Home › RESTRAINTS › SEAT BELT › REAR CENTER SEAT OUTER BELT ASSEMBLY (for Hatchback 5 Door)

REAR CENTER SEAT OUTER BELT ASSEMBLY (for Hatchback 5 Door) > INSTALLATION

for Preparation Click here


CAUTION:
Always use "TORX" socket wrench E10 when installing the rear seat.



1. INSTALL REAR SEAT SHOULDER BELT COVER


    B114466
  1. Engage the 2 claws and install the rear seat shoulder belt cover.



2. INSTALL ROOF HEADLINING ASSEMBLY


    B114465
  1. Install the roof headlining with the clip.



3. INSTALL SEAT BELT ANCHOR COVER


    B114467
  1. Engage the 4 claws and install the seat belt anchor cover.



4. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY


    B114437E01
  1. Check the angle of inclination required to lock the retractor.

    1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15°or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45°or more.

      NOTICE:
      Do not disassemble the retractor.

      If the operation is not as specified, replace the rear seat outer belt.



    B114551
  1. Hook the lower stay of the retractor onto the 2 body hooks and install the retractor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }



    B114463
  1. Install the bracket with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. Check that the ELR locks.

    NOTICE:
    Perform the check with the rear center seat outer belt installed.


    1. With the belt installed, check that the belt locks when it is pulled out quickly.
      If the operation is not as specified, replace the rear center seat outer belt.



    B114461
  1. Install the through anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }



    B114469
  1. Engage the 2 claws and close the slip joint cover.



    B114459
  1. Install the 2 tongue plates.



5. INSTALL ROOF SIDE INNER GARNISH RH


    B114576E01
  1. w/ Curtain Shield Airbag:

    1. Install a new special clip.

    2. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.

    3. Engage the 5 clips and install the roof side inner garnish.



    B114575
  1. w/o Curtain Shield Airbag:

    1. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.

    2. Engage the 5 clips and install the roof side inner garnish.



    B114468
  1. Engage the 4 claws and install the center belt guide.



6. INSTALL ROOF SIDE INNER GARNISH LH


    B114578E01
  1. w/ Curtain Shield Airbag:

    1. Install a new special clip onto the roof side inner garnish.

    2. Pass the rear seat outer belt through the slit in the roof side inner garnish.

    3. Engage the 5 clips and install the roof side inner garnish.



    B114577
  1. w/ Curtain Shield Airbag:

    1. Pass the rear seat outer belt through the slit in the roof side inner garnish.

    2. Engage the 5 clips and install the roof side inner garnish.



7. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH


    B114573
  1. w/ Package Tray Trim:

    1. Engage the 3 clips and the 6 claws and install the deck trim side panel.

    2. Tighten the 3 screws.



    B114290
  1. w/o Package Tray Trim:

    1. Engage the 4 clips and the 6 claws and install the deck trim side panel.

    2. Tighten the 2 screws.



8. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    B114574
  1. w/ Package Tray Trim:

    1. w/ Luggage Compartment Room Light:

      1. Connect the luggage compartment room light connector.
      2. Engage the 3 clips and the 6 claws and install the deck trim side board.
      3. Tighten the 3 screws.

    2. w/o Luggage Compartment Room Light:

      1. Engage the 3 clips and the 6 claws and install the deck trim side board.
      2. Tighten the 3 screws.



    B114291
  1. w/o Package Tray Trim:

    1. w/ Luggage Compartment Room Light:

      1. Connect the luggage compartment room light connector.
      2. Engage the 4 clips and the 6 claws and install the deck trim side board.
      3. Tighten the 2 screws.

    2. w/o Luggage Compartment Room Light:

      1. Engage the 4 clips and the 6 claws and install the deck trim side board.
      2. Tighten the 2 screws.



9. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH


    B130498
  1. Engage the clip and install the anchor plate.

  1. Tighten the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }



    B114289
  1. Install the belt.



10. INSTALL REAR SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



11. INSTALL REAR DECK TRIM COVER


    B114283
  1. for Grand Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.



    B117692
  1. for Temper Spare Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.



12. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B114431
  1. Install the rear door opening trim weatherstrip.



13. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



14. INSTALL REAR DOOR SCUFF PLATE RH


    B114287
  1. Engage the 6 claws and install the rear door scuff plate.



15. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



16. INSTALL REAR SEAT ASSEMBLY RH


    B114684E01
  1. Insert the 2 location pins through the 2 body holes and install the rear seat.

  1. Using "TORX" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



    B114660E01
  1. Install the rear seat cushion.

  1. Using "TORX" socket wrench E10, install the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



17. INSTALL REAR SEAT ASSEMBLY LH


    B126922E01
  1. Insert the 2 location pins through the 2 body holes and install the rear seat.

  1. Using "TORX" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



    B114740E01
  1. Install the rear seat cushion.

  1. Using "TORX" socket wrench E10, install the 3 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



18. INSTALL NO. 1 REAR SEAT LEG COVER
  1. for RH Side:

    1. Install the No. 1 rear seat leg cover .

  1. for LH Side:

    1. Install the No. 1 rear seat leg cover .



19. INSTALL NO. 2 REAR SEAT LEG COVER


    B114739
  1. Engage the 3 claws and install the No. 2 rear seat leg cover.



20. INSTALL DECK FLOOR BOX RH (w/ Deck Board)


    B106446
  1. Set the deck floor box and lock the 2 knobs.



21. INSTALL DECK FLOOR BOX LH (w/ Deck Board)

HINT:
Use the same procedure as for the RH side.



22. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)


    B119913
  1. Install the spare wheel cover.



23. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board)


    B106447
  1. Set the deck board and lock the 2 knobs.



24. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)


    B119912
  1. Install the rear floor carpet.



25. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)


    B114569E01
  1. Engage the 2 claws and install the package tray trim panel.

  1. Install the 5 pieces of hook tape.

  1. Install the 2 package tray trim suspenders.



26. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Luggage Compartment Room Light)

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }