Home › STEERING › POWER STEERING › ELECTRONIC POWER STEERING SYSTEM

DTC    C1511/11    Torque Sensor 1 Malfunction

DTC    C1512/12    Torque Sensor Circuit Malfunction

DTC    C1513/13    Torque Sensor Circuit Malfunction

DTC    C1514/14    Torque Sensor Power Source Circuit Malfunction

DTC    C1517/17    Torque Sensor Hold Malfunction

for Preparation Click here


DESCRIPTION

The torque sensor converts the rotation torque input from the steering wheel into electric signals and sends them to the power steering ECU.

DTC No.
Detection Item
Trouble Area
C1511/11
Torque sensor (TRQ1) signal error or stop
  1. Torque sensor (built into steering column assembly)
  1. Power steering ECU
C1512/12
Torque sensor (TRQ2) signal error or stop
C1513/13
Deviation between torque sensor TRQ1 and TRQ2 exceeds specified value
C1514/14
Torque sensor power source voltage error
C1517/17
Temporary control due to malfunction related to torque sensor continues for long time

WIRING DIAGRAM


C162258E06


INSPECTION PROCEDURE

1.READ VALUE USING DATA LIST (TORQUE SENSOR OUTPUT)
  1. Connect the intelligent tester to DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / EMPS / Data List.

  1. Select the items Torque Sensor 1 Output and Torque Sensor 2 Output in the Data List and read the value displayed on the intelligent tester.

    EMPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Torque Sensor 1 Output
    Torque sensor 1 output value
    Minimum: 0 V, Maximum: 5 V
    2.3 to 2.7 V: Steering wheel not turned (without load)
    Read value with vehicle stopped
    2.5 to 4.7 V: Steering wheel turned to right
    0.3 to 2.5 V: Steering wheel turned to left
    Torque Sensor 2 Output
    Torque sensor 2 output value
    Minimum: 0 V, Maximum: 5 V
    2.3 to 2.7 V: Steering wheel not turned (without load)
    2.5 to 4.7 V: Steering wheel turned to right
    0.3 to 2.5 V: Steering wheel turned to left

  1. Check the difference in the values between Torque Sensor 1 Output and Torque Sensor 2 Output.

OK:
The voltage difference is below 0.3 V.



NG
Go to step 2
OK

CHECK INTERMITTENT PROBLEMS 

2.INSPECT POWER STEERING ECU (OUTPUT)
C162259E09
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    c1-6 (TRQV) - c1-8 (TRQG)
    Ignition switch ON
    7.5 to 8.5 V



NG
REPLACE POWER STEERING ECU
OK


3.INSPECT STEERING COLUMN ASSEMBLY (TORQUE SENSOR)
C162259E10
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    c1-5 (TRQ1) - c1-8 (TRQG)
    Ignition switch ON
    Steering wheel not turned (without load)
    2.3 to 2.7 V
    Ignition switch ON
    Steering wheel turned to right with vehicle stopped
    2.5 to 4.7 V
    Ignition switch ON
    Steering wheel turned to left with vehicle stopped
    0.3 to 2.5 V
    c1-7 (TRQ2) - c1-8 (TRQG)
    Ignition switch ON
    Steering wheel not turned (without load)
    2.3 to 2.7 V
    Ignition switch ON
    Steering wheel turned to right with vehicle stopped
    2.5 to 4.7 V
    Ignition switch ON
    Steering wheel turned to left with vehicle stopped
    0.3 to 2.5 V



NG
REPLACE STEERING COLUMN ASSEMBLY
OK

REPLACE POWER STEERING ECU