REAR CENTER SEAT OUTER BELT ASSEMBLY (for Hatchback 3 Door) > INSTALLATION |
| 1. INSTALL REAR SEAT SHOULDER BELT COVER |
![]() |
Engage the 2 claws and install the rear seat shoulder belt cover.
| 2. INSTALL ROOF HEADLINING ASSEMBLY |
![]() |
Install the roof headlining with the clip.
| 3. INSTALL SEAT BELT ANCHOR COVER |
![]() |
Engage the 4 claws and install the seat belt anchor cover.
| 4. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY |
![]() |
Check the angle of inclination required to lock the retractor.
Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15°or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45°or more.
![]() |
Hook the lower stay of the retractor onto the 2 body hooks and install the retractor with the bolt.
![]() |
Install the bracket with the bolt.
Check that the ELR locks.
With the belt installed, check that the belt locks when it is pulled out quickly.
If the operation is not as specified, replace the rear center seat outer belt.
![]() |
Install the through anchor with the bolt.
![]() |
Engage the 2 claws and close the slip joint cover.
![]() |
Install the 2 tongue plates.
| 5. INSTALL ROOF SIDE INNER GARNISH RH |
![]() |
w/ Curtain Shield Airbag:
Install a new special clip onto the roof side inner garnish.
Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.
Engage the 4 clips and the claw and install the roof side inner garnish.
![]() |
w/o Curtain Shield Airbag:
Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.
Engage the 4 clips and the claw and install the roof side inner garnish.
![]() |
Engage the 4 claws and install the center belt guide.
| 6. INSTALL ROOF SIDE INNER GARNISH LH |
![]() |
w/ Curtain Shield Airbag:
Install a new special clip onto the roof side inner garnish.
Pass the rear seat outer belt through the slit in the roof side inner garnish.
Engage the 4 clips and the claw and install the roof side inner garnish.
![]() |
w/o Curtain Shield Airbag:
Pass the rear seat outer belt through the slit in the roof side inner garnish.
Engage the 4 clips and the claw and install the roof side inner garnish.
| 7. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH |
![]() |
Engage the 3 clips and the 3 claws and install the deck side trim panel.
Tighten the 3 screws.
| 8. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH |
![]() |
Connect the deck side room light connector.
Engage the 3 clips and the 3 claws and install the deck side trim panel.
Tighten the 3 screws.
| 9. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH |
![]() |
Engage the clip and install the anchor plate.
Tighten the bolt.
| 10. INSTALL REAR SEAT OUTER BELT ASSEMBLY LH |
| 11. INSTALL REAR DECK TRIM COVER |
![]() |
for Grand Tire:
Engage the 8 claws and install the rear deck trim cover.
Install the 2 clips.
![]() |
for Temper Spare Tire:
Engage the 8 claws and install the rear deck trim cover.
Install the 2 clips.
| 12. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH |
![]() |
Engage the 8 clips, the retainer and the 10 claws and install the front quarter trim panel.
![]() |
Install the belt of the rear seat outer belt onto the rear seat shoulder belt hanger.
| 13. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH |
| 14. INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY RH (w/ Seat Belt Bar) |
![]() |
Install the front seat outer belt bar with the 2 bolts.
| 15. INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY LH (w/ Seat Belt Bar) |
| 16. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Install the front door opening trim weatherstrip.
| 17. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 18. INSTALL FRONT DOOR SCUFF PLATE RH |
![]() |
Engage the 8 claws and install the front door scuff plate.
| 19. INSTALL FRONT DOOR SCUFF PLATE LH |
| 20. INSTALL REAR SEAT ASSEMBLY RH |
![]() |
Insert the 2 location pins through the 2 body holes and install the rear seat.
Using "TORX" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.
![]() |
Install the rear seat cushion.
Using "TORX" socket wrench E10, install the 2 bolts in the sequence shown in the illustration.
| 21. INSTALL REAR SEAT ASSEMBLY LH |
![]() |
Insert the 2 location pins through the 2 body holes and install the rear seat.
Using "TORX" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.
![]() |
Install the rear seat cushion.
Using "TORX" socket wrench E10, install the 3 bolts in the sequence shown in the illustration.
| 22. INSTALL NO. 1 REAR SEAT LEG COVER |
for RH Side:
Install the No. 1 rear seat leg cover .
for LH Side:
Install the No. 1 rear seat leg cover .
| 23. INSTALL NO. 2 REAR SEAT LEG COVER |
![]() |
Engage the 3 claws and install the No. 2 rear seat leg cover.
| 24. INSTALL DECK FLOOR BOX RH (w/ Deck Board) |
![]() |
Set the deck floor box and lock the 2 knobs.
| 25. INSTALL DECK FLOOR BOX LH (w/ Deck Board) |
| 26. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board) |
![]() |
Install the spare wheel cover.
| 27. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board) |
![]() |
Set the deck board and lock the 2 knobs.
| 28. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board) |
![]() |
Install the rear floor carpet.
| 29. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim) |
![]() |
Engage the 2 claws and install the package tray trim panel.
Install the 5 pieces of hook tape.
Install the 2 package tray trim suspenders.
| 30. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Luggage Compartment Room Light) |