Home › SUSPENSION & AXLE › SUSPENSION › REAR WHEEL ALIGNMENT (for Hatchback)

REAR WHEEL ALIGNMENT (for Hatchback) > INSPECTION

for Preparation Click here



1. INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold tire inflation pressure:

    Vehicle Model
    Tire Size
    Vehicle Speed
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    NCP91R-AGMRKQ
    NCP91R-AHMRKQ
    NCP91R-AGPRKQ
    NCP91R-AHPRKQ
    NCP90R-AGMRKQ
    NCP90R-AHMRKQ
    NCP90R-AGPRKQ
    NCP90R-AHPRKQ
    175/65R14 82T
    185/60R15 84H
    Driving below 140 km/h (87 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 140 km/h (87 mph)
    260 (2.7, 38)
    260 (2.7, 38)
    NCP91L-AHMRK
    NCP91L-AGMRK
    NCP91L-AGPRK
    NCP91L-AHPRK
    NCP90L-AHMRK
    NCP90L-AGMRK
    NCP90R-AHMRK
    NCP90L-AGPRK
    NCP90L-AHPRK
    NCP90R-AHPRK
    175/65R14 82T
    185/60R15 84H
    Driving below 160 km/h (100 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 160 km/h (100 mph)
    230 (2.3, 33)
    230 (2.3, 33)
    NCP91L-AHPRKV
    NCP90L-AHMRKV
    NCP90L-AHPRKV
    175/65R14 82T
    185/60R15 84H
    Driving below 160 km/h (100 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 160 km/h (100 mph)
    230 (2.3, 33)
    230 (2.3, 33)



    R003031E01
  1. Using a dial indicator, check the tire runout.

    Tire runout:
    1.4 mm (0.055 in.) or less



2. MEASURE VEHICLE HEIGHT


C106034E01

Vehicle height:
Vehicle Model / Destination
A-B
C-D
NCP91R-AGMRKQ
NCP91R-AHMRKQ
NCP91R-AGPRKQ
NCP91R-AHPRKQ
NCP90R-AGMRKQ
NCP90R-AHMRKQ
NCP90R-AGPRKQ
NCP90R-AHPRKQ
88 mm
(3.46 in.)
12 mm
(0.47 in.)
NCP91L-AHMRK
NCP91L-AGMRK
NCP91L-AGPRK
NCP91L-AHPRK
NCP90L-AHMRK
NCP90L-AGMRK
NCP90R-AHMRK
NCP90L-AGPRK
NCP90L-AHPRK
NCP90R-AHPRK
NCP91L-AHPRKV
NCP90L-AHMRKV
NCP90L-AHPRKV
86 mm
(3.39 in.)
18 mm
(0.71 in.)
Rough Road Package
66 mm
(2.60 in.)
-2.0 mm
(-0.08 in.)

Measuring points:
A:
Ground clearance of front wheel center
B:
Ground clearance of lower arm set front bolt center
C:
Ground clearance of rear wheel center
D:
Ground clearance of axle beam set bolt center

NOTICE:
Before inspecting the wheel alignment, check the vehicle height.

HINT:
Bounce the vehicle up and down at the corners to stabilize the suspension before inspecting the vehicle height.



3. INSPECT CAMBER
  1. Install the camber-caster-kingpin gauge and position the rear wheel on the alignment tester.

  1. Inspect the camber.

    Camber:
    Vehicle Model / Destination
    Camber
    NCP91R-AGMRKQ
    NCP91R-AHMRKQ
    NCP91R-AGPRKQ
    NCP91R-AHPRKQ
    NCP90R-AGMRKQ
    NCP90R-AHMRKQ
    NCP90R-AGPRKQ
    NCP90R-AHPRKQ
    -0°56' +/- 45'
    (-0.93° +/- 0.75°)
    NCP91L-AHMRK
    NCP91L-AGMRK
    NCP91L-AGPRK
    NCP91L-AHPRK
    NCP90L-AHMRK
    NCP90L-AGMRK
    NCP90R-AHMRK
    NCP90L-AGPRK
    NCP90L-AHPRK
    NCP90R-AHPRK
    NCP91L-AHPRKV
    NCP90L-AHMRKV
    NCP90L-AHPRKV
    -0°56' +/- 45'
    (-0.93° +/- 0.75°)
    Rough Road Package
    -0°54' +/- 45'
    (-0.90° +/- 0.75°)

    NOTICE:
    The tolerance for the difference between the left and right wheels is 30' (0.5°) or less for both cambers.

    If the camber is not within the specified range, inspect the suspension parts and replace them if necessary.



4. INSPECT TOE-IN


SA03213E02

Toe-in:

Vehicle Model / Destination
Tire Size
A+B
C-D
NCP91R-AGMRKQ
NCP91R-AHMRKQ
NCP91R-AGPRKQ
NCP91R-AHPRKQ
NCP90R-AGMRKQ
NCP90R-AHMRKQ
NCP90R-AGPRKQ
NCP90R-AHPRKQ
175/65R14
0°15' +/- 0°20'
(0.25° +/- 0.33°)
2.6 +/- 3.0 mm
(0.10 +/- 0.12 in.)
185/60R15
0°15' +/- 0°20'
(0.25° +/- 0.33°)
2.7 +/- 3.0 mm
(0.11 +/- 0.12 in.)
NCP91L-AHMRK
NCP91L-AGMRK
NCP91L-AGPRK
NCP91L-AHPRK
NCP90L-AHMRK
NCP90L-AGMRK
NCP90R-AHMRK
NCP90L-AGPRK
NCP90L-AHPRK
NCP90R-AHPRK
NCP91L-AHPRKV
NCP90L-AHMRKV
NCP90L-AHPRKV
165/70R14
185/60R 15
0°17' +/- 0°20'
(0.28° +/- 0.33°)
2.9 +/- 3.0 mm
(0.11 +/- 0.12 in.)
175/65R14
0°17' +/- 0°20'
(0.28° +/- 0.33°)
2.8 +/- 3.0 mm
(0.11 +/- 0.12 in.)
Rough Road Package
175/65R14
185/60R15
0°13' +/- 0°20'
(0.22° +/- 0.33°)
2.2 +/- 3.0 mm
(0.09 +/- 0.12 in.)

HINT:
Only measure C-D when A+B cannot be measured