Home › SUSPENSION & AXLE › SUSPENSION › FRONT SHOCK ABSORBER WITH COIL SPRING (for Sedan)

FRONT SHOCK ABSORBER WITH COIL SPRING (for Sedan) > REMOVAL

for Preparation Click here



1. REMOVE FRONT WIPER ARM HEAD CAP


    E127832E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.



2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E127833
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. Remove the nut and front wiper arm.



3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



4. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E127834E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.



5. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


    E127838
  1. Disengage the 3 clips, the 4 claws and the 8 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.



    E127839
  1. Disconnect the washer hoses.

  1. Disengage the 5 hooks.



7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


    E127835
  1. Disengage the 2 clips, the 6 claws and the 10 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.



    E127836
  1. Disconnect the washer hoses.

  1. Disengage the 5 hooks.



8. REMOVE FRONT WIPER MOTOR AND LINK


    E127837
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.



9. REMOVE FRONT AIR SHUTTER SEAL


A133324
  1. Disengage the 3 claws and remove the front air shutter seal.



10. REMOVE COWL TOP PANEL OUTER


A128446
  1. Disengage the wire harness clamp.



    A128447
  1. Remove the 2 bolts and remove the cowl top to cowl inner brace.



    A128448
  1. Remove the 8 bolts and remove the cowl top panel outer.



11. REMOVE FRONT WHEEL


12. SEPARATE FRONT STABILIZER LINK ASSEMBLY


C125276
  1. Remove the nut and separate the stabilizer link from the shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.



13. SEPARATE FRONT FLEXIBLE HOSE (w/ ABS)


C125274
  1. Remove the bolt and separate the speed sensor and flexible hose.



14. SEPARATE FRONT FLEXIBLE HOSE (w/o ABS)
  1. Remove the bolt and separate the flexible hose.



15. REMOVE FRONT SUSPENSION SUPPORT DUST COVER


16. REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING


C125277
  1. Remove the 2 nuts and 2 bolts and separate the shock absorber with coil spring from the steering knuckle.

    HINT:
    Keep the bolt from rotating while loosening and removing the nuts.



    C107504
  1. Using a socket hexagon wrench 6, fix the shock absorber rod and remove the nut.

  1. Remove the No. 2 suspension support.

  1. Remove the front shock absorber with coil spring from the vehicle.