Home › TRANSMISSION ยท U441E AUTOMATIC TRANSAXLE › SPEED SENSOR (for Hatchback)

SPEED SENSOR (for Hatchback) > INSTALLATION

for Preparation Click here



1. INSTALL SPEEDOMETER DRIVEN GEAR


    C117097E02
  1. Coat a new O-ring with Toyota Genuine ATF Type T-IV or equivalent and install it onto the speedometer sensor.

  1. Install the driven gear into the speedometer sensor with the clip.



2. INSTALL SPEEDOMETER SENSOR


    C186726
  1. Install the speedometer sensor with the bolt.

    Torque:
    11 N*m{ 115 kgf*cm , 8 ft.*lbf }

  1. Connect the speedometer sensor connector.



3. INSTALL BATTERY CARRIER


A117309
  1. Install the battery carrier with the 5 bolts.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Install the clamp.



4. INSTALL BATTERY TRAY


5. INSTALL BATTERY
  1. Install the battery onto the vehicle with the battery clamp.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

  1. Connect the cable to the battery terminal.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



6. INSTALL OUTER COWL TOP PANEL


A115392
  1. Install the cowl top panel with the 9 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }



    A108438
  1. Connect the wire harness clamp.



7. INSTALL NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY


A108437
  1. Engage the claw to install cowl to register duct No. 2.



8. INSTALL FRONT WIPER MOTOR AND LINK


E113861
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



9. INSTALL COWL TOP VENTILATOR LOUVER LH


E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.



10. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


E113854
  1. Connect the washer hose.



    E113852
  1. Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.



    E117641
  1. Engage the 2 hooks and install cowl top ventilator louver center No. 1.



11. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113862E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



12. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113863E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



13. INSTALL FRONT WIPER ARM HEAD CAP


E113849
  1. Engage the claw and install the 2 front wiper arm head caps.