Home › TRANSMISSION ยท U340E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > REASSEMBLY

for Preparation Click here



1. BEARING POSITION



C068166



2. INSPECT DIFFERENTIAL CASE TAPERED ROLLER BEARING PRELOAD


D025285E03
  1. Coat the front differential case and bearing with Toyota Genuine ATF WS or equivalent and install them onto the transaxle case.

  1. Install the transaxle housing with the 14 bolts.

    Torque:
    Bolt A:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }
    Bolt B:
    22 N*m{ 225 kgf*cm , 16 ft.*lbf }



    C081338E03
  1. Using SST and a small torque wrench, measure the preload of the differential gear.

    SST
    09564-32011  

    Preload:
    Bearing
    Standard
    New
    0.98 to 1.57 N*m (10.0 to 16.0 kgf*cm 8.7 to 13.9 in.*lbf)
    Used
    0.49 to 0.78 N*m (5.0 to 8.0 kgf*cm 4.3 to 6.9 in.*lbf)

    If the preload is not within the specifications, remove the differential from the transaxle case.
    Select a new transaxle case side adjusting shim in accordance with the following table.

    Adjusting Shim Thickness:
    Mark
    Thickness mm (in.)
    Mark
    Thickness mm (in.)
    01
    1.90 (0.0748)
    11
    2.40 (0.0945)
    02
    1.95 (0.0768)
    12
    2.45 (0.0965)
    03
    2.00 (0.0787)
    13
    2.50 (0.0984)
    04
    2.05 (0.0807)
    14
    2.55 (0.1004)
    05
    2.10 (0.0827)
    15
    2.60 (0.1024)
    06
    2.15 (0.0846)
    16
    2.65 (0.1043)
    07
    2.20 (0.0866)
    17
    2.70 (0.1063)
    08
    2.25 (0.0885)
    18
    2.75 (0.1082)
    09
    2.30 (0.0906)
    19
    2.80 (0.1102)
    10
    2.35 (0.0925)
    -
    -



3. INSTALL TRANSAXLE CASE OIL SEAL


    C068168E01
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, drive in a new oil seal.

    SST
    09554-14010  
    09950-70010   (09951-07100)

    Oil seal drive in depth:
    1.5 to 2.5 mm (0.059 to 0.098 in.)



4. INSTALL FRONT TRANSAXLE CASE OIL SEAL


    C068167E01
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, drive in a new oil seal.

    SST
    09726-27012   (09726-02041)
    09950-70010   (09951-07150)

    Oil seal drive in depth:
    5.4 to 6.4 mm (0.213 to 0.252 in.)



5. INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


    C125250E01
  1. Install transaxle case plate No. 1 onto the transaxle case.



    C068171E01
  1. Using SST and a hammer, install the front drive pinion rear tapered roller bearing onto the transaxle case.

    SST
    09950-60010   (09951-00610)
    09950-70010   (09951-07150)



6. INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING


    C068209E01
  1. Install the thrust bearing onto the transaxle housing.

  1. Using SST and a press, install a new front drive pinion front tapered roller bearing onto the transaxle housing.

    SST
    09950-60010   (09951-00650)
    09950-70010   (09951-07150)



7. INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE


    C068187
  1. Install the differential gear lube apply tube onto the transaxle housing.



8. INSTALL BEARING LOCK PLATE


    C067770
  1. Install the bearing lock plate onto the transaxle housing with the bolt.

    Torque:
    11 N*m{ 115 kgf*cm , 8 ft.*lbf }



9. INSTALL COUNTER DRIVE GEAR HOLE SNAP RING


    C067955
  1. Using a screwdriver, install the counter drive gear hole snap ring onto the transaxle case.



10. INSTALL COUNTER DRIVE GEAR BEARING


    C068173E01
  1. Using SST and a hammer, install the counter drive gear bearing LH outer race onto the transaxle case.

    SST
    09950-60020   (09951-00890)
    09950-70010   (09951-07150)



    C068172E01
  1. Using SST and a hammer, install the counter drive gear bearing RH outer race onto the transaxle case.

    SST
    09950-60020   (09951-00890)
    09950-70010   (09951-07150)

  1. Install the counter drive gear bearing onto the transaxle case.



11. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL


    C068174E01
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, install a new manual valve lever shaft oil seal.

    SST
    09950-60010   (09951-00220)
    09950-70010   (09951-07100)

    Oil seal drive in depth:
    -0.5 to 0.5 mm (-0.020 to 0.020 in.)



12. INSTALL DIFFERENTIAL DRIVE PINION


    D025175E01
  1. Using SST and a press, install the differential drive pinion onto the counter driven gear.

    SST
    09950-60010   (09951-00350)
    09950-70010   (09951-07150)

    NOTICE:
    When replacing the counter driven gear, replace the counter drive gear in the transaxle case as well.
    Press the differential drive pinion in until it comes into contact with the counter driven gear.



13. INSTALL FRONT DIFFERENTIAL DRIVE PINION PLUG


    D025176E01
  1. Using SST and a plastic hammer, install a new differential drive pinion plug onto the differential drive pinion.

    SST
    09221-25026   (09221-00071)

    Standard clearance:
    2.5 to 2.6 mm (0.0984 to 0.1023 in.)



14. INSTALL COUNTER DRIVEN GEAR


    C068165
  1. Install the counter driven gear and drive pinion thrust bearing onto the transaxle case.



15. INSTALL PARKING LOCK PAWL


    C067948
  1. Coat the parking lock pawl shaft with Toyota Genuine ATF WS.

  1. Install the parking lock pawl, parking lock pawl shaft torsion spring and parking lock pawl shaft onto the transaxle case.

    NOTICE:
    Check that the parking lock pawl moves smoothly.



16. INSTALL MANUAL VALVE LEVER SHAFT


    C067952
  1. Install the manual valve lever shaft onto the transaxle case.

    NOTICE:
    Do not damage the oil seal lip.



17. INSTALL PARKING LOCK ROD SUB-ASSEMBLY


    C067951
  1. Install the parking lock rod onto the manual valve lever.



18. INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY


    C067950
  1. Coat the manual valve lever sub-assembly with Toyota Genuine ATF WS.

  1. Install the manual valve lever and a new manual valve lever spacer onto the manual valve lever shaft.

  1. Using a pin punch and hammer, drive in the pin.



    C068175
  1. Turn the spacer and lever shaft to align the small hole for locating the staking position in the spacer with the staking position mark on the lever shaft.

  1. Using a pin punch, stake the spacer through the small hole.

  1. Check that the spacer does not turn.



19. INSTALL MANUAL VALVE LEVER SHAFT RETAINER SPRING


    C067956
  1. Install the manual valve lever shaft retainer spring onto the manual valve lever shaft.



20. INSTALL PARKING LOCK PAWL BRACKET


    C067957
  1. Install the parking lock pawl bracket, parking lock rod and cam guide sleeve onto the transaxle case with the 3 bolts.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }



21. INSTALL 1ST AND REVERSE BRAKE PISTON NO. 2 O-RING


    C067962
  1. Coat 2 new O-rings with Toyota Genuine ATF WS, and install them onto brake piston No. 2.



22. INSTALL 1ST AND REVERSE BRAKE PISTON NO. 2


    C068210
  1. Coat 1st and reverse brake piston No. 2 with Toyota Genuine ATF WS, and install it into the transaxle case.

    NOTICE:
    Do not damage the oil seal lip.



23. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    D008332E02
  1. Install the 1st and reverse brake return spring sub-assembly onto the transaxle case.

  1. Using SST, a press and a screwdriver, install the snap ring.

    SST
    09387-00070  



24. INSTALL COUNTER DRIVE GEAR


    D025054E01
  1. Using SST and a press, install the counter drive gear onto the transaxle case.

    SST
    09223-15030  
    09527-17011  
    09950-60010   (09951-00650)
    09950-70010   (09951-07150)



25. INSTALL PLANETARY GEAR ASSEMBLY


    D025053E01
  1. Using SST and a press, install the planetary gear assembly onto the transaxle case.

    SST
    09950-60010   (09951-00480)
    09223-15030  
    09527-17011  
    09950-70010   (09951-07150)



26. INSTALL COUNTER DRIVE GEAR NUT


    C067960
  1. Fix the counter driven gear with the parking lock pawl.



    C068178E01
  1. Using SST, install a new lock washer and nut.

    SST
    09387-00121  

    Torque:
    280 N*m{ 2,855 kgf*cm , 207 ft.*lbf }



    C068179E01
  1. Using SST and a small torque wrench, measure the rotating torque while turning the counter drive gear at 60 turns per minute.

    SST
    09387-00121  

    Rotating torque:
    0.20 to 0.49 N*m (2 to 5 kgf*cm, 2 to 4 in.*lbf)



    C068469E01
  1. Using SST and a hammer, stake the lock nut washer.

    SST
    09930-00010  



27. INSTALL 1ST AND REVERSE BRAKE DISC


    D025055E02
  1. Install the 4 plates, 4 discs and flange onto the transaxle case.

  1. Using a screwdriver, install the snap ring.



28. INSPECT PACK CLEARANCE OF FIRST AND REVERSE BRAKE


    C068184E01
  1. Using SST and a dial indicator, measure the first and reverse brake clearance while pressing the disc and plate from the rear side.

    SST
    09350-36010   (09350-06110)

    Pack clearance:
    0.806 to 1.206 mm (0.0317 to 0.0475 in.)

    NOTICE:
    If the clearance is outside the specifications, select a new brake flange.

    HINT:
    There are 4 different flange thicknesses.

    Flange thickness:
    Mark
    Thickness mm (in.)
    Mark
    Thickness mm (in.)
    -
    3.4 (0.134)
    2
    3.8 (0.150)
    1
    3.6 (0.142)
    3
    4.0 (0.157)

  1. Check that the 1st and reverse brake piston moves when compressed air (392 kPa, 4.0 kgf*cm2, 57 psi) is applied to the oil hole.



29. INSTALL FRONT PLANETARY SUN GEAR


    C068158
  1. Install the planetary sun gear and needle roller bearing onto the planetary gear assembly.



30. INSTALL OUTER RACE RETAINER


    C067965
  1. Install the outer retainer onto 1-way clutch No. 2.



31. INSTALL 1-WAY CLUTCH NO. 2


    C067966
  1. Install the 1-way clutch and 2nd brake piston assembly onto the rear planetary gear assembly.



32. INSTALL PLANETARY GEAR REAR THRUST NEEDLE ROLLER BEARING


    C068160
  1. Install thrust bearing race No. 2, the planetary gear thrust needle roller bearing and thrust bearing race onto the rear planetary gear assembly.



33. INSTALL REAR PLANETARY GEAR ASSEMBLY


    D025056
  1. Install the rear planetary gear assembly onto the transaxle case.

  1. Using a screwdriver, install the snap ring.



34. INSPECT 1-WAY CLUTCH NO. 2


    D025045E03
  1. Check that the rear planetary gear turns freely counterclockwise and locks when turned clockwise.



35. INSTALL 2ND BRAKE PISTON SLEEVE


    C067970
  1. Install the 2nd brake piston sleeve onto the transaxle case.



36. INSTALL 2ND BRAKE BRAKE DISC


    D025097E02
  1. Install the 3 discs, 3 plates and flange onto the transaxle case.

  1. Using a screwdriver, install a snap ring onto the transaxle case.



37. INSPECT PACK CLEARANCE OF 2ND BRAKE


    D025098
  1. Using a dial indicator, measure the 2nd brake pack clearance while applying and releasing compressed air (392 to 785 kPa, 4 to 8 kgf/cm2, 57 to 114 psi).

    Pack clearance:
    0.847 to 1.247 mm (0.0333 to 0.0491 in.)

    NOTICE:
    If the clearance is outside the specifications, select a new brake flange.

    HINT:
    There are 4 different flange thicknesses.

    Flange thickness:
    Mark
    Thickness mm (in.)
    Mark
    Thickness mm (in.)
    -
    3.0 (0.118)
    2
    3.4 (0.134)
    1
    3.2 (0.126)
    3
    3.6 (0.142)



38. INSTALL 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING


    C067971
  1. Using a screwdriver, install a snap ring onto the transaxle case.



39. INSTALL 1-WAY CLUTCH ASSEMBLY


    C068163
  1. Install thrust washer No. 2 onto the rear planetary gear assembly.

  1. Install 1-way clutch assembly onto the rear planetary sun gear assembly.



40. INSPECT 1-WAY CLUTCH ASSEMBLY


    D025044E07
  1. Hold the rear planetary sun gear and turn the 1-way clutch and check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.



41. INSTALL REAR PLANETARY SUN GEAR THRUST NEEDLE ROLLER BEARING


    C068162
  1. Install the thrust bearing and a washer onto the rear planetary sun gear.



42. INSTALL REAR PLANETARY SUN GEAR ASSEMBLY


    C067973
  1. Install the rear planetary sun gear assembly.



43. INSTALL REAR PLANETARY SUN GEAR NO. 2 THRUST NEEDLE ROLLER BEARING


    C068466
  1. Install the thrust bearing onto the rear planetary sun gear.



44. INSTALL DIRECT CLUTCH HUB


    C068196
  1. Install the direct clutch hub.



45. INSTALL THRUST NEEDLE ROLLER BEARING


    C068465
  1. Install thrust bearing race No. 3, the thrust needle roller bearing and the C-2 hub thrust bearing race onto the direct clutch hub.



46. INSTALL 2ND COAST AND OVERDRIVE BRAKE DISC


    D025099E02
  1. Install the 2 discs, 2 plates and flange onto the transaxle case.



47. INSTALL INTERMEDIATE SHAFT ASSEMBLY


    C067781
  1. Install the intermediate shaft assembly onto the transaxle case.



48. INSPECT 2ND COAST AND OVERDRIVE BRAKE CLEARANCE


    C068205
  1. As shown in the illustration, place a straight edge on the transaxle case and measure the distance between the 2nd coast and O/D brake flange and straight edge using vernier calipers. (Dimension A)



    C068206
  1. As shown in the illustration, place a straight edge on the O/D brake piston and measure the distance between the transaxle rear cover and straight edge using vernier calipers. (Dimension B)
    Calculate the piston stroke value using the following formula. Select a flange which meets the piston stroke value and install it.

    Pack clearance:
    2.091 to 2.491 mm (0.0823 to 0.0981 in.)

    NOTICE:
    If the clearance is outside the specifications, select a new brake flange.

    HINT:
    There are 4 different flange thicknesses.

    Flange thickness:
    Mark
    Thickness mm (in.)
    Mark
    Thickness mm (in,)
    4
    4.0 (0.1575)
    6
    4.4 (0.1732)
    5
    4.2 (0.1654)
    7
    4.6 (0.1811)



49. INSTALL REAR CLUTCH DRUM THRUST NEEDLE ROLLER BEARING


    C068467
  1. Install the bearing onto the intermediate shaft.



50. INSPECT INTERMEDIATE SHAFT ASSEMBLY


    C067778
  1. Install the transaxle rear cover with the 11 bolts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



    D025043
  1. Using a dial indicator, measure the clearance of the intermediate shaft.

    Standard clearance:
    0.204 to 0.966 mm (0.008 to 0.038 in.)

  1. Remove the 11 bolts and the transaxle rear cover.



51. INSTALL TRANSAXLE CASE GASKET


C067779
  1. Install 4 new gaskets onto the transaxle case.



52. INSTALL TRANSAXLE REAR COVER ASSEMBLY


    C068204
  1. Apply FIPG to the transaxle case.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent



    C067778
  1. Install the transaxle rear cover with the 11 bolts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



53. INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY


    C067777
  1. Install the forward clutch hub sub-assembly onto the transaxle case.



54. INSTALL FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING


    C068464
  1. Install the bearing onto the forward clutch hub.



55. INSTALL STATOR SHAFT THRUST NEEDLE ROLLER BEARING


    C067938
  1. Install the bearing onto the input shaft assembly.



56. INSTALL INPUT SHAFT ASSEMBLY


    C067775
  1. Install the input shaft assembly onto the transaxle case.



57. INSTALL OVERDRIVE BRAKE GASKET


    C067783
  1. Install 2 new gaskets onto the transaxle case.



58. INSTALL DIFFERENTIAL GEAR ASSEMBLY


    D025100
  1. Install the differential gear assembly onto the transaxle case.



59. INSTALL OIL PUMP ASSEMBLY


    C067773
  1. Install the oil pump with the 7 bolts.

    Torque:
    22 N*m{ 225 kgf*cm , 16 ft.*lbf }



60. INSPECT INPUT SHAFT ASSEMBLY


    C068186
  1. Make sure that the input shaft turns smoothly.



61. INSPECT INPUT SHAFT END PLAY


    C067772
  1. Measure the end play in the axial direction.

    End play:
    0.37 to 1.29 mm (0.0146 to 0.0508 in.)

    If the end play is not as specified, replace the thrust needle roller bearing.



62. INSTALL TRANSAXLE HOUSING


    C081344
  1. Apply FIPG to the transaxle case.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent



    D025285E01
  1. Install the transaxle housing with the 14 bolts.

    Torque:
    Bolt A:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }
    Bolt B:
    22 N*m{ 225 kgf*cm , 16 ft.*lbf }



63. INSTALL C-2 ACCUMULATOR PISTON


    D025040
  1. Coat 2 new O-rings with Toyota Genuine ATF WS and install them onto the C-2 accumulator piston.

    NOTICE:
    Do not damage the O-rings.



    C068839
  1. Install the spring and C-2 accumulator piston.

    Accumulator spring:
    Spring
    Free length/
    Outer diameter mm (in.)
    Color
    C-2
    66.90 (2.6339)
    17.20 (0.6772)
    -



64. INSTALL C-3 ACCUMULATOR PISTON


    D025039
  1. Coat 2 new O-rings with Toyota Genuine ATF WS and install them onto the C-3 accumulator piston.

    NOTICE:
    Do not damage the O-rings.



    C068840
  1. Install the spring and C-3 accumulator piston.

    Accumulator spring:
    Spring
    Free length/
    Outer diameter mm (in.)
    Color
    C-3
    80.20 (3.1575)
    18.70 (0.7362)
    Blue



65. INSTALL B-2 ACCUMULATOR PISTON


    D025038
  1. Coat 2 new O-rings with Toyota Genuine ATF WS and install them onto the B-2 accumulator piston.

    NOTICE:
    Do not damage the O-rings.



    C068841
  1. Install the spring and B-2 accumulator piston.

    Accumulator spring:
    Spring
    Free length/
    Outer diameter mm (in.)
    Color
    B-2
    66.90 (2.6339)
    15.50 (0.6102)
    Green



66. INSTALL CHECK BALL BODY


    C069422
  1. Install the spring and check ball body.



67. INSTALL BRAKE DRUM GASKET


    C067759
  1. Install a new brake drum gasket.



68. INSTALL TRANSAXLE CASE GASKET


    C067758
  1. Coat a new transaxle case gasket with Toyota Genuine ATF WS, and install it onto the transaxle case.



69. INSTALL TRANSAXLE CASE 2ND BRAKE GASKET


    C067757
  1. Coat a new transaxle case 2nd brake gasket with Toyota Genuine ATF WS, and install it onto the transaxle case.



70. INSTALL TRANSMISSION WIRE


    C067760
  1. Coat a new O-ring with Toyota Genuine ATF WS, and install it onto the transmission wire.



    D025102
  1. Insert the transmission wire into the transaxle.



    C062929
  1. Install the transmission wire with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



71. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


    C093940E11
  1. Align the groove of the manual valve with the pin of the manual valve lever.

  1. Provisionally install the valve body with the 13 bolts.

    Bolt length:
    Bolt A: 32 mm (1.26 in.)
    Bolt B: 22 mm (0.87 in.)
    Bolt C: 55 mm (2.17 in.)
    Bolt D: 45 mm (1.77 in.)



    C093939E08
  1. Provisionally install the detent spring and detent spring cover with the 2 bolts.

    Bolt length:
    Bolt A: 14 mm (0.55 in.)
    Bolt B: 45 mm (1.77 in.)

  1. Check that the manual valve lever is in contact with the center of the roller at the tip of the detent spring.

  1. Tighten the 15 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }



    C093938E05
  1. Connect the 5 solenoid connectors.

  1. Install the ATF temperature sensor with the lock plate and bolt.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    Bolt length:
    55 mm (2.17 in.)



72. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


    D005904E04
  1. Coat a new O-ring with Toyota Genuine ATF WS, and install it into the oil strainer.



    C062685
  1. Install the valve body oil strainer assembly onto the automatic transaxle with the 3 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }



73. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


    D025104
  1. Install the 2 magnets onto the oil pan.

  1. Install a new oil pan gasket onto the oil pan.



    C062684
  1. Install the oil pan with the 19 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }



74. INSTALL BREATHER PLUG HOSE


    C067752
  1. Install the breather plug hose onto the transaxle case.



75. INSTALL TRANSAXLE CASE NO. 1 PLUG


    C067754
  1. Coat 5 new O-rings with Toyota Genuine ATF WS, and install them onto the screw plugs.

  1. Install the 4 screw plugs onto the transaxle housing and transaxle case.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



    C067755
  1. Install the screw plug onto the transaxle case.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



76. INSTALL OIL COOLER TUBE UNION


    D025286
  1. Coat 2 new O-rings with Toyota Genuine ATF WS, and install them into the 2 oil cooler tube unions.

  1. Install the 2 oil cooler tube unions onto the transaxle case.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



77. INSTALL TRANSMISSION REVOLUTION SENSOR


    C067751
  1. Coat a new O-ring with Toyota Genuine ATF WS, and install it into the transmission revolution sensor.

  1. Install the transmission revolution sensor onto the transaxle case with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



78. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C117107E01
  1. Install the park/neutral position switch assembly onto the manual transaxle.

  1. Provisionally install the 2 bolts.

  1. Replace the lock plate with a new one and tighten the manual valve shaft nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Provisionally install the control shaft lever.



    C117103
  1. Turn the lever counterclockwise until it stops, then turn it clockwise 2 notches.

  1. Remove the control shaft lever.



    C117107E02
  1. Align the groove with the neutral basic line.

  1. Hold the switch in this position and tighten the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



    C117105
  1. Using a screwdriver, stake the nut with the lock plate.



    C117101
  1. Install the control shaft lever with the nut and washer.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



79. INSTALL SPEEDOMETER DRIVEN HOLE COVER


    C121659
  1. Coat a new O-ring with Toyota Genuine ATF WS and install it into the speedometer driven hole cover.

  1. Install the speedometer driven hole cover onto the transaxle housing.