Home › TRANSMISSION ยท C54 MANUAL TRANSAXLE › OUTPUT SHAFT

OUTPUT SHAFT > DISASSEMBLY

for Preparation Click here



1. INSPECT 1ST GEAR THRUST CLEARANCE


C080538
  1. Using a feeler gauge, measure the 1st gear thrust clearance.

    Standard clearance:
    0.10 to 0.40 mm (0.0039 to 0.0157 in.)

    Maximum clearance:
    0.40 mm (0.0157 in.)

    If the clearance exceeds the maximum, replace the 1st gear thrust washer, 1st gear or transmission clutch hub No. 1.



2. INSPECT 2ND GEAR THRUST CLEARANCE


C068312
  1. Using a dial gauge, measure the 2nd gear thrust clearance.

    Standard clearance:
    0.10 to 0.55 mm (0.0039 to 0.0217 in.)

    Maximum clearance:
    0.55 mm (0.0217 in.)

    If the clearance exceeds the maximum, replace transmission clutch hub No. 1, 2nd gear or 3rd driven gear.



3. INSPECT 1ST GEAR RADIAL CLEARANCE


C068309
  1. Using a dial gauge, measure the 1st gear radial clearance between the gear and shaft.

    Standard clearance:
    KOYO made bearing:
    0.015 to 0.058 mm (0.0006 to 0.0023 in.)
    NSK made bearing:
    0.015 to 0.056 mm (0.0006 to 0.0022 in.)

    Maximum clearance:
    KOYO made:
    0.058 mm (0.0023 in.)
    NSK made:
    0.056 mm (0.0022 in.)

    If the clearance exceeds the maximum, replace the 1st gear or 1st gear needle roller bearing.



4. INSPECT 2ND GEAR RADIAL CLEARANCE


C068254
  1. Using a dial gauge, measure the 2nd gear radial clearance between the gear and shaft.

    Standard clearance:
    KOYO made:
    0.015 to 0.058 mm (0.0006 to 0.0023 in.)
    NSK made:
    0.015 to 0.056 mm (0.0006 to 0.0022 in.)

    Maximum clearance:
    KOYO made:
    0.058 mm (0.0023 in.)
    NSK made:
    0.056 mm (0.0022 in.)

    If the clearance exceeds the maximum, replace the 2nd gear or 2nd gear needle roller bearing.



5. REMOVE 4TH DRIVEN GEAR


C080539E02
  1. Using SST and a press, remove the output shaft rear bearing and 4th driven gear from the output shaft.

    SST
    09950-00020  



6. REMOVE OUTPUT GEAR SPACER


C068005
  1. Remove the output gear spacer from the output shaft.



7. REMOVE 2ND GEAR


G027264E02
  1. Using SST and a press, remove the 3rd driven gear with 2nd gear from the output shaft.

    SST
    09950-00020  



8. REMOVE 2ND GEAR NEEDLE ROLLER BEARING


C080541
  1. Remove the 2nd gear needle roller bearing and 2nd gear bearing spacer from the output shaft.



9. REMOVE SYNCHRONIZER RING NO.1 (FOR 2ND GEAR)


C120730
  1. Remove synchronizer ring No. 1 from the output shaft.



10. REMOVE 1ST GEAR


C080543
  1. Using 2 screwdrivers and a hammer, remove the clutch hub No. 1 shaft snap ring from the output shaft.

    HINT:
    Use a piece of cloth to keep the shaft snap ring from flying off.



    C080544E02
  1. Using SST and a press, remove the clutch hub No. 1 assembly and 1st gear from the output shaft.

    SST
    09950-00020  

    NOTICE:
    1. Do not tighten SST excessively.
    2. Support the input shaft by hand to prevent it from dropping off.



11. REMOVE SYNCHRONIZER RING GEAR NO.1 (FOR 1ST GEAR)


C080465
  1. Remove synchronizer ring No. 1 from the 1st gear.



12. REMOVE 1ST GEAR NEEDLE ROLLER BEARING


C068012
  1. Remove the 1st gear needle roller bearing from the output shaft.



13. REMOVE 1ST GEAR THRUST WASHER


C068013
  1. Remove the 1st gear thrust washer from the output shaft.



14. REMOVE 1ST GEAR THRUST WASHER PIN OR BALL


C068014
  1. Remove the 1st gear thrust washer pin or ball from the output shaft.



15. REMOVE REVERSE GEAR


C068015
  1. Remove the reverse gear, 3 synchromesh shifting keys and 3 synchromesh shifting key springs from transmission clutch hub No. 1.

    NOTICE:
    Use a piece of cloth to keep the shifting key and shifting key spring from flying off.