Home › TRANSMISSION ยท U441E AUTOMATIC TRANSAXLE › TRANSMISSION CONTROL CABLE ASSEMBLY (for Hatchback)

TRANSMISSION CONTROL CABLE ASSEMBLY (for Hatchback) > INSTALLATION

for Preparation Click here



1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY


C107765
  1. Install the control cable onto the control shaft lever with the nut.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Fix the control cable onto the control cable bracket with a new clip.

  1. Connect the control cable to the clamp.



    C117117
  1. Install the control cable with the 3 nuts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    C118484E01
  1. Turn the nut of the control cable and push in the lock.



    C121646
  1. Install the control cable onto the shift lever retainer.

    NOTICE:
    1. Install the cable with the protruding portion of the cable outer facing upward.
    2. After installing, check that the lock of the cable outer is protruding beyond portion A-A, as shown in the illustration.



    C117115
  1. Connect the control cable to the shift lever.

    NOTICE:
    Connect the control cable so that the adjusting mechanism lock of the control cable is installed on the left side of the vehicle.



2. INSTALL FRONT FLOOR HEAT INSULATOR NO.1


C117116E01
  1. Install floor insulator No. 1 with the 2 bolts and the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



3. INSTALL EXHAUST PIPE ASSEMBLY FRONT


A104634
  1. Using vernier calipers, measure the free length of the compression spring.

    Minimum length (Front side:
    40.5 mm (1.594 in.)

    Minimum length (Rear side):
    38.5 (1.516 in.)

    If the length is not as specified, replace the compression spring.



    A104635E01
  1. Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

    NOTICE:
    1. Install the exhaust pipe gasket in the correct direction.
    2. Do not damage the outer surface of the exhaust pipe gasket.
    3. Do not reuse the exhaust pipe gasket.
    4. Do not push in the gasket with the exhaust pipe when connecting it.

  1. Install the 3 No. 4 exhaust pipe supports.



  1. Install the exhaust front pipe assembly and a new exhaust pipe gasket with the 4 compression springs and 4 bolts.

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }



    A119126



4. CONNECT OXYGEN SENSOR CONNECTOR


C117113
  1. Insert the oxygen sensor connector toward the room side, through the hole in the floor panel, and then install the grommet.

  1. Connect the oxygen sensor connector.



5. INSTALL AIR CLEANER BRACKET


A117308
  1. Install the air cleaner bracket with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Connect the wire harness clamp to the air cleaner bracket.



6. INSTALL AIR CLEANER ASSEMBLY


A104895
  1. Install the air cleaner case with air cleaner inlet No. 1 with the 2 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

  1. Connect the wire harness to the air cleaner case.

  1. Install the air cleaner element.



    A117355
  1. Install and lock the air cleaner cap and air cleaner hose and then tighten the air cleaner hose clamp.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the ventilation hose to the air cleaner hose.

  1. Connect the vacuum switching valve connector and wire harness clamp.

  1. Connect the fuel vapor feed hose and fuel vapor feed hose No. 1 to the vacuum switching valve assembly.

  1. Connect the intake air flow meter connector and wire harness clamp.



7. INSTALL BATTERY TRAY


8. INSTALL BATTERY
  1. Install the battery onto the vehicle with the battery clamp.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

  1. Connect the cable to the battery terminal.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



9. INSPECT SHIFT LEVER POSITION
  1. When shifting the lever from P to the R position with the ignition switch ON and the brake pedal depressed, make sure that the shift lever moves smoothly and moves correctly into position.

  1. Start the engine and make sure that the vehicle moves forward when shifting the lever from N to the D position and moves rearward when shifting the lever to the R position.
    If the operation cannot be performed as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.



10. ADJUST SHIFT LEVER POSITION
  1. Shift the shift lever to the N position.



    C117121E01
  1. Slide the adjuster case cover in the direction shown in the illustration and pull out the lock piece.

  1. Gently pull the cable rod toward the rear of the vehicle by hand to pull the cable taut.



    C117120E01
  1. Press the lock piece into the adjuster case and lock it.



    C117119E01
  1. Slide the cover in the direction shown in the illustration.

    NOTICE:
    Slide the cover past the protrusion of the lock piece.

  1. Inspect the operation after the adjustment.



11. INSTALL CONSOLE BOX ASSEMBLY REAR


C116873
  1. Engage the 2 clips and install the console box with the bolt.



12. INSTALL CONSOLE BOX CARPET


C109008
  1. Install the console box carpet.



13. INSTALL CONSOLE BOX COVER REAR


C109006E01
  1. Engage the 8 claws to install the console box rear cover.



14. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
  1. Install the shift lever knob sub-assembly onto the shift lever.



15. CHECK FOR EXHAUST GAS LEAKAGE