Home › SUSPENSION & AXLE › SUSPENSION › FRONT STABILIZER BAR (for Sedan)

FRONT STABILIZER BAR (for Sedan) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE HOOD SUB-ASSEMBLY
  1. Remove the 4 bolts and remove the hood.



3. REMOVE FRONT WIPER ARM HEAD CAP


    E127832E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.



4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E127833
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. Remove the nut and front wiper arm.



5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



6. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E127834E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.



7. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


    E127838
  1. Disengage the 3 clips, the 4 claws and the 8 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.



    E127839
  1. Disconnect the washer hoses.

  1. Disengage the 5 hooks.



9. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


    E127835
  1. Disengage the 2 clips, the 6 claws and the 10 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.



    E127836
  1. Disconnect the washer hoses.

  1. Disengage the 5 hooks.



10. REMOVE FRONT WIPER MOTOR AND LINK


    E127837
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.



11. REMOVE FRONT AIR SHUTTER SEAL


A133324
  1. Disengage the 3 claws and remove the front air shutter seal.



12. REMOVE COWL TOP PANEL OUTER


A128446
  1. Disengage the wire harness clamp.



    A128447
  1. Remove the 2 bolts and remove the cowl top to cowl inner brace.



    A128448
  1. Remove the 8 bolts and remove the cowl top panel outer.



13. POSITION WHEELS FACING STRAIGHT AHEAD


14. REMOVE FRONT WHEEL


15. REMOVE COLUMN HOLE COVER SILENCER SHEET


    A116501E01
  1. Remove the floor carpet and 2 clips and remove the column hole cover silencer.



16. REMOVE STEERING SLIDING YOKE SUB-ASSEMBLY


    C139107
  1. Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.



    C118005E08
  1. Place matchmarks on the sliding yoke of the steering intermediate shaft assembly and the steering gear assembly.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *a
    Matchmark

  1. Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.



17. REMOVE STEERING COLUMN HOLE COVER SUB-ASSEMBLY


C139112E02
  1. Remove clip A, separate clip B from the body and separate No. 1 steering column hole cover.
    Text in Illustration 
    *1
    Clip A
    *2
    Clip B

    NOTICE:
    Do not damage clip B.



18. SEPARATE TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.



    C172757E01
  1. Install SST (spacer B) to the threaded section of the tie rod end.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure the upper ends of the threaded section of the tie rod end and SST (spacer B) are aligned.



  1. Using SST, separate the tie rod end from the front axle assembly.


    C172758E01

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    2. Install SST so that A and B are parallel.
    3. Be sure to place the wrench on the part indicated in the illustration.
    4. Do not damage the ball joint dust cover.
    5. Do not damage the front disc brake dust cover.



19. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.



20. SEPARATE FRONT SUSPENSION LOWER ARM LH


C107513
  1. Remove the clip and castle nut.



    C172759E01
  1. Install SST (spacer B) to the threaded section of the lower ball joint.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure the upper ends of the threaded section of the lower ball joint and SST (spacer B) are aligned.



  1. Using SST, separate the front lower suspension arm from the front axle assembly.


    C172760

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    2. Install SST so that A and B are parallel.
    3. Be sure to place the wrench on the part indicated in the illustration.
    4. Do not damage the lower ball joint dust cover.
    5. Do not damage the drive shaft outboard joint boots.
    6. Do not damage the front disc brake dust cover.



21. SEPARATE FRONT SUSPENSION LOWER ARM RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.



22. REMOVE FRONT STABILIZER LINK ASSEMBLY LH


C107518
  1. Remove the 2 nuts and stabilizer link

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.



23. REMOVE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.



24. SUSPEND ENGINE ASSEMBLY


  1. 1NZ-FE, 2NZ-FE

    1. Remove the bolt and remove the radio setting condenser.

    2. Remove the bolt and remove the air-fuel ratio sensor wiring bracket.



    3. A070012E02
    4. Install the engine hanger with the bolt in the position shown in the illustration.
      Text in Illustration 
      *a
      Front
      *b
      Rear
      Part No. 
      Engine hanger
      12281-21010
      Bolt
      91642-81025

      Torque:
      40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    5. Using an engine sling device and a chain block, support the engine assembly w/transaxle and front suspension crossmember.



25. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    C107979E01
  1. Remove the bolt and separate the engine moving control rod.

  1. Support the front suspension crossmember with a transmission jack.



    C107982
  1. Remove the 6 bolts and remove the suspension crossmember.



26. REMOVE POWER STEERING GEAR


C117189
  1. Remove the 2 bolts and 2 nuts and remove the steering gear assembly from the suspension crossmember.

    NOTICE:
    Keep the nut from rotating while turning the bolt.



27. REMOVE FRONT STABILIZER BRACKET LH


C116871
  1. Remove the 2 bolts and the stabilizer bracket.



28. REMOVE FRONT STABILIZER BRACKET RH
  1. Remove the 2 bolts and the stabilizer bracket.



29. REMOVE FRONT STABILIZER BAR


30. REMOVE FRONT STABILIZER BAR BUSH