Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › CURTAIN SHIELD AIRBAG ASSEMBLY (for Sedan)

CURTAIN SHIELD AIRBAG ASSEMBLY (for Sedan) > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

HINT:
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE FRONT SEAT HEADREST ASSEMBLY


B138501E01

HINT:
Use the same procedure for both sides.

  1. Push in the lock button of the front seat headrest support and remove the front seat headrest.



3. REMOVE FRONT SEAT ASSEMBLY LH


    B138315E01
  1. w/ Front Seat Side Airbag:

    1. Slide the slider and disconnect the airbag connector.

  1. Disconnect the buckle switch connector.



    B138317
  1. Move the front seat to its most rearward position.

  1. Using "TORX" socket wrench E10, remove the 2 bolts from the front side.

  1. Move the front seat to its most forward position.

  1. Using "TORX" socket wrench E10, remove the 2 bolts from the rear side and the front seat.



4. REMOVE FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



5. REMOVE REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY
  1. for 60/40 Split Seat Type:

    1. Remove the rear seat cushion cover pad sub-assembly .

  1. for Fixed Seat Type:

    1. Remove the rear seat cushion cover pad sub-assembly .



6. REMOVE REAR SEATBACK ASSEMBLY (for Fixed Seat Type)


    B138450E02
  1. Remove the rear seat outer belt from the rear seat shoulder belt guide.

    HINT:
    Use the same procedure for both sides.

  1. for 3 Point Type Rear Center Seat belt:

    1. Remove the rear center seat outer belt from the rear center seat shoulder belt guide.



    B134981
  1. Remove the 3 bolts.

  1. Disengage the 3 hooks and remove the rear seatback.



7. REMOVE REAR SEATBACK ASSEMBLY LH (for 60/40 Split Seat Type)


    B134924
  1. Remove the rear seat outer belt from the rear seat shoulder belt guide.

  1. Pull the rear seatback lock release button and tilt the rear seatback forward.



    B134925
  1. Using a clip remover, remove the 2 clips and the rear seatback cover.



    B134926
  1. Remove the 2 bolts, the 2 hooks and the rear seatback.



8. REMOVE REAR SEATBACK ASSEMBLY RH (for 60/40 Split Seat Type)


    B134943
  1. Remove the rear seat outer belt from the rear seat shoulder belt guide.

  1. for 3 Point Type Rear Center Seat Belt:

    1. Remove the rear center seat outer belt from the rear center seat shoulder belt guide.

  1. Pull the rear seatback lock release button and tilt the rear seatback forward.



    B134944
  1. Using a clip remover, remove the 2 clips and the rear seatback cover.



    B134945
  1. Remove the 2 bolts, the 2 hooks and the rear seatback.



9. REMOVE LUGGAGE COMPARTMENT FLOOR MAT (for Fixed Seat Type)


B136269
  1. Remove the luggage compartment floor mat.



10. REMOVE SPARE WHEEL COVER ASSEMBLY (for 60/40 Split Seat Type)


B136270
  1. Remove the spare wheel cover.



11. REMOVE LUGGAGE COMPARTMENT TRIM INNER PAD (for 60/40 Split Seat Type)


B136275
  1. Remove the luggage compartment trim inner pad.



12. REMOVE FRONT DOOR SCUFF PLATE RH


    B134764
  1. Disengage the 11 claws and remove the front door scuff plate.



13. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



14. REMOVE COWL SIDE TRIM BOARD RH


    B114285
  1. Disengage the claw and the stud bolt and remove the cowl side trim board.



15. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



16. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B134765
  1. Remove the front door opening trim weatherstrip.



17. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



18. REMOVE REAR DOOR SCUFF PLATE RH


    B134771
  1. Disengage the 7 claws and remove the rear door scuff plate.



19. REMOVE REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



20. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B134772
  1. Remove the rear door opening trim weatherstrip.



21. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



22. REMOVE REAR SEAT SIDE COVER RH


    B134776
  1. Disengage the 2 clips and the 4 claws and remove the rear seat side cover.



23. REMOVE REAR SEAT SIDE COVER LH

HINT:
Use the same procedure as for the RH side.



24. REMOVE ROOF SIDE INNER GARNISH RH


    B134775E01
  1. Disengage the 4 clips and the claw and remove the roof side inner garnish.

    NOTICE:
    Replace the special clip with a new one when the roof side inner garnish is removed.



25. REMOVE ROOF SIDE INNER GARNISH LH

HINT:
Use the same procedure as for the RH side.



26. REMOVE CENTER PILLAR LOWER GARNISH RH


    B134767
  1. Disengage the 3 claws and 2 clips and remove the center pillar lower garnish.



27. REMOVE CENTER PILLAR LOWER GARNISH LH

HINT:
Use the same procedure as for the RH side.



28. REMOVE SEAT BELT ANCHOR COVER CAP


B138431E01

HINT:
Use the same procedure for both sides.

  1. Pull portion A, shown in the illustration, toward you, remove the 2 claws on the lower side followed by the claw on the upper side. Then remove the seat belt anchor cover cap.



29. REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH


    B114296
  1. Remove the bolt and the through anchor.



30. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



31. REMOVE CENTER PILLAR UPPER GARNISH RH


    B134768
  1. Disengage the 2 clips and 2 hooks and remove the center pillar upper garnish.



32. REMOVE CENTER PILLAR UPPER GARNISH LH

HINT:
Use the same procedure as for the RH side.



33. REMOVE FRONT PILLAR GARNISH RH


    B134777E01
  1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.



    B134787
  1. Disconnect the antenna connector.

  1. Using a clip remover, remove the 3 clamps.



    B138437E01
  1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

    Protective cover size:
    Area
    Measurement
    a
    700 mm (27.56 in.)
    b
    120 mm (4.72 in.)



34. REMOVE FRONT PILLAR GARNISH LH


    B134778E01
  1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.



    B134789
  1. Using a clip remover, remove the 4 clamps.



    B138438E01
  1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

    Protective cover size:
    Area
    Measurement
    a
    700 mm (27.56 in.)
    b
    120 mm (4.72 in.)



35. REMOVE INSTRUMENT LOWER CENTER PANEL FINISH PANEL


B132316
  1. Disengage the 2 claws and 2 clips and remove the instrument panel finish panel lower center.



36. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    B132387
  1. Remove the shift lever knob.



37. REMOVE REAR CONSOLE BOX UPPER FRONT PANEL SUB-ASSEMBLY


    B132347
  1. Shift the shift lever into the N position.

  1. Disengage the 5 clips and the claw and remove the upper console panel.



38. REMOVE REAR CONSOLE BOX UPPER REAR PANEL SUB-ASSEMBLY


    B132348
  1. Disengage the 3 clips and 3 claws.

  1. Disconnect the connector and remove the console upper rear panel.



39. REMOVE CONSOLE BOX CARPET


B132346
  1. Remove the console box carpet.



40. REMOVE REAR CONSOLE BOX ASSEMBLY


    B132349
  1. Disconnect the clamp.

  1. Remove the 2 bolts and 2 screws.

  1. Disengage the 4 claws and remove the rear console box.



41. REMOVE INSTRUMENT PANEL FINISH PANEL END RH


B132318
  1. Disengage the 6 claws and 3 clips and remove the instrument panel finish panel end RH.



42. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


B132317
  1. Disengage the 6 claws and 3 clips and remove the instrument panel finish panel end LH.



43. REMOVE INSTRUMENT CLUSTER FINISH PANEL NO.1


E116832
  1. Disengage the 4 claws and 5 clips and remove the instrument cluster finish panel.



44. REMOVE COMBINATION METER ASSEMBLY


E116819
  1. Disconnect the 2 connectors.

  1. Remove the 2 screws and pull the combination meter rearward to remove it.



45. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


B132319E01
  1. Disengage the claw and separate the glove compartment door stopper from the glove compartment door.

  1. Slightly flex the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door until it becomes horizontal.



    B132320E01
  1. Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door.

    NOTICE:
    Pull the glove compartment door out horizontally, otherwise, installation failure caused by excessive play around the hinge portion will result.



46. REMOVE INSTRUMENT UPPER PANEL SUB-ASSEMBLY


B132322E01
  1. Slide the slider and disconnect the passenger airbag connector.

  1. Disconnect the clamp.



  1. Remove the 2 <C> bolts and 2 <B> screws.


    B132323E01



  1. Disengage the 7 clips by lifting the rear side of the instrument panel up.


    B132324

  1. While lifting the instrument panel, slide it toward the rear of the vehicle. Disengage the 5 claws from the front side of the instrument panel and remove the instrument panel.



47. REMOVE INSTRUMENT PANEL BOX (for LHD)


B132334E01
  1. Open the instrument panel box.

  1. Pull the instrument panel box out horizontally with the instrument panel open and disengage the 2 hinges.



    B132335E01
  1. Remove the stopper of the instrument panel box from the cutout of the instrument panel lower and remove the instrument panel box.



48. REMOVE ASSIST GRIP COVER


B134785

HINT:
The number of the assist grip covers varies with the specifications.



    B114301E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip cover.



49. REMOVE ASSIST GRIP SUB-ASSEMBLY


B134786

HINT:
The number of the assist grips varies with the specifications.



    B114302
  1. Disengage the 2 springs and remove the assist grip.



50. REMOVE VISOR ASSEMBLY RH


    B114303E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the visor bracket cover.



    B114304
  1. Remove the visor shaft from the visor holder.

  1. Disengage the 2 springs and remove the visor.



51. REMOVE VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



52. REMOVE VISOR HOLDER RH


    B114305E01
  1. Disengage the 2 claws by turning the visor counterclockwise between 60 to 120° and remove the visor holder.

    HINT:
    The claw may be damaged during removal. However, it is reusable because this does not effect its function.



53. REMOVE VISOR HOLDER LH

HINT:
Use the same procedure as for the RH side.



54. REMOVE ROOM LIGHT ASSEMBLY


    B114306E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light lens.



    B138435E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.

    HINT:
    Use the same procedure for both sides.



    B114307E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light.



    B138436E01
  1. Remove the roof wire from the claw of the room light.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and disconnect the room light switch base.



55. REMOVE MAP LIGHT ASSEMBLY


    B114309E01
  1. Using a moulding remover, disengage the 4 claws and remove the map light.



    B138432
  1. Disconnect the map light connector.



56. REMOVE ROOF HEADLINING ASSEMBLY


    B134790
  1. Using a clip remover, remove the 2 clamps.



    B134791
  1. for LHD:

    1. Disconnect the roof wire connector.



    B134792
  1. for RHD:

    1. Disconnect the roof wire connector.

    2. Remove the roof wire from the clamp.



    B134788
  1. Using a clip remover, remove the clamp.

  1. Disconnect the antenna connector.



    B134793
  1. w/ Curtain Shield Airbag:

    1. Using a clip remover, remove the 2 clips.

    2. Disengage the 4 hooks.



    B134794
  1. w/o Curtain Shield Airbag:

    1. Using a clip remover, remove the 2 clips.

    2. Disengage the 2 claws and 4 hooks.



    B134795
  1. Remove the roof headlining from the front door.



57. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY


    C128117E01
  1. Using a thin-bladed screwdriver, release the locking button.

  1. Using a thin-bladed screwdriver, detach the airbag connector.



  1. Remove the 9 bolts, disengage the 3 hooks and remove the curtain shield airbag.


    B135707E01



58. REMOVE CURTAIN SHIELD AIR BAG BRACKET RH


    C128119
  1. Remove the bolt, disengage the 2 hooks and remove the curtain shield airbag bracket.



59. REMOVE ROOF SIDE RAIL BRACKET RH


    C129259
  1. Remove the 2 bolts, disengage the 2 hooks and remove the roof side rail bracket.