REAR SEAT OUTER BELT ASSEMBLY (for Hatchback 3 Door Bench Seat Type) > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for LH Side) |
| 2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY |
![]() |
Remove the 2 package tray trim suspenders.
Remove the 5 pieces of hook tape.
Disengage the 2 claws and remove the package tray trim.
| 3. REMOVE DECK BOARD SUB-ASSEMBLY |
![]() |
Release the 2 knobs and remove the deck board.
| 4. REMOVE DECK FLOOR BOX RH |
![]() |
Release the 2 knobs and remove the deck floor box.
| 5. REMOVE DECK FLOOR BOX LH |
| 6. REMOVE REAR SEAT CUSHION COVER PAD |
![]() |
Hold the front edge of the rear seat cushion and lift it up, as shown in the illustration, to disengage the the 2 rear seat cushion lock hooks.
Pass the rear seat inner belt through the slit in the rear seat cushion, disengage the hook between the rear seat cushion and rear seat back, and remove the rear seat cushion.
| 7. REMOVE REAR SEAT BACK ASSEMBLY |
![]() |
Using "TORX" socket wrench E10, remove the 4 bolts and the rear seat back.
| 8. REMOVE FRONT DOOR SCUFF PLATE |
![]() |
Using "TORX" socket wrench E10, remove the 2 bolts and pull up the rear seat cushion.
![]() |
Using "TORX" socket wrench E10, remove the 4 bolts and the rear seat.
| 9. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP |
![]() |
Remove the front door opening trim weatherstrip.
| 10. REMOVE REAR SEAT SHOULDER BELT HANGER |
![]() |
Remove the belt of the rear seat outer belt.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the rear seat shoulder belt hanger.
| 11. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY |
![]() |
Disengage the 8 clips, the retainer and the 10 claws and remove the front quarter trim panel.
| 12. REMOVE REAR DECK TRIM COVER |
![]() |
for Temper Spare Tire:
Using a clip remover, remove the 2 clips.
Disengage the 8 claws and remove the rear deck trim cover.
![]() |
for Grand Tire:
Using a clip remover, remove the 2 clips.
Disengage the 8 claws and remove the rear deck trim cover.
| 13. REMOVE DECK TRIM SIDE PANEL ASSEMBLY |
![]() |
Remove the bolt.
Disengage the clip and remove the anchor plate of the rear seat outer belt.
![]() |
for RH Side:
Remove the 3 screws.
Disengage the 3 clips and the 3 claws and remove the deck trim side panel.
![]() |
for LH Side:
Remove the 3 screws.
Disengage the 3 clips and the 3 claws.
Disconnect the luggage compartment room light connector and remove the deck trim side panel.
| 14. REMOVE ROOF SIDE INNER GARNISH |
![]() |
for RH Side (w/ Curtain Shield Airbag):
Disengage the 4 clips and the claw.
Pass the rear seat outer and rear center seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
![]() |
for RH Side (w/o Curtain Shield Airbag):
Disengage the 4 clips and the claw.
Pass the rear seat outer and rear center seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
![]() |
for LH Side (w/ Curtain Shield Airbag):
Disengage the 4 clips and the claw.
Pass the rear seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
![]() |
for LH Side (w/o Curtain Shield Airbag):
Disengage the 4 clips and the claw.
Pass the rear seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
| 15. REMOVE REAR SEAT OUTER BELT ASSEMBLY |
![]() |
Remove the bolt and the through anchor.
![]() |
Remove the bolt, the 2 hooks and the retractor.
| 16. REMOVE SEAT BELT HOLE SEAL |
![]() |
Disengage the 2 claws and remove the seat belt hole seal.