Home › BODY › ENGINE HOOD / DOOR › FRONT DOOR (for Hatchback with Power Window)

FRONT DOOR (for Hatchback with Power Window) > REASSEMBLY

for Preparation Click here



1. INSTALL CUSHION
  1. Install the 2 cushions onto the door panel.



2. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


B116862
  1. Using "TORX" socket wrench T30, install the front outside handle frame with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



3. INSTALL FRONT DOOR OUTSIDE HANDLE PAD FRONT


B116840
  1. Engage the 2 claws and install the front door outside handle pad front.



4. INSTALL FRONT DOOR OUTSIDE HANDLE PAD REAR


B116839
  1. Engage the 2 claws and install the front door outside handle pad rear.



5. INSTALL FRONT DOOR HANDLE ASSEMBLY OUTSIDE


B116860
  1. Pushing the front door handle assembly outside in the direction of the arrow mark shown in the illustration, install the front door handle assembly outside.



6. INSTALL FRONT DOOR LOCK ASSEMBLY

NOTICE:
  1. If reusing a door lock that has been removed, replace the packing in the connecting part with new.
  2. Make sure that no grease and dirt adheres to the packing surface in the connecting part.

  1. Apply MP grease to the sliding and rotating areas of the front door lock.



    B121553
  1. Connect the front door lock remote control cable and front door inside locking cable.



    B121552
  1. Close the cover.



    B116845
  1. Insert the door lock open rod into the front door lock, then set it to the door panel.

    NOTICE:
    Make sure that the outside handle link is securely engaged with the door lock.



    B116836
  1. Apply adhesive to the threads of the screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Using "TORX" socket wrench T30, install the front door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



7. INSTALL FRONT DOOR OUTSIDE HANDLE COVER


B116858
  1. Using "TORX" socket wrench T30, install the cover with the door lock key cylinder.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    Make sure that the door lock key cylinder rod is inserted.

  1. Install the hole plug.



8. INSTALL FRONT DOOR FIX WINDOW WEATHERSTRIP
  1. Install the front door fix window glass onto the front door fix window weatherstrip.



    B116846
  1. Slide the front door fix window weatherstrip, in the direction indicated by the arrow in the illustration, to install it.



9. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY FRONT LOWER


B116832
  1. Install the front door frame sub-assembly front lower with the 2 bolts and screw.

    Torque:
    6.2 N*m{ 63 kgf*cm , 54 in.*lbf }



10. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER


B116831
  1. Install the front door frame sub-assembly rear lower with the bolt.

    Torque:
    6.2 N*m{ 63 kgf*cm , 54 in.*lbf }



11. INSTALL FRONT DOOR WEATHERSTRIP


B116833
  1. for 5 Door:
    Engage the 35 clips and install the front door weatherstrip.



    B116834
  1. for 3 Door:
    Engage the 37 clips and install the front door weatherstrip.



12. INSTALL FRONT DOOR CHECK ASSEMBLY


B116830
  1. Apply MP grease to the sliding areas of the door check.

  1. Install the front door check onto the door panel with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the front door check onto the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



13. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY FRONT


B209753
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using "TORX" socket wrench T25, install the power window regulator motor assembly front with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



14. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding and rotating areas of the front door window regulator.

    NOTICE:
    Do not apply grease to the window regulator spring.



    B116828E01
  1. Loosely screw bolt A onto the front door window regulator.

  1. Insert the front door window regulator into the door panel. Use bolt A to hang the front door window regulator on the door panel.

    NOTICE:
    Do not drop the window regulator as it may be damaged.

  1. Install the front door window regulator with the 5 bolts, and tighten bolt A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



15. INSTALL FRONT DOOR GLASS RUN


B116826
  1. Install the front door glass run.



16. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


B116847
  1. Insert the door glass into the door panel along the glass run as indicated by the arrows in the illustration.

    NOTICE:
    Do not damage the glass.



    B116825
  1. Install the front door glass onto the front door window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



17. INSTALL FRONT DOOR SERVICE HOLE COVER


B116848E01
  1. for 5 Door:
    Apply butyl tape to the door panel, then install the front door service hole cover as shown in the illustration.

    Specification:
    Area
    Dimension
    A
    2.0mm (0.079 in.) or more
    B
    6.0mm (0.236 in.) or more

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.



    B116849E01
  1. for 3 Door:
    Apply butyl tape to the door panel, then install the front door service hole cover as shown in the illustration.

    Specification:
    Area
    Dimension
    A
    2.0mm (0.079 in.) or more
    B
    6.0mm (0.236 in.) or more

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.



18. INSTALL FRONT DOOR BELT MOULDING


    B114401
  1. for 5 Door:

    1. Engage the 5 claws and the clip and install a new front door belt moulding.



    2. B114397E02
    3. Remove the protective tape.



    B114614
  1. for 3 Door:

    1. Engage the 5 claws and the clip and install a new front door belt moulding.



    2. B114612E01
    3. Remove the protective tape.



19. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY


B118045
  1. Engage the claw, then install the outer rear view mirror with the 3 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. w/ Power mirror:
    Connect the connector.



20. INSTALL FRONT DOOR WINDOW FRAME REAR MOULDING (for 3 Door)


    B114606E01
  1. Clean the attachment surface.

    1. Using an infrared light, heat the adhesive remaining on the body.

      NOTICE:
      Do not burn yourself with the heated body or infrared light.

    2. Using a shop rag or piece of cloth, rub the remaining adhesive off the body.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Apply new double-sided adhesive tape to the front door window frame rear moulding.
    Tape size: 
    Area
    t
    W
    H
    A
    0.8 mm (0.032 in.)
    5 mm (0.197 in.)
    340 mm (13.386 in.)
    B
    0.8 mm (0.032 in.)
    5 mm (0.197 in.)
    376 mm (14.803 in.)



    B114607
  1. Engage the 2 clips and the claw and install the front door window frame rear moulding.



21. INSTALL FRONT DOOR WINDOW FRAME FRONT MOULDING


    B127706E01
  1. Clean the attachment surface.

    1. Using an infrared light, heat the adhesive remaining on the body.

      NOTICE:
      Do not burn yourself with the heated body or infrared light.

    2. Using a shop rag or piece of cloth, rub the remaining adhesive off the body.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Apply new double-sided adhesive tape to the front door window frame front moulding.
    Tape size: 
    Area
    t
    W
    H
    A
    1.2 mm (0.047 in.)
    7 mm (0.276 in.)
    88 mm (3.465 in.)



    B127705E01
  1. Engage the 2 clips and the claw and install the front door window frame front moulding.



22. INSTALL FRONT NO.1 SPEAKER ASSEMBLY


    E107769E01
  1. Using an air riveter or hand riveter, install the front No. 1 speaker assembly onto the front door panel with 3 new strike rivets.

    HINT:
    Install the new strike rivets in the order shown in the illustration.

    NOTICE:

    1. H002440
      Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

    2. H002441
      Confirm that the rivets are seated properly against the speaker.
    3. Do not tilt the riveter when installing the rivet onto the speaker.
    4. Do not leave any space between the rivet head and speaker.

    5. H002442
      Do not leave any space between the speaker and door. Firmly hold the 2 items together while installing the rivet.



    E107770
  1. Connect the connector.



23. INSTALL FRONT DOOR GLASS WEATHERSTRIP INNER
  1. Install the front door glass weatherstrip inner onto the front door trim board.



24. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


B116945
  1. Engage the 6 claws and install the front door inside handle.



25. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


B127219
  1. Connect the front door lock remote control cable and front door inside locking cable.



    B116821
  1. 5 Door:
    Engage the 8 clips and install the front door trim board.



    B116822
  1. 3 Door:
    Engage the 9 clips and install the front door trim board.



    B107840
  1. Tighten the 4 screws.



26. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


B118070E02
  1. Install the power window regulator master switch with the 3 screws.



27. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY


B118071
  1. Engage the 2 claws and install the power window regulator switch.



28. INSTALL FRONT ARMREST BASE PANEL UPPER


B116819
  1. Connect the connector.

  1. Engage the 5 claws and clip and install the front armrest base panel upper.



29. INSTALL DOOR ARMREST COVER


B116818
  1. for 5 Door:
    Engage the 8 claws and 3 clips and install the door armrest cover.



    B116851
  1. for 3 Door:
    Engage the 12 claws and 4 clips and install the door armrest cover.



30. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }