Home › SUSPENSION & AXLE › SUSPENSION › FRONT LOWER SUSPENSION ARM (for 1NZ-FE RH Side, 2NZ-FE RH Side)

FRONT LOWER SUSPENSION ARM (for 1NZ-FE RH Side, 2NZ-FE RH Side) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE HOOD SUB-ASSEMBLY (for Hatchback)
  1. Remove the 4 bolts and remove the hood.



3. REMOVE HOOD SUB-ASSEMBLY (for Sedan)
  1. Remove the 4 bolts and remove the hood.



4. REMOVE FRONT WIPER ARM HEAD CAP (for Hatchback)


E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.



5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH (for Hatchback)
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113850
  1. Remove the nut and front wiper arm.



6. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH (for Hatchback)

HINT:
Use the same procedure as for the LH side.



7. REMOVE HOOD TO COWL TOP SEAL (for Hatchback)


E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.



8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Hatchback LHD)


E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.



    E113852
  1. Disconnect the washer hose.

  1. Disengage the 11 claws and clip.



    E113854
  1. Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.



9. REMOVE COWL TOP VENTILATOR LOUVER LH (for Hatchback LHD)


E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.



10. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Hatchback RHD)


E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.



11. REMOVE COWL TOP VENTILATOR LOUVER LH (for Hatchback RHD)


E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.



12. REMOVE FRONT WIPER MOTOR AND LINK (for Hatchback)


E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.



13. REMOVE NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY (for Hatchback)


A108437
  1. Disengage the claw and remove cowl to register duct sub-assembly No. 2.



14. REMOVE COWL TOP PANEL OUTER (for Hatchback)


A108438
  1. Disengage the wire harness clamp.



    A115392
  1. Remove the 9 bolts and remove the cowl top panel outer.



15. REMOVE FRONT WIPER ARM HEAD CAP (for Sedan)


    E127832E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.



16. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH (for Sedan)


    E127833
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. Remove the nut and front wiper arm.



17. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH (for Sedan)

HINT:
Use the same procedure as for the LH side.



18. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH (for Sedan)


    E127834E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.



19. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH (for Sedan)

HINT:
Use the same procedure as for the LH side.



20. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan LHD)


    E127838
  1. Disengage the 3 clips, the 4 claws and the 8 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.



    E127839
  1. Disconnect the washer hoses.

  1. Disengage the 5 hooks.



21. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan RHD)


    E127835
  1. Disengage the 2 clips, the 6 claws and the 10 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.



    E127836
  1. Disconnect the washer hoses.

  1. Disengage the 5 hooks.



22. REMOVE FRONT WIPER MOTOR AND LINK (for Sedan)


    E127837
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.



23. REMOVE FRONT AIR SHUTTER SEAL (for Sedan)


A133324
  1. Disengage the 3 claws and remove the front air shutter seal.



24. REMOVE COWL TOP PANEL OUTER (for Sedan)


A128446
  1. Disengage the wire harness clamp.



    A128447
  1. Remove the 2 bolts and remove the cowl top to cowl inner brace.



    A128448
  1. Remove the 8 bolts and remove the cowl top panel outer.



25. POSITION WHEELS FACING STRAIGHT AHEAD


26. REMOVE FRONT WHEEL


27. REMOVE COLUMN HOLE COVER SILENCER SHEET


    A116501E01
  1. Remove the floor carpet and 2 clips and remove the column hole cover silencer.



28. REMOVE STEERING SLIDING YOKE SUB-ASSEMBLY


    C117212
  1. Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.



    C118005E08
  1. Place matchmarks on the sliding yoke of the steering intermediate shaft assembly and the steering gear assembly.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *a
    Matchmark

  1. Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.



29. REMOVE STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    C139112E02
  1. Remove clip A, separate clip B from the body and separate No. 1 steering column hole cover.
    Text in Illustration 
    *1
    Clip A
    *2
    Clip B

    NOTICE:
    Do not damage clip B.



30. SEPARATE TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.



    C172757E01
  1. Install SST (spacer B) to the threaded section of the tie rod end.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure the upper ends of the threaded section of the tie rod end and SST (spacer B) are aligned.



  1. Using SST, separate the tie rod end from the front axle assembly.


    C172758E01

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    2. Install SST so that A and B are parallel.
    3. Be sure to place the wrench on the part indicated in the illustration.
    4. Do not damage the ball joint dust cover.
    5. Do not damage the front disc brake dust cover.



31. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.



32. SEPARATE FRONT SUSPENSION LOWER ARM LH


C107513
  1. Remove the clip and castle nut.



    C172759E01
  1. Install SST (spacer B) to the threaded section of the lower ball joint.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure the upper ends of the threaded section of the lower ball joint and SST (spacer B) are aligned.



  1. Using SST, separate the front lower suspension arm from the front axle assembly.


    C172760E01

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    2. Install SST so that A and B are parallel.
    3. Be sure to place the wrench on the part indicated in the illustration.
    4. Do not damage the lower ball joint dust cover.
    5. Do not damage the drive shaft outboard joint boots.
    6. Do not damage the front disc brake dust cover.



33. SEPARATE FRONT SUSPENSION LOWER ARM RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.



34. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH


C106044
  1. Remove the nut and separate the stabilizer link from the shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.



35. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.



36. SUSPEND ENGINE ASSEMBLY
  1. Remove the bolt and remove the radio setting condenser.

  1. Remove the bolt and remove the air-fuel ratio sensor wiring bracket.



    A070012E02
  1. Install the engine hanger with the bolt in the position shown in the illustration.
    Text in Illustration 
    *a
    Front
    *b
    Rear
    Part No. 
    Engine hanger
    12281-21010
    Bolt
    91642-81025

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Using an engine sling device and a chain block, support the engine assembly w/transaxle and front suspension crossmember.



37. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    C107979E01
  1. Remove the bolt and separate the engine moving control rod.

  1. Support the front suspension crossmember with a transmission jack.



    C107982
  1. Remove the 6 bolts and remove the suspension crossmember.



38. REMOVE FRONT SUSPENSION LOWER ARM RH


C112612
  1. Remove the bolt and lower arm.