Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Hatchback)

FRONT SEAT ASSEMBLY (for Hatchback) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp surfaces on the front seat adjuster frame could cause injuries to your hands.

HINT:
The procedure described below is for the driver side of LHD. Use the same procedure for both the front passenger and driver sides of LHD, unless otherwise specified.



1. INSTALL FRONT SEAT CUSHION LOWER SHIELD LH


    B127735
  1. for 6 Way Type:

    1. Engage the claw and install the front seat cushion lower shield.

    2. Tighten the screw.



    B127737
  1. for 4 Way Type:

    1. Engage the claw and install the front seat cushion lower shield.

    2. Tighten the screw.



2. INSTALL FRONT SEAT CUSHION LOWER SHIELD RH


    B127734
  1. for 6 Way Type:

    1. Engage the 2 claws and install the front seat cushion lower shield.

    2. Tighten the screw.



    B127736
  1. for 4 Way Type:

    1. Engage the claw and install the front seat cushion shield lower.

    2. Tighten the screw.



3. INSTALL RECLINING ADJUSTER OUTSIDE COVER LH


    B114709
  1. Install the reclining adjuster outside cover with the screw.



4. INSTALL RECLINING ADJUSTER OUTSIDE COVER RH

HINT:
Use the same procedure as for the LH side.



5. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    B127699
  1. for Full Memory Type:

    1. Engage the 2 claws and install the reclining adjuster inside cover.

    2. Tighten the screw.



    B114710
  1. for Normal Type:

    1. Engage the claw and install the reclining adjuster inside cover.

    2. Tighten the screw.



6. INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedure as for the LH side.



7. INSTALL VERTICAL ADJUSTER SPACER (for Driver Side)


    B119878
  1. Engage the claw and install the vertical adjuster spacer.



8. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)


    B114708
  1. Install the front seat side airbag with the 2 nuts.

    Torque:
    5.5 N*m{ 55 kgf*cm , 49 in.*lbf }



    B114707
  1. Install the 2 wire harness clamps.



    B119877
  1. Install the 3 wire harness clamps and the airbag connector.



9. INSTALL FRONT SEATBACK COVER PAD


B114713
  1. Install the front seatback cover pad.

    NOTICE:
    The fabrc for fixing the airbag must mot be wrinkled when installing the front seat back cover pad (w/ Front Seat Side Airbag).



    B114714E01
  1. Using hog ring pliers, install 3 new hog rings as shown in the illustration.



10. INSTALL FRONT SEAT HEADREST SUPPORT


B114715E03

HINT:
Use the same procedure for both sides.

  1. Align the protruding portion of the front seat headrest support with the installation groove of the front seat adjuster frame.

  1. Engage the 2 claws and install the front seat headrest support.



11. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL (for Walk in Seat Type)


    B121715
  1. Engage the 4 claws and install the reclining remote control lever bezel.



12. INSTALL RECLINING REMOTE CONTROL LEVER (for Walk in Seat Type)


    B121733
  1. Engage the claw and install the reclining remote control lever.



13. INSTALL FRONT SEAT CUSHION COVER PAD


B209763
  1. Engage the 2 claws and the 6 hooks and install the front seat cushion cover pad.

  1. for Front Passenger Side:

    1. Install the occupant detection sensor connector.



    B114700E02
  1. w/ Front Seat Side Airbag:

    1. Fix the front seat side airbag wire harness with the front seat cushion cover pad fixing cover.

  1. for Clip Type:

    1. Install the 2 clips.

  1. for J Hook Type:

    1. Engage the 2 hooks.



    B119875
  1. Install the front seatback cover band.



14. INSTALL FRONT SEAT CUSHION SHIELD RH


    B114698
  1. Engage the claw and the clip and install the front seat cushion shield.

  1. Tighten the screw.



15. INSTALL FRONT SEAT INNER BELT ASSEMBLY


    B114767E01
  1. for Driver Side:

    1. Install the front seat inner belt with the bolt.

      Torque:
      42 N*m{ 430 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not place the front seat inner belt over the convex areas of the front seat frame adjuster.

    2. Install the wire harness into the claw of the front seat cushion shield.



    3. B209777
    4. Install the 4 clamps.

    5. Install the buckle switch connector.

    6. Engage the 2 hooks and install the front seat cushion cover.



    B114763E01
  1. for Front Passenger Side:

    1. Install the front seat inner belt with the bolt.

      Torque:
      42 N*m{ 430 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not place the front seat inner belt over the convex areas of the front seat frame adjuster.

    2. Install the wire harness into the claw of the front seat cushion shield.



    3. B209774
    4. Install the 5 clamps.

    5. Install the buckle switch connector.

    6. Connect the occupant detection sensor connector.

    7. Engage the 2 hooks and install the front seat cushion cover.



16. INSTALL FRONT SEAT CUSHION SHIELD LH


    B114697
  1. Engage the 2 claws and the clip and install the front seat cushion shield.

  1. Tighten the screw.



17. INSTALL RECLINING ADJUSTER RELEASE HANDLE


    B114716
  1. Engage the claw and install the reclining adjuster release handle.



18. INSTALL VERTICAL ADJUSTER HANDLE (for Driver Side)


    B119874
  1. Install the vertical adjuster handle with the 2 screws.



19. INSTALL VERTICAL ADJUSTER COVER (for Driver Side)


    B119881
  1. Engage the 3 claws and install the vertical adjuster cover.