Home › TRANSMISSION ยท U340E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY


    C121659
  1. Remove the bolt and remove the speedometer driven hole cover.

  1. Remove the O-ring from the speedometer driven hole cover.



2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C117101
  1. Remove the nut and washer and remove the control lever shaft.



    C117104
  1. Using a screwdriver, pry out the lock plate and remove the manual valve shaft nut.



    C117106
  1. Remove the 2 bolts and pull out the park/neutral position switch assembly.



3. REMOVE TRANSMISSION REVOLUTION SENSOR


    C067751
  1. Remove the bolt and remove the transmission revolution sensor.



4. REMOVE OIL COOLER TUBE UNION


    D025286
  1. Remove the 2 oil cooler tube unions from the transaxle case.

  1. Remove the 2 O-rings from the 2 oil cooler tube unions.



5. REMOVE TRANSAXLE CASE NO. 1 PLUG


    C067754
  1. Remove the 4 transaxle case No. 1 plugs from the transaxle housing and transaxle case.



    C067755
  1. Remove the transaxle case No. 1 plug from the transaxle case.

  1. Remove the O-rings from the transaxle case No. 1 plugs.



6. REMOVE BREATHER PLUG HOSE


    C067752
  1. Remove the breather plug hose from the transaxle case.



7. FIX AUTOMATIC TRANSAXLE ASSEMBLY


8. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


    C062684E03
  1. Remove the 19 bolts and remove the oil pan and oil pan gasket.



    C093943E04
  1. Remove the 2 oil cleaner magnets from the oil pan.

  1. Examine the particles in the pan.

    1. Collect any steel chips with the removed magnets.
      Carefully look at the foreign matter and particles in the pan and on the magnets to predict the type of wear which might be found in the transaxle.
      Steel (magnetic): bearing, gear and clutch plate wear
      Brass (non-magnetic): bearing wear



9. REMOVE VALVE BODY OIL STRAINER ASSEMBLY


    C062685E02
  1. Remove the 3 bolts and remove the oil strainer assembly.



    D005904E04
  1. Remove the oil strainer gasket from the oil strainer.



10. REMOVE TRANSMISSION VALVE BODY ASSEMBLY


    C093938E05
  1. Disconnect the 5 solenoid connectors.

  1. Remove the bolt and lock plate and remove the ATF temperature sensor.



    C093939E07
  1. Remove the 2 bolts and remove the detent spring cover and detent spring.



    C093940E10
  1. Remove the 13 bolts and the valve body assembly from the transaxle case.



11. REMOVE TRANSMISSION WIRE


    C062929
  1. Remove the bolt and the transmission wire from the transaxle case.



    C067760
  1. Remove the O-ring from the transmission wire.



12. REMOVE TRANSAXLE CASE 2ND BRAKE GASKET


    C067757
  1. Remove the transaxle case 2nd brake gasket from the transaxle case.



13. REMOVE TRANSAXLE CASE GASKET


    C067758
  1. Remove the transaxle case gasket from the transaxle case.



14. REMOVE BRAKE DRUM GASKET


    C067759
  1. Remove the brake drum gasket from the transaxle case.



15. REMOVE CHECK BALL BODY


    C067767
  1. Remove the check ball body and spring from the transaxle case.



16. REMOVE B-2 ACCUMULATOR PISTON


    C067761
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-2 accumulator piston and spring.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a shop rag or piece of cloth.
    2. Do not splash ATF with the compressed air.



    D025038
  1. Remove the 2 O-rings from the B-2 accumulator piston.



17. REMOVE C-3 ACCUMULATOR PISTON


    C067762
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-3 accumulator piston and spring.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it with your hand using a shop rag or piece of cloth.
    2. Do not splash ATF with the compressed air.



    D025039
  1. Remove the 2 O-rings from the C-3 accumulator piston.



18. REMOVE C-2 ACCUMULATOR PISTON


    C067763
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-2 accumulator piston and the spring.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a shop rag or piece of cloth.
    2. Do not splash ATF with the compressed air.



    D025040
  1. Remove the 2 O-rings from the C-2 accumulator piston.



19. REMOVE TRANSAXLE HOUSING


    D025041
  1. Remove the 14 bolts.

  1. Tap around the circumference of the transaxle housing with a plastic hammer to remove the transaxle housing from the transaxle case.

    NOTICE:
    The differential gear assembly may be accidentally removed when the transaxle housing is removed.



20. INSPECT INPUT SHAFT END PLAY


    C067772
  1. Measure the end play in the axial direction.

    End play:
    0.37 to 1.29 mm (0.0146 to 0.0508 in.)

    If the end play is not as specified, select and replace the thrust needle roller bearing.



21. REMOVE OIL PUMP ASSEMBLY


    C067773
  1. Remove the 7 bolts and the oil pump assembly from the transaxle case.



22. REMOVE DIFFERENTIAL GEAR ASSEMBLY


    D025042
  1. Remove the differential gear assembly from the transaxle case.



23. REMOVE OVERDRIVE BRAKE GASKET


    C067783
  1. Using a screwdriver, remove the 2 overdrive brake gaskets from the transaxle case.



24. REMOVE INPUT SHAFT ASSEMBLY


    C067775
  1. Remove the input shaft assembly from the transaxle case.



25. REMOVE STATOR SHAFT THRUST NEEDLE ROLLER BEARING


    C067782
  1. Remove the thrust needle roller bearing from the input shaft.



26. REMOVE FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING


    C067776
  1. Remove the thrust needle roller bearing from the forward clutch hub.



27. INSPECT INTERMEDIATE SHAFT ASSEMBLY


    D025043
  1. Using a dial indicator, measure the clearance of the intermediate shaft.

    Standard clearance:
    0.204 to 0.966 mm (0.008 to 0.038 in.)



28. REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY


    C067777
  1. Remove the forward clutch hub from the transaxle case.



29. REMOVE TRANSAXLE REAR COVER ASSEMBLY


    C067778
  1. Remove the 11 bolts.

  1. Tap around the circumference of the transaxle rear cover with a plastic hammer to remove the transaxle rear cover from the transaxle case.



30. REMOVE TRANSAXLE CASE GASKET


    C067779
  1. Remove the 4 transaxle case gaskets.



31. REMOVE REAR CLUTCH DRUM THRUST NEEDLE ROLLER BEARING


    C067780
  1. Using a magnetic finger, remove the thrust needle roller bearing.



32. REMOVE INTERMEDIATE SHAFT ASSEMBLY


    C067781
  1. Remove the intermediate shaft assembly from the transaxle case.



33. REMOVE 2ND COAST AND OVERDRIVE BRAKE DISC


    C067785
  1. Remove the flange, 2 discs and 2 flanges No. 2 from the transaxle.



34. REMOVE THRUST NEEDLE ROLLER BEARING


    C067784
  1. Using a magnetic finger, remove the C-2 hub thrust bearing race, the thrust needle roller bearing and the thrust bearing race from the direct clutch hub.



35. REMOVE DIRECT CLUTCH HUB


    C068196
  1. Remove the direct clutch hub from the transaxle case.



36. REMOVE REAR PLANETARY SUN GEAR NO. 2 THRUST NEEDLE ROLLER BEARING


    C067786
  1. Using a magnetic finger, remove the thrust bearing from the rear thrust needle bearing.



37. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY


    C067973
  1. Remove the rear planetary sun gear from the transaxle case.



38. REMOVE REAR PLANETARY SUN GEAR THRUST NEEDLE ROLLER BEARING


    C068161
  1. Remove the rear planetary sun gear thrust needle roller bearing and thrust washer No. 1 from the rear planetary sun gear.



39. INSPECT 1-WAY CLUTCH ASSEMBLY


    D025044E07
  1. Hold the rear planetary sun gear and turn the 1-way clutch.

  1. Make sure that 1-way clutch turns freely counterclockwise and locks when turned clockwise.



40. REMOVE 1-WAY CLUTCH ASSEMBLY


    C068163
  1. Remove the 1-way clutch assembly and planetary carrier thrust washer No. 2 from the rear planetary sun gear.



41. REMOVE 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING


    C067971
  1. Using a screwdriver, remove the snap ring from the transaxle case.



42. REMOVE 2ND BRAKE BRAKE DISC


    C067969
  1. Using a screwdriver, remove the snap ring.

  1. Remove the flange, 3 discs and 3 plates from the transaxle.



43. REMOVE 2ND BRAKE PISTON SLEEVE


    C067970
  1. Remove the 2nd brake piston sleeve from the transaxle case.



44. INSPECT 1-WAY CLUTCH NO. 2


    D025045E06
  1. Install the 1-way clutch and the thrust washer onto the rear planetary sun gear.

  1. Hold the rear planetary sun gear and turn the 1-way clutch.

  1. Make sure that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.



45. REMOVE REAR PLANETARY GEAR ASSEMBLY


    C067967
  1. Using a screwdriver, remove the snap ring.

  1. Remove the rear planetary gear assembly from the transaxle case.



46. REMOVE PLANETARY GEAR REAR THRUST NEEDLE ROLLER BEARING


    C068159
  1. Remove the thrust needle roller bearing and 2 bearing races from the rear planetary gear assembly.



47. REMOVE 1-WAY CLUTCH NO. 2


    C067966
  1. Separate the 2nd brake cylinder, 1-way clutch No. 2 and the rear planetary gear.



48. REMOVE OUTER RACE RETAINER


    C067965
  1. Remove the retainer from 1-way clutch No. 2.



49. REMOVE FRONT PLANETARY SUN GEAR


    C068157
  1. Remove the front planetary sun gear and thrust needle roller bearing from the transaxle case.



50. REMOVE 1ST AND REVERSE BRAKE DISC


    C067963
  1. Using a screwdriver, remove the snap ring.

  1. Remove the flange, 4 discs and 4 plates from the transaxle case.



51. REMOVE COUNTER DRIVE GEAR NUT


    C067960
  1. Fix the counter driven gear with the parking lock pawl.



    C067961E01
  1. Using SST and a hammer, release the lock washer.

    SST
    09930-00010  



    D025048E02
  1. Using SST, remove the nut and lock washer.

    SST
    09387-00121  



52. REMOVE PLANETARY GEAR ASSEMBLY


    D025047E01
  1. Using SST and a press, remove the planetary gear assembly from the transaxle case.

    SST
    09950-60010   (09951-00400, 09951-00320, 09952-06010)
    09950-70010   (09951-07100)



53. REMOVE COUNTER DRIVE GEAR


    C068474E01
  1. Install the 2 bolts onto the counter drive gear.

    Bolt (M6):
    L = 40 to 80 mm
    Pitch = 1.0 mm

  1. Rotate the 2 bolts and remove the counter drive gear and front planetary sun gear.

  1. Remove the 2 radial ball bearings from the counter drive gear and front planetary sun gear.



54. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    D008332E02
  1. Using SST, a press and a screwdriver, remove the snap ring.

    SST
    09387-00070  

  1. Remove the 1st and reverse brake return spring sub-assembly.



55. REMOVE 1ST AND REVERSE BRAKE PISTON NO. 2


    C068211
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the 1st and reverse brake piston.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a shop rag or piece of cloth.
    2. Do not splash ATF with the compressed air.



56. REMOVE 1ST AND REVERSE BRAKE PISTON NO. 2 O-RING


    C067962
  1. Remove the 2 O-rings from 1st and reverse brake piston No. 2.



57. REMOVE PARKING LOCK PAWL BRACKET


    C067957
  1. Remove the 3 bolts, cam guide and bracket from the transaxle case.



58. REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING


    C067956
  1. Remove the manual valve lever shaft retainer spring from the manual valve lever shaft.



59. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY


    C067954
  1. Using a screwdriver, release and remove the spacer.



    C067950
  1. Using a pin punch and hammer, drive out the manual valve lever shaft spring pin.

  1. Remove the manual valve lever shaft and manual valve lever.



60. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


    C067951
  1. Remove the parking lock rod from the manual valve lever.



61. REMOVE MANUAL VALVE LEVER SHAFT


    C067952
  1. Remove the manual valve lever shaft from the transaxle case.



62. REMOVE PARKING LOCK PAWL


    C067948
  1. Using a screwdriver, remove the parking lock pawl shaft from the transaxle case.

  1. Remove the parking lock pawl torsion spring and parking lock pawl from the transaxle case.



63. REMOVE COUNTER DRIVEN GEAR


    C068164
  1. Remove the counter driven gear, drive pinion and thrust needle roller bearing from the transaxle case.



64. REMOVE DIFFERENTIAL DRIVE PINION PLUG


    C068188
  1. Using a brass bar and a hammer, remove the differential drive pinion plug.



65. REMOVE DIFFERENTIAL DRIVE PINION


    D025174E01
  1. Using SST and a press, remove the differential drive pinion from the counter driven gear.

    SST
    09950-60010   (09951-00350)
    09950-70010   (09951-07150)



66. REMOVE BEARING LOCK PLATE


    C067770
  1. Remove the bolt and remove the bearing lock plate.



67. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE


    C068187
  1. Remove the differential gear lube apply tube from the transaxle housing.



68. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING


    C067771E02
  1. Using SST, remove the front drive pinion front tapered roller bearing from the transaxle housing.

    SST
    09308-10010  



69. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


    C067946E03
  1. Using SST, remove the front drive pinion rear tapered roller bearing from the transaxle case.

    SST
    09612-65014   (09612-01040)

  1. Remove transaxle case plate No. 1 from the transaxle case.



70. REMOVE COUNTER DRIVE GEAR BEARING


    D025049
  1. Remove the 2 counter drive gear bearing inner races RH from the transaxle case.

  1. Using SST, remove the counter drive gear bearing LH outer race from the transaxle case.

    SST
    09308-00010  



    D025050
  1. Using SST, remove the counter drive gear bearing rear outer race from the transaxle case.

    SST
    09308-00010  



71. REMOVE COUNTER DRIVE GEAR HOLE SNAP RING


    C067955
  1. Using a screwdriver, remove the counter drive gear hole snap ring from the transaxle case.



72. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


    C067953
  1. Using a screwdriver, remove the oil seal from the transaxle case.



73. REMOVE FRONT TRANSAXLE CASE OIL SEAL


    C067942E01
  1. Using SST and a hammer, remove the oil seal from the transaxle case.

    SST
    09950-60010   (09951-00550)
    09950-70010   (09951-07100)



74. REMOVE TRANSAXLE CASE OIL SEAL


    C067941E01
  1. Using SST and a hammer, remove the transaxle case oil seal from the transaxle housing.

    SST
    09950-60010   (09951-00530)
    09950-70010   (09951-07100)