Home › TRANSMISSION ยท C54 MANUAL TRANSAXLE › MANUAL TRANSAXLE ASSEMBLY (for Hatchback)

MANUAL TRANSAXLE ASSEMBLY (for Hatchback) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE COLUMN HOLE COVER SILENCER SHEET


    A116501E01
  1. Remove the floor carpet and 2 clips and remove the column hole cover silencer.



3. REMOVE STEERING SLIDING YOKE SUB-ASSEMBLY


    C117212
  1. Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.



    C118005E08
  1. Place matchmarks on the sliding yoke of the steering intermediate shaft assembly and the steering gear assembly.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *a
    Matchmark

  1. Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.



4. REMOVE FRONT WHEELS


5. REMOVE ENGINE UNDER COVER LH


6. REMOVE ENGINE UNDER COVER RH


7. DRAIN TRANSAXLE OIL
  1. Remove the filler plug and the gasket.

  1. Remove the drain plug and gasket, and then drain the manual transaxle oil.

  1. Install a new gasket and the drain plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



8. REMOVE HOOD SUB-ASSEMBLY


9. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113850
  1. Remove the nut and front wiper arm.



10. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



11. REMOVE HOOD TO COWL TOP SEAL


E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.



12. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.



    E113852
  1. Disconnect the washer hose.

  1. Disengage the 11 claws and clip.



    E113854
  1. Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.



13. REMOVE COWL TOP VENTILATOR LOUVER LH (for LHD)


E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.



14. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.



15. REMOVE COWL TOP VENTILATOR LOUVER LH (for RHD)


E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.



16. REMOVE WINDSHIELD WIPER MOTOR AND LINK


E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.



17. REMOVE COWL TO REGISTER DUCT SUB-ASSEMBLY NO.2


A108437
  1. Disengage the claw and remove cowl to register duct sub-assembly No. 2.



18. REMOVE COWL TOP PANEL OUTER


A108438
  1. Disengage the wire harness clamp.



    A115392
  1. Remove the 9 bolts and remove the cowl top panel outer.



19. REMOVE CYLINDER HEAD COVER NO.2


A116235
  1. Remove the 4 nuts and cylinder head cover No. 2.



20. REMOVE AIR CLEANER ASSEMBLY


A117355
  1. Separate the intake air flow meter connector and wire harness clamp.

  1. Separate the fuel vapor feed hose and fuel vapor feed hose No. 1 from the vacuum switching valve assembly.

  1. Separate the vacuum switching valve connector and wire harness clamp.

  1. Separate the ventilation hose from the air cleaner hose.

  1. Release the air cleaner cap sub-assembly with air cleaner hose No. 1.

  1. Loosen the air cleaner hose clamp on the throttle body side and remove the air cleaner cap and air cleaner hose.

  1. Remove the air cleaner element.



    A104895
  1. Separate the wire harness clamp from the air cleaner case.

  1. Remove the 2 bolts and remove the air cleaner case with air cleaner inlet No. 1.



21. REMOVE AIR CLEANER BRACKET


C106369
  1. Remove the 2 bolts and the air cleaner bracket.



22. REMOVE BATTERY CLAMP SUB-ASSEMBLY


23. REMOVE BATTERY


24. REMOVE BATTERY TRAY


25. REMOVE BATTERY CARRIER


C106370
  1. Remove the 5 bolts and the battery carrier.



26. SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY


C106371
  1. Remove the 4 bolts, then separate the clutch release cylinder.

    HINT:
    Suspend the clutch release cylinder with a piece of rope so as not to overload the clutch pipe.



27. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY


C115305
  1. Remove the 2 clips and the 2 washers, and disconnect the 2 cables from the transaxle.

  1. Remove the 2 clips and disconnect the 2 cables from the control cable bracket.



28. REMOVE CONTROL CABLE BRACKET


C106374
  1. Remove the 2 bolts and the control cable bracket.



29. DISCONNECT WIRE HARNESS


C108079
  1. Remove the bolt, then disconnect the wire harness.



30. DISCONNECT CONNECTOR
  1. Disconnect the back-up light switch connector.



31. REMOVE STARTER ASSEMBLY


A104498
  1. Remove the terminal cap.

  1. Remove the nut and disconnect terminal 30.

  1. Disconnect the connector.

  1. Remove the 2 bolts and remove the starter assembly.



32. REMOVE FRONT AXLE SHAFT LH NUT


C085629E02
  1. Using SST and a hammer, release the staked part of the axle hub nut.

    SST
    09930-00010  

    NOTICE:
    1. Insert SST into the groove with the flat surface facing up.
    2. Do not damage the tip of SST using grinders.
    3. Completely unstake the staked part before removing the axle hub nut.
    4. Do not damage the threads of the drive shaft.

  1. Using a 30 mm socket wrench, remove the axle hub nut.



33. REMOVE FRONT AXLE SHAFT RH NUT

HINT:
The removal procedure for the RH side is the same as that for the LH side.



34. SEPARATE SPEED SENSOR FRONT LH (w/ ABS)


C125274
  1. Remove the bolt and separate the speed sensor and flexible hose.



    C112274
  1. Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Keep the speed sensor tip and installation portion free of foreign matter.
    2. Remove the speed sensor without turning it from its original installation angle.



35. SEPARATE SPEED SENSOR FRONT RH (w/ ABS)

HINT:
The separation procedure for the RH side is the same as that for the LH side.



36. SEPARATE FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 LH


C107513
  1. Remove the clip and castle nut.



    C172759E01
  1. Install SST (spacer B) to the threaded section of the lower ball joint.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure the upper ends of the threaded section of the lower ball joint and SST (spacer B) are aligned.



  1. Using SST, separate the front lower suspension arm from the front axle assembly.


    C172760E01

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    2. Install SST so that A and B are parallel.
    3. Be sure to place the wrench on the part indicated in the illustration.
    4. Do not damage the lower ball joint dust cover.
    5. Do not damage the drive shaft outboard joint boots.
    6. Do not damage the front disc brake dust cover.



37. SEPARATE FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.



38. SEPARATE TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.



    C172757E01
  1. Install SST (spacer B) to the threaded section of the tie rod end.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure the upper ends of the threaded section of the tie rod end and SST (spacer B) are aligned.



  1. Using SST, separate the tie rod end from the front axle assembly.


    C172758E01

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    2. Install SST so that A and B are parallel.
    3. Be sure to place the wrench on the part indicated in the illustration.
    4. Do not damage the ball joint dust cover.
    5. Do not damage the front disc brake dust cover.



39. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.



40. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH


C106044
  1. Remove the nut and separate the stabilizer link from the shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.



41. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.



42. SEPARATE FRONT AXLE ASSEMBLY LH
  1. Using a plastic hammer, tap the end of the drive shaft and disengage the fitting between the drive shaft and front axle.

    HINT:
    If it is difficult to disengage the fitting, tap the end of the drive shaft with a brass bar and hammer.

  1. Push the front axle out of the vehicle to remove the drive shaft from the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Do not damage the speed sensor rotor.
    4. Suspend the drive shaft with a piece of string or the equivalent.



43. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.



44. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


C107924
  1. Using SST, remove the drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.



45. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH


C116896
  1. Using a screwdriver and hammer, remove the drive shaft.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.



46. SUSPEND ENGINE ASSEMBLY


D030284E01
  1. Install the 2 hangers in the correct direction.

  1. Attach the engine chain hoist to the hangers.

    CAUTION:
    Do not attempt to hang the engine by hooking the chain to any other part.

    Parts No.:
    Engine Hanger: 12281-21010

    Bolt:
    91642-81025

    Torque:
    40 N*m{ 408 kgf*cm , 29 ft.*lbf }



47. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    C107979E01
  1. Remove the bolt and separate the engine moving control rod.

  1. Support the front suspension crossmember with a transmission jack.



    C107982
  1. Remove the 6 bolts and remove the suspension crossmember.



48. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING CONTROL BRACKET


C116856
  1. Remove the 4 bolts and the engine mounting control bracket.



49. SUPPORT MANUAL TRANSAXLE ASSEMBLY


50. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR


C106372
  1. Remove the bolt and nut, then separate the engine mounting insulator LH.

  1. Remove the 5 bolts and the engine mounting insulator LH.



51. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET


C121108
  1. Remove the 4 bolts and the engine mounting bracket LH.



52. REMOVE MANUAL TRANSAXLE ASSEMBLY


C063143
  1. Remove the 7 bolts and the manual transaxle.