Home › TRANSMISSION ยท U441E AUTOMATIC TRANSAXLE › TRANSMISSION WIRE

TRANSMISSION WIRE > INSTALLATION

for Preparation Click here



1. INSTALL TRANSMISSION WIRE
  1. Coat a new O-ring with Toyota Genuine ATF Type T-IV and install it into the transmission wire.



    D025196
  1. Pass the transmission wire through the transaxle.



    C057520
  1. Install the transmission wire with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



2. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


C059784
  1. Coat new governor apply gasket No. 1 with Toyota Genuine ATF Type T-IV and install it onto the transaxle case.



    C057516E02
  1. Connect the connecting rod to the manual valve lever, and install the valve body.



    D025197E01
  1. Provisionally install the valve body with the 14 bolts.

    Bolt length:
    Bolt A:
    20 mm (0.79 in.)
    Bolt B:
    28 mm (1.10 in.)
    Bolt C:
    49 mm (1.93 in.)
    Bolt D:
    36 mm (1.42 in.)
    Bolt E:
    40 mm (1.57 in.)

  1. Tighten the 14 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }



    D025198E01
  1. Connect the 5 shift solenoid valve connectors and ATF temperature sensor.



3. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


C057509
  1. Install a new oil strainer gasket onto the oil strainer.



    C057507
  1. Install the oil strainer with the 3 bolts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }



4. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


C057519E01
  1. Install the 2 magnets onto the oil pan, as shown in the illustration.



    C057506
  1. Install the oil pan and a new gasket with the 18 bolts.

    Torque:
    7.0 N*m{ 70 kgf*cm , 61 in.*lbf }



5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



6. ADD AUTOMATIC TRANSAXLE FLUID

Automatic transaxle fluid type:
Toyota Genuine ATF Type T-IV

Automatic Transaxle Fluid Capacity (Reference) 
Drain and refill
2.5 liters (2.6 US qts, 2.2 Imp. qts)
Dry fill
5.6 liters (5.9 US qts, 4.9 Imp. qts)


7. INSPECT AUTOMATIC TRANSAXLE FLUID


D025120E03

HINT:
Drive the vehicle until the engine and transaxle are at normal operating temperature.

Fluid temperature:
70 to 80 °C (158 to 176 °F)

  1. Park the vehicle on a level surface and engage the parking brake.

  1. With the engine idling and the brake pedal depressed, shift the shift lever into all positions from P to L, and then return it to the P position.

  1. Pull out the oil level gauge and wipe it clean.

  1. Push it fully back into the pipe.

  1. Pull it out and check that the fluid level is within the HOT range.
    If there is any leakage, repair or replace O-rings, FIPGs, oil seals, plugs or other parts.



8. CHECK FOR AUTOMATIC TRANSAXLE FLUID LEAKAGE


9. INSTALL ENGINE UNDER COVER LH