Bar) |
| 22. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH |
![]() |
Remove the belt of the rear seat outer belt from the rear seat shoulder belt hanger.
![]() |
Disengage the 8 clips, the retainer and the 10 claws and remove the front quarter trim panel.
| 23. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH |
| 24. REMOVE REAR DECK TRIM COVER |
![]() |
for Temper Spare Tire:
Using a clip remover, remove the 2 clips.
Disengage the 8 claws and remove the rear deck trim cover.
![]() |
for Grand Tire:
Using a clip remover, remove the 2 clips.
Disengage the 8 claws and remove the rear deck trim cover.
| 25. REMOVE REAR SEAT OUTER BELT ASSEMBLY RH |
![]() |
Remove the bolt.
Disengage the clip and remove the anchor plate.
| 26. REMOVE REAR SEAT OUTER BELT ASSEMBLY LH |
| 27. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH |
![]() |
Remove the 3 screws.
Disengage the 3 clips and the 3 claws and remove the deck side trim panel.
| 28. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH |
![]() |
w/ Luggage Compartment Room Light:
Remove the 3 screws.
Disengage the 3 clips and the 3 claws.
Disconnect the deck side room light connector and remove the deck side trim panel.
w/o Luggage Compartment Room Light:
Remove the 3 screws.
Disengage the 3 clips and the 3 claws and remove the deck side trim panel.
| 29. REMOVE SEAT BELT ANCHOR COVER CAP |
![]() |
Disengage the 3 claws and remove the seat belt anchor cover cap.
| 30. REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH |
![]() |
Remove the bolt and the through anchor.
| 31. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH |
| 32. REMOVE CENTER PILLAR UPPER GARNISH RH |
![]() |
Disengage the 2 clips and remove the center pillar garnish.
| 33. REMOVE CENTER PILLAR UPPER GARNISH LH |
| 34. REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY (for 3 Point Type Rear Center Seat Belt) |
![]() |
Remove the 2 tongue plates.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and open the slip joint cover.
![]() |
Remove the bolt and the through anchor.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the center belt guide.
| 35. REMOVE ROOF SIDE INNER GARNISH RH |
![]() |
w/ Curtain Shield Airbag:
for 3 Point Type Rear Center Seat Belt:
for 2 Point Type Rear Center Seat Belt:
![]() |
w/o Curtain Shield Airbag:
for 3 Point Type Rear Center Seat Belt:
for 2 Point Type Rear Center Seat Belt:
| 36. REMOVE ROOF SIDE INNER GARNISH LH |
![]() |
w/ Curtain Shield Airbag:
Disengage the 4 clips and claw.
Pass the rear seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
![]() |
w/o Curtain Shield Airbag:
Disengage the 4 clips and claw.
Pass the rear seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
| 37. REMOVE REAR ROOF SIDE RAIL GARNISH RH |
![]() |
Disengage the 4 clips and remove the rear roof side rail garnish.
| 38. REMOVE REAR ROOF SIDE RAIL GARNISH LH |
| 39. REMOVE SEAT BELT ANCHOR COVER (for 3 Point Type Rear Center Seat Belt) |
![]() |
Using a moulding remover, disengage the 4 claws and remove the seat belt anchor cover.
| 40. REMOVE ROOF HEADLINING SERVICE HOLE COVER (w/o Curtain Shield Airbag) |
![]() |
Using a clip remover with its tip wrapped in protective tape, remove the 6 roof headlining service hole covers.
| 41. REMOVE COAT HOOK (w/ Coat Hook) |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and open the cover.
![]() |
Using a clip remover with its tip wrapped in protective tape, disengage the 2 claws and remove the coat hook.
| 42. REMOVE ASSIST GRIP SUB-ASSEMBLY |
![]() |
Disengage the 2 springs and remove the assist grip.
| 43. REMOVE VISOR ASSEMBLY RH |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the visor bracket cover.
![]() |
Remove the visor shaft from the visor holder.
Disengage the 2 springs and remove the visor.
| 44. REMOVE VISOR ASSEMBLY LH |
| 45. REMOVE VISOR HOLDER RH |
![]() |
Disengage the 2 claws by turning the visor counterclockwise between 60 to 120° and remove the visor holder.
| 46. REMOVE VISOR HOLDER LH |
| 47. REMOVE ROOM LIGHT ASSEMBLY |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light lens.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 covers.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws.
![]() |
Remove the roof wire from the claw of the room light.
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base and the room light.
| 48. REMOVE MAP LIGHT ASSEMBLY |
![]() |
Using a roof moulding remover, disengage the 4 claws.
![]() |
Disconnect the map light connector and remove the map light.
| 49. REMOVE FRONT PILLAR GARNISH RH |
![]() |
w/ Curtain Shield Airbag:
Disengage the 2 clips and the 2 claws and remove the front pillar garnish.
![]() |
w/o Curtain Shield Airbag:
Disengage the 2 clips and the 2 claws and remove the front pillar garnish.
![]() |
Disconnect the connector.
Using a clip remover, remove the 3 antenna cord clamps.
![]() |
w/ Front No. 2 Speaker:
Disconnect the speaker connector.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.
w/ Curtain Shield Airbag:
![]() |
Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
| Area | Measurement |
| a | 700 mm (27.56 in.) |
| b | 120 mm (4.72 in.) |
| 50. REMOVE FRONT PILLAR GARNISH LH |
![]() |
w/ Curtain Shield Airbag:
Disengage the 2 clips and the 2 claws and remove the front pillar garnish.
![]() |
w/o Curtain Shield Airbag:
Disengage the 2 clips and the 2 claws and remove the front pillar garnish.
![]() |
Using a clip remover, remove the 4 wire harness clamps.
![]() |
w/ Front No. 2 Speaker:
Disconnect the speaker connector.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.
![]() |
w/ Curtain Shield Airbag:
Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
| Area | Measurement |
| a | 700 mm (27.56 in.) |
| b | 120 mm (4.72 in.) |
| 51. REMOVE INSTRUMENT PANEL FINISH PANEL END LH |
![]() |
with CD player
Pull the instrument panel finish panel end LH rearward and disengage the 4 claws and 3 clips.
Disconnect the connector and remove the instrument panel finish panel end LH.
![]() |
Except CD player
Pull the instrument panel finish panel end LH rearward and disengage the 5 claws and 3 clips.
Disconnect the connector and remove the instrument panel finish panel end LH.
| 52. REMOVE INSTRUMENT PANEL FINISH PANEL END RH |
![]() |
with CD player
Pull the instrument panel finish panel end RH and disengage the 4 claws and 3 clips.
Disconnect the connector and remove the instrument panel finish panel end RH.
![]() |
Except CD player
Pull the instrument panel finish panel end RH rearward and disengage the 5 claws and 3 clips.
Disconnect the connector and remove the instrument panel finish panel end RH.
| 53. REMOVE INSTRUMENT CLUSTER FINISH PANEL NO.1 |
![]() |
![]() |
Disengage the 2 claws and 5 clips.
![]() |
After removing the instrument panel finish panel end, insert your finger into the opening as shown, push the upper portion of the instrument cluster finish panel center and the 2 B claws of the instrument cluster finish panel, and then disengage the claws B.
Disengage the 3 A claws and remove the instrument cluster finish panel.
| 54. REMOVE COMBINATION METER ASSEMBLY |
![]() |
Disconnect the 2 connectors.
Remove the 2 screws and pull the combination meter rearward to remove it.
| 55. REMOVE NO. 1 SWITCH HOLE BASE (for LHD) |
![]() |
Disengage the 2 clips and 2 claws and remove the switch hole base.
| 56. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.
![]() |
Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door assembly.
| 57. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Slide the slider and disconnect the passenger airbag connector.
Disconnect the clamp.
Remove the 2 <C> bolts and 4 <B> screws.

Disconnect the connectors.
Disengage the claw and 3 clips while lifting the rear instrument panel up.
While lifting the instrument panel, slide it toward the rear of the vehicle. Disengage the 5 claws of the front side of the instrument panel and remove the instrument panel.

| 58. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY |
for LHD:
Disconnect the 2 connectors.
Remove the bolt.
Disengage the 4 clamps and remove the No. 2 antenna cord.

for RHD:
Disengage the 2 connectors.
Remove the bolt.
Disengage the 5 clamps and remove the No. 2 antenna cord.

| 59. REMOVE INSTRUMENT PANEL BOX (for LHD) |
![]() |
Open the instrument panel box.
Pull the hinge side of the instrument panel box out horizontally with the instrument panel open and disengage the 2 hinges.
Remove the stopper of the instrument panel box from the cutout of the instrument panel lower and remove the instrument panel box.
| 60. REMOVE ROOF HEADLINING ASSEMBLY |
![]() |
for LHD:
Using a screwdriver, remove the wiring harness clamp.
Disconnect the connector.
![]() |
for RHD:
Using a screwdriver, remove the wiring harness clamp.
![]() |
Remove the No. 1 roof wire from the claw of the junction block.
Disconnect the connector.
![]() |
Remove the antenna cord from the antenna cord clamp.
Disconnect the 2 connectors.
Using a clip remover, remove the 2 connectors.
w/ Curtain Shield Airbag:
for 3 Point Type Rear Center Seat Belt:
for 2 Point Type Rear Center Seat Belt:

w/o Curtain Shield Airbag:
for 3 Point Type Rear Center Seat Belt:
for 2 Point Type Rear Center Seat Belt:

![]() |
Remove the roof headlining from the back door.
| 61. REMOVE ANTENNA CORD SUB-ASSEMBLY |
w/ Curtain Shield Airbag:
Remove the 6 pieces of tape.
Remove the antenna cord from the cutout of the roof headlining.
Remove the antenna cord from the 3 claws of the side rail spacer.

w/o Curtain Shield Airbag:
Remove the 4 pieces of tape.
Remove the antenna cord from the cutout of the roof headlining.
Remove the antenna cord from the 5 claws of the side rail spacer.
