Home › STEERING › POWER STEERING › ELECTRONIC POWER STEERING SYSTEM

DTC    C1524/24    Motor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The power steering ECU supplies the current to the power steering motor through the motor circuit.

DTC No.
DTC Detection Condition
Trouble Area
C1524/24
Short (or open) in motor circuit or abnormal voltage or current in motor circuit.
  1. Steering column assembly
  2. Power steering ECU

WIRING DIAGRAM


C105153E06


INSPECTION PROCEDURE

1.READ VALUE USING DATA LIST (MOTOR ACTUAL CURRENT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / EMPS / Data List.

  1. Select the item Motor Actual Current and Command Value Current in the Data List and read the value displayed on the intelligent tester.

    Standard Current:

    Data List Item
    Steering Position
    (Left Turned)
    Steering Position
    (Center)
    Steering Position
    (Right Turned)
    Motor Actual Current
    10 A to 55 A
    -1 A to +1 A
    -55 A to -10 A
    Command Value Current
    55 A
    0 A
    -55 A

    HINT:
    The current changes when steering wheel is turned.



NG
Go to step 2
OK

CHECK INTERMITTENT PROBLEMS 

2.INSPECT POWER STEERING ECU
C162259E13
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage (for LHD):
    Tester Connection
    Switch Condition
    Specified Condition
    b1-1 (M1) - A19-2 (PGND)
    Ignition switch ON
    Steering wheel turned to right
    Below 1 V
    Ignition switch ON
    steering wheel turned to left
    11 to 14 V
    b1-2 (M2) - A19-2 (PGND)
    Ignition switch ON
    Steering wheel turned to right
    11 to 14 V
    Ignition switch ON
    steering wheel turned to left
    Below 1 V

    Standard Voltage (for RHD):
    Tester Connection
    Switch Condition
    Specified Condition
    b1-1 (M1) - A19-2 (PGND)
    Ignition switch ON
    Steering wheel turned to right
    11 to 14 V
    Ignition switch ON
    steering wheel turned to left
    Below 1 V
    b1-2 (M2) - A19-2 (PGND)
    Ignition switch ON
    Steering wheel turned to right
    Below 1 V
    Ignition switch ON
    steering wheel turned to left
    11 to 14 V

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 4
A


3.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BODY GROUND)
C162260E04
  1. Disconnect the connector from the power steering ECU.

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Condition
Specified Condition
A19-1 (PIG) - Body ground
Ignition switch ON
11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
A19-2 (PGND) - Body ground
Always
Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT STEERING COLUMN ASSEMBLY (POWER STEERING MOTOR)
C162261E04
  1. Disconnect the connector from the power steering ECU.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
b1-1 (M1) - b1-2 (M2)
Always
0.08 to 0.15 Ω
b1-1 (M1) - Body ground
Always
1 MΩ or higher
b1-2 (M2) - Body ground
Always
1 MΩ or higher



NG
REPLACE STEERING COLUMN ASSEMBLY
OK

REPLACE POWER STEERING ECU