DTC B1630/23 Driver Side Rear Airbag Sensor Circuit Malfunction |
| DTC No. | DTC Detecting Condition | Trouble Area |
| B1630/23 |
|
|

| 1.CHECK DTC |
![]() |
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the driver side rear airbag sensor.
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE (FOR OPEN) |
![]() |
Disconnect the connectors from the driver side - side airbag sensor and the driver side rear airbag sensor.
LHD:
Using a service wire, connect J15-2 (BCL+) and J15-1 (BCL-) of connector C.
RHD:
Using a service wire, connect J14-2 (BCR+) and J14-1 (BCR-) of connector C.
Measure the resistance.
| Tester connection | Condition | Specified condition |
| J17-1 (BCL+) - J17-2 (BCL-) (*1) | Always | Below 1 Ω |
| J16-1 (BCR+) - J16-2 (BCR+) (*2) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE (FOR SHORT) |
![]() |
Disconnect the service wire from connector C.
Measure the resistance.
| Tester connection | Condition | Specified condition |
| J17-1 (BCL+) - J17-2 (BCL-) (*1) | Always | 1 MΩ or higher |
| J16-1 (BCR+) - J16-2 (BCR-) (*2) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK FLOOR WIRE (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage.
| Tester connection | Condition | Specified condition |
| J17-1 (BCL+) - Body ground (*1) | Ignition switch ON | Below 1 V |
| J17-2 (BCL-) - Body ground (*1) | Ignition switch ON | Below 1 V |
| J16-1 (BCR+) - Body ground (*2) | Ignition switch ON | Below 1 V |
| J16-2 (BCR-) - Body ground (*2) | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 6.CHECK FLOOR WIRE (TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester connection | Condition | Specified condition |
| J17-1 (BCL+) - Body ground (*1) | Always | 1 MΩ or higher |
| J17-2 (BCL-) - Body ground (*1) | Always | 1 MΩ or higher |
| J16-1 (BCR+) - Body ground (*2) | Always | 1 MΩ or higher |
| J16-2 (BCR-) - Body ground (*2) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 7.CHECK DRIVER SIDE REAR AIRBAG SENSOR |
![]() |
Connect the connectors to the center airbag sensor assembly.
Interchange the driver side rear airbag sensor with the front passenger side rear airbag sensor and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check the DTCs (Click here).
| Result | Proceed to |
| DTC B1630/23 is output. | A |
| DTC B1635/24 is output. | B |
| DTC B1630/23 and B1635/24 are not output. | C |
|
| ||||
|
| ||||
| C | ||
| ||
| 8.CHECK DRIVER SIDE - SIDE AIRBAG SENSOR |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the driver side rear airbag sensor and front passenger side rear airbag sensor to their original positions and connect the connectors to them.
Interchange the driver side - side airbag sensor with the front passenger side - side airbag sensor and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1630/23 is output. | A |
| DTC B1635/24 is output. | B |
| Neither DTC B1630/23 nor B1635/24 is output. | C |
|
| ||||
|
| ||||
| C | ||
| ||