FRONT DOOR (for Sedan) > DISASSEMBLY |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window) |
![]() |
Insert a clip remover between the plate and door trim.
Turn the handle with the clip remover inserted, as shown in the illustration.
Remove the front door window regulator handle and clip.
Remove the window regulator handle plate.
| 3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH |
![]() |
Disengage the claw and clip and remove the front door lower frame bracket garnish.
| 4. REMOVE FRONT ARMREST BASE UPPER PANEL |
![]() |
for Driver side with power window:
Remove the screw.
Disengage the 7 claws and 2 clips and remove the front armrest base upper panel.
Disconnect the connector.
![]() |
for Front passenger side with power window:
Remove the screw.
Disengage the 7 claws and 2 clips and remove the front armrest base upper panel.
Disconnect the connector.
![]() |
w/o Power window:
Remove the screw.
Disengage the 5 claws and 2 clips and remove the front armrest base upper panel.
| 5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/ Power Window) |
![]() |
Remove the 3 screws and the power window regulator master switch.
| 6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (w/ Power Window) |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the power window regulator switch.
| 7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
w/ Power window:
Remove the screw.
![]() |
Disengage the 9 clips.
![]() |
Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door trim board.
![]() |
w/o Power window:
Remove the screw.
![]() |
Disengage the 9 clips.
![]() |
Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door trim board.
| 8. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the front door inside handle.
| 9. REMOVE FRONT DOOR GLASS WEATHERSTRIP INNER |
Remove the front door glass weatherstrip inner from the front door trim board.
| 10. REMOVE FRONT NO.1 SPEAKER ASSEMBLY |
![]() |
Disconnect the speaker connector.
![]() |
Drill out the 3 rivet heads using a drill with a bit diameter of less than 4 mm (0.16 in.), and remove the front No.1 speaker.
Operate the drill around the rivet head circumference and cut out the flange.
After drilling out the flange, continue drilling to push out the shards on the drill.
Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.
| 11. REMOVE OUTER REAR VIEW MIRROR |
![]() |
w/ Power mirror:
Disconnect the connector.
Remove the 3 nuts, disengage the claw and remove the outer rear view mirror.
| 12. REMOVE FRONT DOOR BELT MOULDING |
![]() |
Apply protective tape to the door panel in the periphery of the front door belt moulding.
![]() |
Using a moulding remover, disengage the 6 claws and remove the front door belt moulding.
| 13. REMOVE FRONT DOOR TRIM BRACKET |
![]() |
Remove the 2 screws and front door trim bracket.
| 14. REMOVE FRONT DOOR SERVICE HOLE COVER |
![]() |
Disconnect the connectors and clamps, then remove the front door service hole cover.
| 15. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY |
w/ Power window:
Driver side:
Provisionally install the power window regulator master switch.
Passenger side:
Provisionally install the power window regulator switch.
w/o Power window:
Provisionally install the front door window regulator handle.
![]() |
Move the front door glass until the 2 bolts can be seen through the service holes.
Remove the 2 bolts.
![]() |
Remove the front door glass in the direction indicated by the arrows in the illustration.
w/ Power window:
Driver side:
Remove the power window regulator master switch.
Passenger side:
Remove the power window regulator switch.
w/o Power window:
Remove the front door window regulator handle.
| 16. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY |
![]() |
w/ Power window:
Disconnect the connector.
Loosen bolt A.
Remove the 5 bolts, then remove the front door window regulator.
![]() |
w/o Power window:
Loosen bolt A.
Remove the 5 bolts, then remove the front door window regulator.
| 17. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY FRONT (w/ Power Window) |
![]() |
Using "TORX" socket wrench T25, remove the 3 screws and power window regulator motor.
| 18. REMOVE FRONT DOOR GLASS RUN |
![]() |
Disengage the clip, then remove the front door glass run.
| 19. REMOVE FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER |
![]() |
Remove the bolt, then remove the front door frame sub-assembly rear lower.
| 20. REMOVE FRONT DOOR FRAME SUB-ASSEMBLY FRONT LOWER |
![]() |
Remove the bolt, then remove the front door frame sub-assembly front lower.
| 21. REMOVE FRONT DOOR OUTSIDE HANDLE COVER |
![]() |
Remove the hole plug.
Using "TORX" socket wrench T30, loosen the screw and remove the cover with the door lock key cylinder installed.
| 22. REMOVE FRONT DOOR LOCK |
![]() |
Using "TORX" socket wrench T30, remove the 3 screws.
Move the front door lock downward, remove the outside handle frame link and remove the front door lock.
![]() |
Open the cover.
![]() |
Disconnect the front door lock remote control cable and front door inside locking cable.
Remove the door lock wire harness seal.
| 23. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY |
![]() |
Remove the handle by sliding and pulling it in the directions indicated by the arrow mark in the illustration.
| 24. REMOVE FRONT DOOR OUTSIDE HANDLE PAD REAR |
![]() |
Disengage the 2 claws and remove the front door outside handle pad rear.
| 25. REMOVE FRONT DOOR OUTSIDE HANDLE PAD FRONT |
![]() |
Disengage the 2 claws and remove the front door outside handle pad front.
| 26. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY |
![]() |
Using "TORX" socket wrench T30, loosen the screw.
Slide the front outside handle frame to remove it.
| 27. REMOVE FRONT DOOR CHECK ASSEMBLY |
![]() |
Remove the 3 bolts, then remove the front door check.
| 28. REMOVE FRONT DOOR WEATHERSTRIP |
![]() |
Disengage the 35 clips and remove the front door weatherstrip.
| 29. REMOVE FRONT DOOR STIFFENER CUSHION (w/ Stiffener Cushion) |
![]() |
Remove the bolt and front door stiffener cushion.
| 30. REMOVE CUSHION |
![]() |
Remove the 2 cushions from the door panel.