REAR CENTER SEAT OUTER BELT ASSEMBLY (for Hatchback 5 Door) > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Luggage Compartment Room Light) |
| 2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim) |
![]() |
Remove the 2 package tray trim suspenders.
Remove the 5 pieces of hook tape.
Disengage the 2 claws and remove the package tray trim.
| 3. REMOVE DECK BOARD SUB-ASSEMBLY (w/ Deck Board) |
![]() |
Release the 2 knobs and remove the deck board.
| 4. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Deck Board) |
![]() |
Remove the spare wheel cover.
| 5. REMOVE DECK FLOOR BOX RH (w/ Deck Board) |
![]() |
Release the 2 knobs and remove the deck floor box.
| 6. REMOVE DECK FLOOR BOX LH (w/ Deck Board) |
| 7. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Deck Board) |
![]() |
Remove the rear floor carpet.
| 8. REMOVE NO. 1 REAR SEAT LEG COVER |
for RH Side:
Remove the No. 1 rear seat leg cover .
for LH Side:
Remove the No. 1 rear seat leg cover .
| 9. REMOVE NO. 2 REAR SEAT LEG COVER |
![]() |
Disengage the 3 claws in the sequence shown in the illustration and remove the No. 1 rear seat leg cover.
| 10. REMOVE REAR SEAT ASSEMBLY RH |
![]() |
Using "TORX" socket wrench E10, remove the 2 bolts and pull up the rear seat cushion.
![]() |
Using "TORX" socket wrench E10, remove the 4 bolts and the rear seat.
| 11. REMOVE REAR SEAT ASSEMBLY LH |
![]() |
Using "TORX" socket wrench E10, remove the 3 bolts and pull up the rear seat cushion.
![]() |
Using "TORX" socket wrench E10, remove the 4 bolts and the rear seat.
| 12. REMOVE REAR DOOR SCUFF PLATE RH |
![]() |
Disengage the 6 claws and remove the rear door scuff plate.
| 13. REMOVE REAR DOOR SCUFF PLATE LH |
| 14. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Remove the rear door opening trim weatherstrip to the extent that the deck trim side panel and roof side inner garnish can be removed.
| 15. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH |
| 16. REMOVE REAR DECK TRIM COVER |
![]() |
for Temper Spare Tire:
Using a clip remover, remove the 2 clips.
Disengage the 8 claws and remove the rear deck trim cover.
![]() |
for Grand Tire:
Using a clip remover, remove the 2 clips.
Disengage the 8 claws and remove the rear deck trim cover.
| 17. REMOVE REAR SEAT OUTER BELT ASSEMBLY RH |
![]() |
Remove the belt.
![]() |
Remove the bolt.
Disengage the clip and remove the anchor plate.
| 18. REMOVE REAR SEAT OUTER BELT ASSEMBLY LH |
| 19. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH |
![]() |
w/ Package Tray Trim:
Remove the 3 screws.
Disengage the 3 clips and the 6 claws and remove the deck trim side panel.
![]() |
w/o Package Tray Trim:
Remove the 3 screws.
Disengage the 4 clips and the 6 claws and remove the deck trim side panel.
| 20. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH |
![]() |
w/ Package Tray Trim:
w/ Luggage Compartment Room Light:
w/o Luggage Compartment Room Light:
![]() |
w/o Package Tray Trim:
w/ Luggage Compartment Room Light:
w/o Luggage Compartment Room Light:
| 21. REMOVE ROOF SIDE INNER GARNISH RH |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the center belt guide.
![]() |
w/ Curtain Shield Airbag:
Disengage the 5 clips.
Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
![]() |
w/o Curtain Shield Airbag:
Disengage the 5 clips.
Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
| 22. REMOVE ROOF SIDE INNER GARNISH LH |
![]() |
w/ Curtain Shield Airbag:
Disengage the 5 clips.
Pass the rear seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
![]() |
w/o Curtain Shield Airbag:
Disengage the 5 clips.
Pass the rear seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
| 23. REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY |
![]() |
Remove the 2 tongue plates.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and open the slip joint cover.
![]() |
Remove the bolt and the through anchor.
![]() |
Remove the bolt, the hook and the bracket.
![]() |
Remove the bolt, the 2 hooks and the retractor.
| 24. REMOVE SEAT BELT ANCHOR COVER |
![]() |
Using a moulding remover, disengage the 4 claws and remove the seat belt anchor cover.
| 25. REMOVE ROOF HEADLINING ASSEMBLY |
![]() |
Using a clip remover, remove the clip and the roof headlining.
| 26. REMOVE REAR SEAT SHOULDER BELT COVER |
![]() |
Disengage the 2 claws and remove the rear seat shoulder belt cover.