Home › SUSPENSION & AXLE › SUSPENSION › FRONT SHOCK ABSORBER WITH COIL SPRING (for Hatchback)

FRONT SHOCK ABSORBER WITH COIL SPRING (for Hatchback) > REMOVAL

for Preparation Click here



1. REMOVE FRONT WIPER ARM HEAD CAP


E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.



2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113850
  1. Remove the nut and front wiper arm.



3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



4. REMOVE HOOD TO COWL TOP SEAL


E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.



5. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.



    E113852
  1. Disconnect the washer hose.

  1. Disengage the 11 claws and clip.



    E113854
  1. Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.



6. REMOVE COWL TOP VENTILATOR LOUVER LH (for LHD)


E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.



7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.



8. REMOVE COWL TOP VENTILATOR LOUVER LH (for RHD)


E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.



9. REMOVE FRONT WIPER MOTOR AND LINK


E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.



10. REMOVE COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2


A108437
  1. Disengage the claw and remove cowl to register duct sub-assembly No. 2.



11. REMOVE COWL TOP PANEL OUTER


A108438
  1. Disengage the wire harness clamp.



    A115392
  1. Remove the 9 bolts and remove the cowl top panel outer.



12. REMOVE FRONT WHEEL


13. SEPARATE FRONT STABILIZER LINK ASSEMBLY


C125276
  1. Remove the nut and separate the stabilizer link from the shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.



14. SEPARATE FRONT FLEXIBLE HOSE (w/ ABS)


C125274
  1. Remove the bolt and separate the speed sensor and flexible hose.



15. SEPARATE FRONT FLEXIBLE HOSE (w/o ABS)


C186418
  1. Remove the bolt and separate the flexible hose.



16. REMOVE FRONT SUSPENSION SUPPORT DUST COVER


17. REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING


C125277
  1. Remove the 2 nuts and 2 bolts and separate the shock absorber with coil spring from the steering knuckle.

    HINT:
    Keep the bolt from rotating while loosening and removing the nuts.



    C107504
  1. Using a socket hexagon wrench 6, fix the shock absorber rod and remove the nut.

  1. Remove the No. 2 suspension support.

  1. Remove the front shock absorber with coil spring from the vehicle.