Home › BODY › ENGINE HOOD / DOOR › FRONT DOOR (for Hatchback without Power Window)

FRONT DOOR (for Hatchback without Power Window) > DISASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the LH side.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE DOOR WINDOW REGULATOR HANDLE ASSEMBLY


B116850
  1. Insert a clip remover between the plate and door trim.

  1. Turn the handle with the clip remover inserted, as shown in the illustration.

  1. Remove the front door window regulator handle and clip.

  1. Remove the window regulator handle plate.



3. REMOVE DOOR ARMREST COVER


B116852
  1. for 5 Door:
    Using a screwdriver with its tip wrapped in protective tape, disengage the 8 claws and 3 clips and remove the door armrest cover.



    B116853
  1. for 3 Door:
    Disengage the 12 claws and 4 clips and remove the door armrest cover.



4. REMOVE FRONT ARMREST BASE PANEL UPPER


B116854
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 5 claws and clip and remove the front armrest base panel upper.



5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


B107840
  1. Remove the 4 screws.



    B116856
  1. for 5 Door:
    Disengage the 8 clips.



    B116855
  1. for 3 Door:
    Disengage the 9 clips.



    B127219
  1. Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door trim board.



6. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


B116945
  1. Disengage the 6 claws and remove the front door inside handle.



7. REMOVE FRONT DOOR GLASS WEATHERSTRIP INNER
  1. Remove the front door glass weatherstrip inner from the front door trim board.



8. REMOVE FRONT NO.1 SPEAKER ASSEMBLY


    E107768
  1. Disconnect the connector.

  1. Drill out the 3 rivet heads using a drill with a bit diameter of less than 4 mm (0.16 in.), and remove the front No.1 speaker assembly from the front door panel.

  1. Operate the drill around the rivet head circumference and cut out the flange.

    CAUTION:
    Be careful. The cut rivet is very hot.

    NOTICE:
    Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill the rivet head straight out.

  1. After drilling out the flange, continue drilling to push out the shards on the drill.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.



9. REMOVE FRONT DOOR WINDOW FRAME FRONT MOULDING


    B127705E01
  1. Using an infrared light, heat the front door window frame front moulding.

    CAUTION:
    Do not burn yourself with the heated front door panel or infrared light.

    HINT:
    Heat at 40 to 60 °C (104 to 140 °F) for 3 to 5 minutes.

  1. Disengage the 2 claws and remove the double-sided adhesive tape and the front door window frame front moulding.



10. REMOVE FRONT DOOR WINDOW FRAME REAR MOULDING (for 3 Door)


    B114605E01
  1. Using an infrared light, heat the front door window frame rear moulding.

    NOTICE:
    Do not burn yourself with the heated front door panel or infrared light.

    HINT:
    Heat at 40 to 60°C (104 to 140°F) for 3 to 5 minutes.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 clips and the claw and remove the double-sided adhesive tape and front door window frame rear moulding.



11. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY


B118045
  1. w/ Power mirror:
    Disconnect the connector.

  1. Remove the 3 nuts, disengage the claw and remove the outer rear view mirror.



12. REMOVE FRONT DOOR BELT MOULDING


    B114397E02
  1. for 5 Door:

    1. Apply protective tape to the door panel in the area around the front door belt moulding.



    2. B114398E02
    3. Using a moulding remover, disengage the 5 claws and the clip and remove the front door belt moulding.



    B114612E01
  1. for 3 Door:

    1. Apply protective tape to the door panel in the area around the front door moulding.



    2. B114613E01
    3. Using a moulding remover, disengage the 5 claws and remove the front door belt moulding.



13. REMOVE FRONT DOOR SERVICE HOLE COVER


B116823
  1. for 5 Door:
    Disconnect the connectors and clamps, then remove the front door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.



    B116824
  1. for 3 Door:
    Disconnect the connectors and clamps, then remove the front door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.



14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
  1. Provisionally install the front door window regulator handle.



    B116825
  1. Move the front door glass until the 2 bolts appear in the service holes.

  1. Remove the 2 bolts.

    NOTICE:
    Do not drop or damage the front door glass when removing the 2 bolts.



    B116827
  1. Remove the front door glass in the direction indicated by the arrows in the illustration.

    NOTICE:
    Do not damage the glass.

  1. Remove the front door window regulator handle.



15. REMOVE FRONT DOOR GLASS RUN


B116826
  1. Remove the front door glass run.



16. REMOVE FRONT DOOR WINDOW REGULATOR


B116857E01
  1. Loosen bolt A.

  1. Remove the 4 bolts, then remove the front door window regulator.

    NOTICE:
    Do not drop or damage the window regulator when removing the bolts.

    HINT:
    Remove the window regulator through the service hole.



17. REMOVE FRONT DOOR CHECK ASSEMBLY


B116830
  1. Remove the 3 bolts, then remove the front door check.

    NOTICE:
    Do not drop or damage the door check when removing the bolts.

    HINT:
    Remove the door check through the service hole.



18. REMOVE FRONT DOOR WEATHERSTRIP


B116833
  1. for 5 Door:
    Disengage the 35 clips and remove the front door weatherstrip.

    NOTICE:
    Remove any tape remaining on the door side.



    B116834
  1. for 3 Door:
    Disengage the 37 clips and remove the front door weatherstrip.

    NOTICE:
    Remove any tape remaining on the door side.



19. REMOVE FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER


B116831
  1. Remove the bolt, then remove the front door frame sub-assembly rear lower.

    NOTICE:
    Do not drop or damage the front door frame sub-assembly rear lower when removing the bolt.

    HINT:
    Remove the front door frame sub-assembly rear lower through the service hole.



20. REMOVE FRONT DOOR FRAME SUB-ASSEMBLY FRONT LOWER


B116832
  1. Remove the 2 bolts and screw, then remove the front door frame sub-assembly front lower.

    NOTICE:
    Do not drop or damage the front door frame sub-assembly front lower when removing the bolts.

    HINT:
    Remove the front door frame sub-assembly front lower through the service hole.



21. REMOVE FRONT DOOR FIX WINDOW WEATHERSTRIP


B116835
  1. Slide the front door fix window weatherstrip, in the direction indicated by the arrow in the illustration, to remove it.

  1. Remove the front door fix window glass from the front door fix window weatherstrip.



22. REMOVE FRONT DOOR OUTSIDE HANDLE COVER


B116858
  1. Remove the hole plug.

  1. Using "TORX" socket wrench T30, loosen the screw and remove the cover with the door lock key cylinder installed.



23. REMOVE FRONT DOOR LOCK ASSEMBLY


B116836
  1. Using "TORX" socket wrench T30, remove the 3 screws.

  1. Move the front door lock downward, remove the outside handle frame link and remove the front door lock.

    NOTICE:
    Do not drop or damage the front door lock when removing the screws.

    HINT:
    Remove the front door lock through the service hole.



    B121552
  1. Open the cover.



    B121553
  1. Disconnect the front door lock remote control cable and front door inside locking cable.

  1. Remove the door lock wire harness seal.



24. REMOVE FRONT DOOR HANDLE ASSEMBLY OUTSIDE


B116859
  1. Remove the handle by sliding and pulling it in the direction indicated by the arrow mark in the illustration.



25. REMOVE FRONT DOOR OUTSIDE HANDLE PAD REAR


B116839
  1. Disengage the 2 claws and remove the front door outside handle pad rear.



26. REMOVE FRONT DOOR OUTSIDE HANDLE PAD FRONT


B116840
  1. Disengage the 2 claws and remove the front door outside handle pad front.



27. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


B116861
  1. Using "TORX" socket wrench T30, loosen the screw.

  1. Slide the outside handle frame to remove it.



28. REMOVE CUSHION
  1. Remove the 2 cushions from the door panel.