Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1635/24    Front Passenger Side Rear Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The front passenger side rear airbag sensor consists of parts including the diagnostic circuit and the lateral deceleration sensor.
When the center airbag sensor assembly receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1635/24 is recorded when a malfunction is detected in the front passenger side rear airbag sensor circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B1635/24
  1. Center airbag sensor assembly detects line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in front passenger side rear airbag sensor circuit for 2 seconds.
  2. Front passenger side rear airbag sensor malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Rear airbag sensor RH (Front passenger side rear airbag sensor) (LHD)
  3. Rear airbag sensor LH (Front passenger side rear airbag sensor) (RHD)
  4. Center airbag sensor assembly

WIRING DIAGRAM


H100108E03


INSPECTION PROCEDURE

1.CHECK DTC
H100851E02
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1635/24 is not output.

    HINT:
    DTCs other than DTC B1635/24 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front passenger side rear airbag sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


3.CHECK FLOOR WIRE (FOR OPEN)
H100165E02
  1. Disconnect the connectors from the front passenger side - side airbag censor and the front passenger side rear airbag sensor.

  1. LHD:
    Using a service wire, connect J14-2 (BCR+) and J14-1 (BCR-) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. RHD:
    Using a service wire, connect J15-2 (BCL+) and J15-1 (BCL-) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard Resistance:
    Tester connection
    Condition
    Specified condition
    J16-1 (BCR+) - J16-2 (BCR-) (*1)
    Always
    Below 1 Ω
    J17-1 (BCL+) - J17-2 (BCL-) (*2)
    Always
    Below 1 Ω

    *1: LHD
    *2: RHD



NG
REPAIR OR REPLACE FLOOR WIRE
OK


4.CHECK FLOOR WIRE (FOR SHORT)
H100153E02
  1. Disconnect the service wire from connector C.

  1. Measure the resistance.

    Standard Resistance:
    Tester connection
    Condition
    Specified condition
    J16-1 (BCR+) - J16-2 (BCR-) (*1)
    Always
    1 MΩ or higher
    J17-1 (BCL+) - J17-2 (BCL-) (*2)
    Always
    1 MΩ or higher

    *1: LHD
    *2: RHD



NG
REPAIR OR REPLACE FLOOR WIRE
OK


5.CHECK FLOOR WIRE (TO B+)
H100153E02
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage.

    Standard Voltage:
    Tester connection
    Condition
    Specified condition
    J16-1 (BCR+) - Body ground (*1)
    Ignition switch ON
    Below 1 V
    J16-2 (BCR-) - Body ground (*1)
    Ignition switch ON
    Below 1 V
    J17-1 (BCL+) - Body ground (*2)
    Ignition switch ON
    Below 1 V
    J17-2 (BCL-) - Body ground (*2)
    Ignition switch ON
    Below 1 V

    *1: LHD
    *2: RHD



NG
REPAIR OR REPLACE FLOOR WIRE
OK


6.CHECK FLOOR WIRE (TO GROUND)
H100153E02
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard Resistance:
    Tester connection
    Condition
    Specified condition
    J16-1 (BCR+) - Body ground (*1)
    Always
    1 MΩ or higher
    J16-2 (BCR-) - Body ground (*1)
    Always
    1 MΩ or higher
    J17-1 (BCL+) - Body ground (*2)
    Always
    1 MΩ or higher
    J17-2 (BCL-) - Body ground (*2)
    Always
    1 MΩ or higher

    *1: LHD
    *2: RHD



NG
REPAIR OR REPLACE FLOOR WIRE
OK


7.CHECK FRONT PASSENGER SIDE REAR AIRBAG SENSOR
H100852E08
  1. Connect the connectors to the center airbag sensor assembly.

  1. Interchange the front passenger side rear airbag sensor with driver side rear airbag sensor and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1635/24 is output.
    A
    DTC B1630/23 is output.
    B
    DTC B1630/23 and B1635/24 are not output.
    C



A
Go to step 8

B
REPLACE FRONT PASSENGER SIDE REAR AIRBAG SENSOR
C

USE SIMULATION METHOD TO CHECK 

8.CHECK FRONT PASSENGER SIDE - SIDE AIRBAG SENSOR
H100852E09
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the front passenger side rear airbag sensor and driver side rear airbag sensor to their original positions and connect the connectors to them.

  1. Interchange the front passenger side - side airbag sensor with the driver side - side airbag sensor and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1635/24 is output.
    A
    DTC B1630/23 is output.
    B
    Neither DTC B1630/23 nor B1635/24 is output.
    C



A
REPLACE CENTER AIRBAG SENSOR ASSEMBLY

B
REPLACE FRONT PASSENGER SIDE - SIDE AIRBAG SENSOR
C

USE SIMULATION METHOD TO CHECK