Home › STEERING › POWER STEERING › ELECTRONIC POWER STEERING SYSTEM

ELECTRONIC POWER STEERING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Turn the ignition switch off.

  2. Connect an intelligent tester to the DLC3.

  3. Turn the ignition switch to ON.

  4. Turn the tester on.

  5. Enter the following menus: Chassis / EMPS / Data List.

  6. According to the display on the tester, read the Data List.


EMPS 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Torque Sensor 1 Output
Torque sensor 1 output value:
Minimum: 0 V, Maximum: 5 V
2.3 to 2.7 V: Steering wheel not turned (without load)
Read value with vehicle stopped
2.5 to 4.7 V: Steering wheel turned to right
Read value with vehicle stopped
0.3 to 2.5 V: Steering wheel turned to left
Read value with vehicle stopped
Torque Sensor 2 Output
Torque sensor 2 output value:
Minimum: 0 V, Maximum: 5 V
2.3 to 2.7 V: Steering wheel not turned (without load)
Read value with vehicle stopped
2.5 to 4.7 V: Steering wheel turned to right
Read value with vehicle stopped
0.3 to 2.5 V: Steering wheel turned to left
Read value with vehicle stopped
Torque Sensor 3 Output
Torque value for assist control:
Minimum: 0 V, Maximum: 5 V
2.3 to 2.7 V: Steering wheel not turned (without load)
Read value with vehicle stopped
2.5 to 4.7 V: Steering wheel turned to right
Read value with vehicle stopped
0.3 to 2.5 V: Steering wheel turned to left
Read value with vehicle stopped
Meter Vehicle Velocity
Vehicle speed from meter:
Minimum: 0 km/h (mph), Maximum: 255 km/h (158.5 mph)
0 km/h (mph): Vehicle stopped
-
Vehicle driven at constant speed
No significant fluctuation
Motor Actual Current
Current to motor:
Minimum: -128 A, Maximum: 127 A
Value changes in proportion to steering effort
-
Command Value Current
Requested current to motor:
Minimum: -128 A, Maximum: 127 A
Value changes in proportion to steering effort
-
Thermistor Temperature
ECU substrate temperature:
Minimum: -50 °C, Maximum: 205 °C
-
-
PIG Power Supply
Power source voltage to activate motor:
Minimum: 0 V, Maximum: 25.5 V
11 to 14 V: Always
-
IG Power Supply
ECU power source voltage:
Minimum: 0 V, Maximum: 25.5 V
11 to 14 V: Ignition switch ON
-
TRQ1 Zero Point Value
Zero point value of torque sensor 1:
Minimum: 0 V, Maximum: 5 V
2.3 to 2.7 V: Steering wheel not turned (without load)
-
TRQ2 Zero Point Value
Zero point value of torque sensor 2:
Minimum: 0 V, Maximum: 5 V
2.3 to 2.7 V: Steering wheel not turned (without load)
-
TRQ3 Zero Point Value
Zero point value of torque sensor for assist control:
Minimum: 0 V, Maximum: 5 V
2.3 to 2.7 V: Steering wheel not turned (without load)
-
Motor Terminal Volt (+)
Motor terminal M1 voltage:
Minimum: 0 V, Maximum: 25.5 V
Below 1 V: Steering wheel turned to right (LHD)
11 to 14 V: Steering wheel turned to right (RHD)
-
11 to 14 V: Steering wheel turned to left (LHD)
Below 1 V: Steering wheel turned to left (RHD)
-
Motor Terminal Volt (-)
Motor terminal M2 voltage:
Minimum: 0 V, Maximum: 25.5 V
11 to 14 V: Steering wheel turned to right (LHD)
Below 1 V: Steering wheel turned to right (RHD)
-
Below 1 V: Steering wheel turned to left (LHD)
11 to 14 V: Steering wheel turned to left (RHD)
-
Motor Overheat Record
Continuous overheat prevention control record:
Rec/Unrec
Unrec
-
Motor Low Power Record
PIG power source voltage drop record:
Rec/Unrec
Unrec
-
Battery Voltage Lo Record
Battery voltage reduction history
Minimum: 0 times, Maximum: 255 times
0 times
*
Control Mode
Codes indicating DTC detection timing during ECU control displayed in hexadecimal
-
-
IG ON/OFF Times
Number of times ignition switch turned ON after DTC detection:
Minimum: 0 time, Maximum: 255 times
-
-
Number of Trouble Code
Number of detected DTCs when freeze frame data stored:
Minimum: 0 time, Maximum: 255 times
-
-
ECU Identification
ECU identification information
-
-

HINT:
*: Inspect the charging system if the display for "Battery Voltage Lo Record" is other than "0".
  1. for 2NZ-FE engine (Click here).
  2. for 1NZ-FE engine (Click here).