Home › SUSPENSION & AXLE › SUSPENSION › REAR AXLE BEAM (for Hatchback)

REAR AXLE BEAM (for Hatchback) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE REAR WHEEL


3. DRAIN BRAKE FLUID

NOTICE:
Immediately wash off any brake fluid that comes into contact with any painted surfaces.



4. SEPARATE SKID CONTROL SENSOR WIRE (w/ ABS)


C125279
  1. Using a screwdriver, remove the claw of the connector lock portion and disconnect the skid control sensor wire connector.

    NOTICE:
    Do not remove the connector cover from the connector because the skid control sensor wire may be damaged.



    C107566
  1. Remove the nut and separate the skid control sensor wire.



5. SEPARATE REAR BRAKE NO. 4 TUBE


C107570E04
  1. Using SST, separate the brake tube from the flexible hose.

    SST
    09023-00100  

  1. Remove the clip and disconnect the flexible hose from the axle beam.

  1. Remove the nut and separate the brake tube.



6. SEPARATE REAR BRAKE NO. 3 TUBE

HINT:
The removal procedure for the RH side is the same as that for the LH side.



7. SEPARATE PARKING BRAKE NO. 3 CABLE ASSEMBLY


C126196
  1. Using pliers, pinch both ends of the claw of cable clamp and flex the clamp to remove it.

  1. Remove the bolt and separate the parking brake cable.



8. SEPARATE PARKING BRAKE NO. 2 CABLE ASSEMBLY

HINT:
The removal procedure for the RH side is the same as that for the LH side.



9. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY
  1. Release the parking brake and remove the rear brake drum.
    If the rear brake drum cannot be removed easily, perform the following procedure.



    F046068E02
  1. Remove the hole plug and insert a screwdriver through the hole into the backing plate, and hold the automatic adjust lever away from the adjuster.

  1. Using another screwdriver, contract the brake shoe by turning the adjusting bolt.



10. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH


C121821
  1. Remove the 4 bolts and remove the axle hub and bearing from the axle beam.

    NOTICE:
    Suspend the backing plate with a piece of rope.



11. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.



12. LOOSEN REAR AXLE BEAM


C112605E05
  1. Loosen the 2 bolts.

    NOTICE:
    Do not remove the bolts.



13. REMOVE REAR ABSORBER CAP


14. REMOVE REAR ABSORBER CAP


15. REMOVE REAR SHOCK ABSORBER CAP LH


16. REMOVE REAR SHOCK ABSORBER CAP RH


17. REMOVE REAR SHOCK ABSORBER LH
  1. Support the axle beam with a jack. Insert a wooden block between the jack and the rear axle spring seat to prevent damage.



    C106030
  1. Remove the 2 nuts while keeping the piston rod from rotating.

  1. Remove the cushion retainer and suspension support.



    C106031
  1. Remove the bolt while keeping the nut from rotating and remove the shock absorber.

    NOTICE:
    Remove the nut from the bolt side because the one on the lower side is a jam nut.



18. REMOVE REAR SHOCK ABSORBER RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.



19. REMOVE REAR COIL SPRING LH
  1. Lower the jacks slowly.

  1. Remove the coil spring, coil spring insulator upper and coil spring insulator lower.



20. REMOVE REAR COIL SPRING RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.



21. REMOVE REAR AXLE BEAM


C112605E05
  1. Remove the 2 bolts and remove the axle beam.