Home › SUSPENSION & AXLE › SUSPENSION › REAR WHEEL ALIGNMENT (for Sedan)

REAR WHEEL ALIGNMENT (for Sedan) > INSPECTION

for Preparation Click here



1. INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold tire inflation pressure:

    Vehicle Model
    Tire Size
    Vehicle Speed
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    NCP93R-BEMRKQ
    NCP93R-BEPRKQ
    175/65R14 82T
    185/60R15 84H
    Driving below 140 km/h (87 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 140 km/h (87 mph)
    260 (2.7, 38)
    260 (2.7, 38)
    NCP93L-BEMRK
    NCP93L-BEPRK
    NCP92L-BEMRK
    NCP92R-BEMRK
    NCP92L-BEPRK
    NCP92R-BEPRK
    175/65R14 82T
    185/60R15 84H
    Driving below 160 km/h (100 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 160 km/h (100 mph)
    230 (2.3, 33)
    230 (2.3, 33)
    NCP93L-BEMRKV
    NCP93L-BEPRKV
    NCP92L-BEMRKV
    NCP92L-BEPRKV
    175/65R14 82T
    185/60R15 84H
    Driving below 160 km/h (100 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 160 km/h (100 mph)
    230 (2.3, 33)
    230 (2.3, 33)



    R003031E01
  1. Using a dial indicator, check the tire runout.

    Tire runout:
    1.4 mm (0.055 in.) or less



2. MEASURE VEHICLE HEIGHT


C132096E01

Vehicle height:
Vehicle Model / Destination
A-B
C-D
NCP93R-BEMRKQ
NCP93R-BEPRKQ
86 mm
(3.39 in.)
9.0 mm
(0.35 in.)
NCP93L-BEMRK
NCP93L-BEPRK
NCP93L-BEPRK
NCP92L-BEMRK
NCP92R-BEMRK
NCP92L-BEPRK
NCP92R-BEPRK
NCP93L-BEMRKV
NCP93L-BEPRKV
NCP92L-BEMRKV
NCP92L-BEPRKV
86 mm
(3.39 in.)
14 mm
(0.55 in.)
Rough Road Package
66 mm
(2.60 in.)
-4.0 mm
(-0.16 in.)

Measuring points:
A:
Ground clearance of front wheel center
B:
Ground clearance of lower arm set front bolt center
C:
Ground clearance of rear wheel center
D:
Ground clearance of axle beam set bolt center

NOTICE:
Before inspecting the wheel alignment, check the vehicle height.

HINT:
Bounce the vehicle up and down at the corners to stabilize the suspension before inspecting the vehicle height.



3. INSPECT CAMBER
  1. Install the camber-caster-kingpin gauge and position the rear wheel on the alignment tester.

  1. Inspect the camber.

    Camber:
    Vehicle Model / Destination
    Camber
    NCP93R-BEMRKQ
    NCP93R-BEPRKQ
    -0°55' +/- 45'
    (-0.92° +/- 0.75°)
    NCP93L-BEMRK
    NCP93L-BEPRK
    NCP93L-BEPRK
    NCP92L-BEMRK
    NCP92R-BEMRK
    NCP92L-BEPRK
    NCP92R-BEPRK
    NCP93L-BEMRKV
    NCP93L-BEPRKV
    NCP92L-BEMRKV
    NCP92L-BEPRKV
    -0°56' +/- 45'
    (-0.93° +/- 0.75°)
    Rough Road Package
    -0°54' +/- 45'
    (-0.90° +/- 0.75°)

    NOTICE:
    The tolerance for the difference between the left and right wheels is 30' (0.5°) or less for both cambers.

    If the camber is not within the specified range, inspect the suspension parts and replace them if necessary.



4. INSPECT TOE-IN


SA03213E02

Toe-in:

Vehicle Model / Destination
Tire Size
A+B
C-D
NCP93R-BEMRKQ
NCP93R-BEPRKQ
175/65R14
0°15' +/- 0°20'
(0.25° +/- 0.33°)
2.5 +/- 3.0 mm
(0.10 +/- 0.12 in.)
185/60R15
0°15' +/- 0°20'
(0.25° +/- 0.33°)
2.6 +/- 3.0 mm
(0.10 +/- 0.12 in.)
NCP93L-BEMRK
NCP93L-BEPRK
NCP93L-BEPRK
NCP92L-BEMRK
NCP92R-BEMRK
NCP92L-BEPRK
NCP92R-BEPRK
NCP93L-BEMRKV
NCP93L-BEPRKV
NCP92L-BEMRKV
NCP92L-BEPRKV
175/65R14
0°16' +/- 0°20'
(0.27° +/- 0.33°)
2.7 +/- 3.0 mm
(0.11 +/- 0.12 in.)
185/60R15
0°16' +/- 0°20'
(0.27° +/- 0.33°)
2.8 +/- 3.0 mm
(0.11 +/- 0.12 in.)
Rough Road Package
175/65R14
0°12' +/- 0°20'
(0.20° +/- 0.33°)
2.0 +/- 3.0 mm
(0.08 +/- 0.12 in.)
185/60R15
0°12' +/- 0°20'
(0.20° +/- 0.33°)
2.1 +/- 3.0 mm
(0.08 +/- 0.12 in.)

HINT:
Only measure C-D when A+B cannot be measured.