Home › BRAKE › BRAKE CONTROL › BRAKE ACTUATOR (for Sedan)

BRAKE ACTUATOR (for Sedan) > REMOVAL

for Preparation Click here



1. DRAIN BRAKE FLUID

NOTICE:
Immediately wash off any brake fluid that comes into contact with any painted surfaces.



2. REMOVE BATTERY


3. REMOVE BATTERY TRAY


4. REMOVE BATTERY CARRIER


5. REMOVE BRAKE ACTUATOR (for LHD)


C191621
  1. Remove the clip and disconnect the wire harness.

  1. Move the lock lever in the direction indicated by the arrow to release the lock and disconnect the brake actuator connector from the actuator.



    C116914
  1. Using a union nut wrench (10 mm), separate the brake tube from the front flexible hose.



    C116915
  1. Using a union nut wrench (10 mm), separate the 2 brake tubes from the brake tube No. 1 way.



    C121690
  1. Using a union nut wrench (10 mm), separate the 2 brake tubes from the brake master cylinder.



    C191622
  1. Using a union nut wrench (10 mm), separate the 6 brake tubes from the brake actuator.



    C191623E02
  1. Use tags or labels to identify the place to reconnect each brake tube.
    Text in Illustration 
    *1
    To Front Wheel RH
    *2
    To Front Wheel LH
    *3
    To Rear Wheel RH
    *4
    To Rear Wheel LH
    *5
    From Master Cylinder
    *6
    From Master Cylinder



    C116918
  1. Disconnect the brake tube clamp.



    C116921
  1. Remove the 3 bolts and the actuator with bracket.



6. REMOVE BRAKE ACTUATOR ASSEMBLY (for RHD with VSC)


C169917
  1. Release the lock lever and disconnect the brake actuator connector.

    NOTICE:
    Be careful not to allow brake fluid to enter the removed connector.



    C204312
  1. Using a union nut wrench (10 mm), separate the 6 brake tubes from the brake actuator.



    C204313E01
  1. Use tags or labels to identify the place to reconnect each brake tube.
    Text in Illustration 
    *1
    To Front Wheel RH
    *2
    To Front Wheel LH
    *3
    To Rear Wheel RH
    *4
    To Rear Wheel LH
    *5
    From Master Cylinder
    *6
    From Master Cylinder



    C169919
  1. Remove the 3 bolts and brake actuator with bracket.

    NOTICE:
    Do not damage the brake tubes or wire harness.



7. REMOVE BRAKE ACTUATOR (for RHD without VSC)


C107529
  1. Move the lock lever in the direction indicated by the arrow to release the lock and disconnect the brake actuator connector from the actuator.



    C107530
  1. Using a union nut wrench (10 mm), separate the 6 brake tubes from the brake actuator.



    C116919E02
  1. Use tags or labels to identify the place to reconnect each brake tube.
    Text in Illustration 
    *1
    To Front Wheel RH
    *2
    To Front Wheel LH
    *3
    To Rear Wheel RH
    *4
    To Rear Wheel LH
    *5
    From Master Cylinder
    *6
    From Master Cylinder



    C107531
  1. Remove the 3 bolts and the actuator with bracket.



8. REMOVE BRAKE ACTUATOR BRACKET ASSEMBLY (for LHD)


C215138
  1. Remove the 2 nuts and the actuator bracket.



9. REMOVE BRAKE ACTUATOR BRACKET ASSEMBLY (for RHD with VSC)


C169920
  1. Remove the 4 bolts and the actuator bracket.



10. REMOVE BRAKE ACTUATOR BRACKET ASSEMBLY (for RHD without VSC)


C215139
  1. Remove the 2 nuts and the actuator bracket.