Home › BODY › INTERIOR › ROOF HEADLINING (for Hatchback 3 Door)

ROOF HEADLINING (for Hatchback 3 Door) > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

NOTICE:
Always use "Torx" socket wrench E10 when removing the rear seat.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.



2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)


    B114569E01
  1. Remove the 2 package tray trim suspenders.

  1. Remove the 5 pieces of hook tape.

  1. Disengage the 2 claws and remove the package tray trim.



3. REMOVE DECK BOARD SUB-ASSEMBLY (w/ Deck Board)


    B106371
  1. Release the 2 knobs and remove the deck board.



4. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)


    B119913
  1. Remove the spare wheel cover.



5. REMOVE DECK FLOOR BOX RH (w/ Deck Board)


    B106372
  1. Release the 2 knobs and remove the deck floor box.



6. REMOVE DECK FLOOR BOX LH (w/ Deck Board)

HINT:
Use the same procedure as for the RH side.



7. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)


    B119912
  1. Remove the rear floor carpet.



8. REMOVE NO. 1 REAR SEAT LEG COVER
  1. for RH Side:

    1. Remove the No. 1 rear seat leg cover .

  1. for LH Side:

    1. Remove the No. 1 rear seat leg cover .



9. REMOVE NO. 2 REAR SEAT LEG COVER


    B126921E01
  1. Disengage the 3 claws in the sequence shown in the illustration and remove the No. 1 rear seat leg cover.



10. REMOVE REAR SEAT ASSEMBLY RH


    B114660
  1. Using "TORX" socket wrench E10, remove the 2 bolts and pull up the rear seat cushion.



    B119885
  1. Using "TORX" socket wrench E10, remove the 4 bolts and the rear seat.



11. REMOVE REAR SEAT ASSEMBLY LH


    B114740
  1. Using "TORX" socket wrench E10, remove the 3 bolts and pull up the rear seat cushion.



    B117760
  1. Using "TORX" socket wrench E10, remove the 4 bolts and the rear seat.



12. REMOVE FRONT DOOR SCUFF PLATE RH


    B114494
  1. Disengage the 8 claws and remove the front door scuff plate.



13. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



14. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY RH


    B114571
  1. Disengage the 4 claws and remove the instrument panel under cover.



15. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH


    B114572
  1. Remove the 2 screws.

  1. Disengage the 3 claws and remove the instrument panel under cover.



16. REMOVE COWL SIDE TRIM BOARD RH


    B114285
  1. Disengage the claw and the stud bolt and remove the cowl side trim board.



17. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



18. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B138507
  1. Remove the front door opening trim weatherstrip.



19. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



20. REMOVE FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY RH (w/ Seat Belt Bar)


    B114759
  1. Remove the 2 bolts and the front seat outer belt bar.



21. REMOVE FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY LH (w/ Seat Belt Bar)

HINT:
Use the same procedure as for the RH side.



22. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH


    B114498
  1. Remove the belt of the rear seat outer belt from the rear seat shoulder belt hanger.



    B114499
  1. Disengage the 8 clips, the retainer and the 10 claws and remove the front quarter trim panel.



23. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



24. REMOVE REAR DECK TRIM COVER


    B117692
  1. for Temper Spare Tire:

    1. Using a clip remover, remove the 2 clips.

    2. Disengage the 8 claws and remove the rear deck trim cover.



    B114283
  1. for Grand Tire:

    1. Using a clip remover, remove the 2 clips.

    2. Disengage the 8 claws and remove the rear deck trim cover.



25. REMOVE REAR SEAT OUTER BELT ASSEMBLY RH


    B114500
  1. Remove the bolt.

  1. Disengage the clip and remove the anchor plate.



26. REMOVE REAR SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



27. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    B114501
  1. Remove the 3 screws.

  1. Disengage the 3 clips and the 3 claws and remove the deck side trim panel.



28. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    B114502
  1. w/ Luggage Compartment Room Light:

    1. Remove the 3 screws.

    2. Disengage the 3 clips and the 3 claws.

    3. Disconnect the deck side room light connector and remove the deck side trim panel.

  1. w/o Luggage Compartment Room Light:

    1. Remove the 3 screws.

    2. Disengage the 3 clips and the 3 claws and remove the deck side trim panel.



29. REMOVE SEAT BELT ANCHOR COVER CAP


B114478

HINT:
Use the same procedure for both sides.

  1. Disengage the 3 claws and remove the seat belt anchor cover cap.



30. REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH


    B114479
  1. Remove the bolt and the through anchor.



31. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



32. REMOVE CENTER PILLAR UPPER GARNISH RH


    B114503
  1. Disengage the 2 clips and remove the center pillar garnish.



33. REMOVE CENTER PILLAR UPPER GARNISH LH

HINT:
Use the same procedure as for the RH side.



34. REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY (for 3 Point Type Rear Center Seat Belt)


    B114459
  1. Remove the 2 tongue plates.



    B114460E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and open the slip joint cover.



    B114461
  1. Remove the bolt and the through anchor.



    B114462E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the center belt guide.



35. REMOVE ROOF SIDE INNER GARNISH RH


    B114504E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    Replace the special clip with a new one when the roof side inner garnish is removed.


    1. for 3 Point Type Rear Center Seat Belt:

      1. Disengage the 4 clips and the claw.
      2. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.

    2. for 2 Point Type Rear Center Seat Belt:

      1. Disengage the 4 clips and the claw.
      2. Pass the rear seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.



    B114505
  1. w/o Curtain Shield Airbag:

    1. for 3 Point Type Rear Center Seat Belt:

      1. Disengage the 4 clips and the claw.
      2. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.

    2. for 2 Point Type Rear Center Seat Belt:

      1. Disengage the 4 clips and the claw.
      2. Pass the rear seat outer belt through the slit of the roof side inner garnish and remove the roof side inner garnish.



36. REMOVE ROOF SIDE INNER GARNISH LH


    B114506E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    Replace the special clip with a new one when the roof side inner garnish is removed.


    1. Disengage the 4 clips and claw.

    2. Pass the rear seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.



    B114507
  1. w/o Curtain Shield Airbag:

    1. Disengage the 4 clips and claw.

    2. Pass the rear seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.



37. REMOVE REAR ROOF SIDE RAIL GARNISH RH


    B114508
  1. Disengage the 4 clips and remove the rear roof side rail garnish.



38. REMOVE REAR ROOF SIDE RAIL GARNISH LH

HINT:
Use the same procedure as for the RH side.



39. REMOVE SEAT BELT ANCHOR COVER (for 3 Point Type Rear Center Seat Belt)


    B114464
  1. Using a moulding remover, disengage the 4 claws and remove the seat belt anchor cover.



40. REMOVE ROOF HEADLINING SERVICE HOLE COVER (w/o Curtain Shield Airbag)


B114299E01

HINT:
The number of the roof headlining service hole covers varies with the specifications.

  1. Using a clip remover with its tip wrapped in protective tape, remove the 6 roof headlining service hole covers.



41. REMOVE COAT HOOK (w/ Coat Hook)


    B124367E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and open the cover.



    B124368E01
  1. Using a clip remover with its tip wrapped in protective tape, disengage the 2 claws and remove the coat hook.



42. REMOVE ASSIST GRIP COVER


B114301E01

HINT:
The number of the assist grip covers varies with the specifications.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 assist grip covers.



43. REMOVE ASSIST GRIP SUB-ASSEMBLY


B114302

HINT:
The number of the assist grips varies with the specifications.

  1. Disengage the 2 springs and remove the assist grip.



44. REMOVE VISOR ASSEMBLY RH


    B114303E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the visor bracket cover.



    B114304
  1. Remove the visor shaft from the visor holder.

  1. Disengage the 2 springs and remove the visor.



45. REMOVE VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



46. REMOVE VISOR HOLDER RH


    B114305E01
  1. Disengage the 2 claws by turning the visor counterclockwise between 60 to 120° and remove the visor holder.

    HINT:
    The claw may be damaged during removal. However, it is reusable because this does not effect its function.



47. REMOVE VISOR HOLDER LH

HINT:
Use the same procedure as for the RH side.



48. REMOVE ROOM LIGHT ASSEMBLY


    B114306E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light lens.



    B124365E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 covers.



    B114307E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws.



    B114308E01
  1. Remove the roof wire from the claw of the room light.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base and the room light.



49. REMOVE MAP LIGHT ASSEMBLY


    B114309E01
  1. Using a roof moulding remover, disengage the 4 claws.



    B114310
  1. Disconnect the map light connector and remove the map light.



50. REMOVE FRONT PILLAR GARNISH RH


    B117693E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B117694
  1. w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B114312
  1. Disconnect the connector.

  1. Using a clip remover, remove the 3 antenna cord clamps.



    B127674
  1. w/ Front No. 2 Speaker:

    1. Disconnect the speaker connector.



    2. B127670E01
    3. Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.



  1. w/ Curtain Shield Airbag:



      B114313E01
    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
      Protective cover size: 
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)



51. REMOVE FRONT PILLAR GARNISH LH


    B117695E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B117696
  1. w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B114316
  1. Using a clip remover, remove the 4 wire harness clamps.



    B127673
  1. w/ Front No. 2 Speaker:

    1. Disconnect the speaker connector.



    2. B127669E01
    3. Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.



    B114317E01
  1. w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
      Protective cover size: 
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)



52. REMOVE INSTRUMENT PANEL FINISH PANEL END RH


E107743E01
  1. with CD player

    1. Pull the instrument panel finish panel end RH and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.



    E107744E01
  1. Except CD player

    1. Pull the instrument panel finish panel end RH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.



53. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


E107741E01
  1. with CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.



    E107742E01
  1. Except CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.



54. REMOVE INSTRUMENT CLUSTER FINISH PANEL NO.1


B132363E01

NOTICE:
Follow the procedure below to remove the instrument cluster finish panel. Claw A will break if the instrument cluster finish panel is raised carelessly.



    B132364
  1. Disengage the 2 claws and 5 clips.



    B132365E01
  1. After removing the instrument panel finish panel end, insert your finger into the opening as shown, push the upper portion of the instrument cluster finish panel center and the 2 B claws of the instrument cluster finish panel, and then disengage the claws B.

  1. Disengage the 3 A claws and remove the instrument cluster finish panel.



55. REMOVE COMBINATION METER ASSEMBLY


E107730
  1. Disconnect the 2 connectors.

  1. Remove the 2 screws and pull the combination meter rearward to remove it.



56. REMOVE NO. 1 SWITCH HOLE BASE (for LHD)


B108201
  1. Disengage the 2 clips and 2 claws and remove the switch hole base.



57. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


B108202
  1. Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.



    B105351
  1. Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door assembly.

    NOTICE:
    Pull the glove compartment door out horizontally, otherwise, installation failure caused by excessive play around the hinge portion will result.



58. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY


B108181E02
  1. Slide the slider and disconnect the passenger airbag connector.

  1. Disconnect the clamp.



  1. Remove the 2 <C> bolts and 4 <B> screws.


    B105354E01

  1. Disconnect the connectors.

  1. Disengage the claw and 3 clips while lifting the rear instrument panel up.



  1. While lifting the instrument panel, slide it toward the rear of the vehicle. Disengage the 5 claws of the front side of the instrument panel and remove the instrument panel.


    B105355E01



59. REMOVE INSTRUMENT PANEL BOX (for LHD)


B108188E01
  1. Open the instrument panel box.

  1. Pull the hinge side of the instrument panel box out horizontally with the instrument panel open and disengage the 2 hinges.

  1. Remove the stopper of the instrument panel box from the cutout of the instrument panel lower and remove the instrument panel box.



60. REMOVE ROOF HEADLINING ASSEMBLY


    B114511
  1. for LHD:

    1. Using a screwdriver, remove the wiring harness clamp.

    2. Disconnect the connector.



    B114319
  1. for RHD:

    1. Using a screwdriver, remove the wiring harness clamp.



    2. B114320
    3. Remove the No. 1 roof wire from the claw of the junction block.

    4. Disconnect the connector.



    B114321
  1. Remove the antenna cord from the antenna cord clamp.

  1. Disconnect the 2 connectors.

  1. Using a clip remover, remove the 2 connectors.



  1. w/ Curtain Shield Airbag:

    1. for 3 Point Type Rear Center Seat Belt:

      1. Using a clip remover, remove the clip.
      2. Disengage the 4 hooks.



    2. for 2 Point Type Rear Center Seat Belt:

      1. Using a clip remover, remove the 2 clips.
      2. Disengage the 4 hooks.


      B119919E01



  1. w/o Curtain Shield Airbag:

    1. for 3 Point Type Rear Center Seat Belt:

      1. Using a clip remover, remove the clip.
      2. Disengage the 2 claws and the 4 hooks.



    2. for 2 Point Type Rear Center Seat Belt:

      1. Using a clip remover, remove the 2 clips.
      2. Disengage the 2 claws and the 4 hooks.


      B119920E01



    B114515
  1. Remove the roof headlining from the back door.



61. REMOVE NO. 5 ROOF SILENCER PAD


B127689

HINT:
Only remove the No. 5 roof silencer pad when the No. 1 roof wire and the roof headlining are replaced.

  1. Remove the 2 No. 5 roof silencer pads.



62. REMOVE NO. 1 ROOF SILENCER PAD

HINT:
Only remove the No. 1 roof silencer pad when the No. 1 roof wire and the roof headlining are replaced.



  1. Remove the 4 No. 1 roof silencer pads.


    B127679



63. REMOVE REAR ROOF SILENCER PAD


B127680

HINT:
Only remove the rear roof silencer pad when the roof headlining is replaced.

  1. Remove the 2 rear roof silencer pads.



64. REMOVE NO. 1 ROOF WIRE


B127681E01

HINT:
Only remove the No. 1 roof wire when the roof headlining is replaced.

  1. w/ Curtain Shield Airbag:

    1. Remove the 7 pieces of tape.

    2. Remove the No. 1 roof wire from the claw of the side rail spacer.



    B127682E01
  1. w/o Curtain Shield Airbag:

    1. Remove the 6 pieces of tape.

    2. Remove the No. 1 roof wire from the 2 claws of the side rail spacer.



65. REMOVE ANTENNA CORD SUB-ASSEMBLY

HINT:
Only remove the antenna cord when the roof headlining is replaced.



  1. w/ Curtain Shield Airbag:

    1. Remove the 6 pieces of tape.

    2. Remove the antenna cord from the cutout of the roof headlining.



    3. Remove the antenna cord from the 3 claws of the front and rear side rail spacers.


      B127683E01



  1. w/o Curtain Shield Airbag:

    1. Remove the 4 pieces of tape.

    2. Remove the antenna cord from the cutout of the roof headlining.



    3. Remove the antenna cord from the 5 claws of the front and rear side rail spacers.


      B127684E01



66. REMOVE FRONT SIDE RAIL SPACER RH


B127685E01

HINT:
Only remove the front side rail spacer when the roof headlining is replaced.

  1. w/ Curtain Shield Airbag:

    1. Remove the 3 adhesion portions and the front side rail spacer.



    B127686E01
  1. w/o Curtain Shield Airbag:

    1. Remove the 4 adhesion portions and the front side rail spacer.



67. REMOVE FRONT SIDE RAIL SPACER LH

HINT:
Use the same procedure as for the RH side.



68. REMOVE REAR SIDE RAIL SPACER RH

HINT:
Only remove the rear side rail spacer when the roof headlining is replaced.



    B127687E01
  1. w/ Curtain Shield Airbag:

    1. Remove the 2 adhesion portions and the rear side rail spacer.



    B127688E01
  1. w/o Curtain Shield Airbag:

    1. Remove the 4 adhesion portions and the rear side rail spacer.



69. REMOVE REAR SIDE RAIL SPACER LH

HINT:
Use the same procedure as for the RH side.