MANUAL TRANSAXLE ASSEMBLY (for Sedan) > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE COLUMN HOLE COVER SILENCER SHEET |
![]() |
Remove the floor carpet and 2 clips and remove the column hole cover silencer.
| 3. REMOVE STEERING SLIDING YOKE SUB-ASSEMBLY |
![]() |
Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.
![]() |
Place matchmarks on the sliding yoke of the steering intermediate shaft assembly and the steering gear assembly.
| *1 | Bolt A |
| *2 | Bolt B |
| *a | Matchmark |
Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.
| 4. REMOVE FRONT WHEELS |
| 5. REMOVE ENGINE UNDER COVER LH |
| 6. REMOVE ENGINE UNDER COVER RH |
| 7. DRAIN TRANSAXLE OIL |
Remove the filler plug and the gasket.
Remove the drain plug and gasket, and then drain the manual transaxle oil.
Install a new gasket and the drain plug.
| 8. REMOVE HOOD SUB-ASSEMBLY |
| 9. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Remove the nut and front wiper arm.
| 10. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH |
| 11. REMOVE HOOD TO COWL TOP SEAL |
| 12. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.
| 13. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH |
| 14. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD) |
![]() |
Disengage the 2 clips, the 6 claws and the 10 hooks.
Remove the cowl top ventilator louver sub-assembly.
![]() |
Disconnect the washer hoses.
Disengage the 5 hooks.
| 15. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD) |
![]() |
Disengage the 3 clips, the 4 claws and the 8 hooks.
Remove the cowl top ventilator louver sub-assembly.
![]() |
Disconnect the washer hoses.
Disengage the 5 hooks.
| 16. REMOVE WINDSHIELD WIPER MOTOR AND LINK |
![]() |
Remove the 2 bolts.
Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.
| 17. REMOVE FRONT AIR SHUTTER SEAL |
![]() |
Disengage the 3 claws and remove the front air shutter seal.
| 18. REMOVE COWL TOP PANEL OUTER |
![]() |
Disengage the wire harness clamp.
![]() |
Remove the 2 bolts and remove the cowl top to cowl inner brace.
![]() |
Remove the 8 bolts and remove the cowl top panel outer.
| 19. REMOVE CYLINDER HEAD COVER NO.2 |
![]() |
Remove the 4 nuts and cylinder head cover No. 2.
| 20. REMOVE AIR CLEANER ASSEMBLY |
![]() |
Separate the intake air flow meter connector and wire harness clamp.
Separate the fuel vapor feed hose and fuel vapor feed hose No. 1 from the vacuum switching valve assembly.
Separate the vacuum switching valve connector and wire harness clamp.
Separate the ventilation hose from the air cleaner hose.
Release the air cleaner cap sub-assembly with air cleaner hose No. 1.
Loosen the air cleaner hose clamp on the throttle body side and remove the air cleaner cap and air cleaner hose.
Remove the air cleaner element.
![]() |
Separate the wire harness clamp from the air cleaner case.
Remove the 2 bolts and remove the air cleaner case with air cleaner inlet No. 1.
| 21. REMOVE AIR CLEANER BRACKET |
![]() |
Remove the 2 bolts and the air cleaner bracket.
| 22. REMOVE BATTERY CLAMP SUB-ASSEMBLY |
| 23. REMOVE BATTERY |
| 24. REMOVE BATTERY TRAY |
| 25. REMOVE BATTERY CARRIER |
![]() |
Remove the 5 bolts and the battery carrier.
| 26. SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY |
![]() |
Remove the 4 bolts, then separate the clutch release cylinder.
| 27. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Remove the 2 clips and the 2 washers, and disconnect the 2 cables from the transaxle.
Remove the 2 clips and disconnect the 2 cables from the control cable bracket.
| 28. REMOVE CONTROL CABLE BRACKET |
![]() |
Remove the 2 bolts and the control cable bracket.
| 29. DISCONNECT WIRE HARNESS |
![]() |
Remove the bolt, then disconnect the wire harness.
| 30. DISCONNECT CONNECTOR |
Disconnect the back-up light switch connector.
| 31. REMOVE STARTER ASSEMBLY |
![]() |
Remove the terminal cap.
Remove the nut and disconnect terminal 30.
Disconnect the connector.
Remove the 2 bolts and remove the starter assembly.
| 32. REMOVE FRONT AXLE SHAFT LH NUT |
![]() |
Using SST and a hammer, release the staked part of the axle hub nut.
Using a 30 mm socket wrench, remove the axle hub nut.
| 33. REMOVE FRONT AXLE SHAFT RH NUT |
| 34. SEPARATE SPEED SENSOR FRONT LH (w/ ABS) |
![]() |
Remove the bolt and separate the speed sensor and flexible hose.
![]() |
Remove the bolt and separate the speed sensor from the steering knuckle.
| 35. SEPARATE SPEED SENSOR FRONT RH (w/ ABS) |
| 36. SEPARATE FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 LH |
![]() |
Remove the clip and castle nut.
![]() |
Install SST (spacer B) to the threaded section of the lower ball joint.
Using SST, separate the front lower suspension arm from the front axle assembly.

| 37. SEPARATE FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 RH |
| 38. SEPARATE TIE ROD END SUB-ASSEMBLY LH |
Remove the cotter pin and castle nut.
![]() |
Install SST (spacer B) to the threaded section of the tie rod end.
Using SST, separate the tie rod end from the front axle assembly.

| 39. SEPARATE TIE ROD END SUB-ASSEMBLY RH |
| 40. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH |
![]() |
Remove the nut and separate the stabilizer link from the shock absorber.
| 41. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH |
| 42. SEPARATE FRONT AXLE ASSEMBLY LH |
Using a plastic hammer, tap the end of the drive shaft and disengage the fitting between the drive shaft and front axle.
Push the front axle out of the vehicle to remove the drive shaft from the front axle.
| 43. SEPARATE FRONT AXLE ASSEMBLY RH |
| 44. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH |
![]() |
Using SST, remove the drive shaft.
| 45. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH |
![]() |
Using a screwdriver and hammer, remove the drive shaft.
| 46. SUSPEND ENGINE ASSEMBLY |
![]() |
Install the 2 hangers in the correct direction.
Attach the engine chain hoist to the hangers.
| 47. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
![]() |
Remove the bolt and separate the engine moving control rod.
Support the front suspension crossmember with a transmission jack.
![]() |
Remove the 6 bolts and remove the suspension crossmember.
| 48. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING CONTROL BRACKET |
![]() |
Remove the 4 bolts and the engine mounting control bracket.
| 49. SUPPORT MANUAL TRANSAXLE ASSEMBLY |
| 50. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR |
![]() |
Remove the bolt and nut, then separate the engine mounting insulator LH.
Remove the 5 bolts and the engine mounting insulator LH.
| 51. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET |
![]() |
Remove the 4 bolts and the engine mounting bracket LH.
| 52. REMOVE MANUAL TRANSAXLE ASSEMBLY |
![]() |
Remove the 7 bolts and the manual transaxle.