Home › ENGINE ยท 2NZ-FE › ENGINE CONTROL SYSTEM › ECM

ECM > INSTALLATION

for Preparation Click here



1. INSTALL ECM BRACKET NO. 2


A115388
  1. Install ECM bracket No. 2 with the 2 screws.



2. INSTALL ECM BRACKET


A115387
  1. Install the ECM bracket with the 2 screws.



3. INSTALL ECM


A115386
  1. Install the ECM with the bolt and 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the 2 ECM connectors.



    A115385
  1. Install the 2 lock knobs and harness clamp.



4. INSTALL COWL TOP PANEL OUTER (for Hatchback)


A115392
  1. Install the cowl top panel with the 9 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }



    A108438
  1. Connect the wire harness clamp.



5. INSTALL COWL TOP PANEL OUTER (for Sedan)


A133328
  1. Install the cowl top panel outer and install the 8 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    A133326
  1. Install the cowl top panel outer center bracket and install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    A133322
  1. Connect the wire harness and engage the claw.



6. INSTALL FRONT AIR SHUTTER SEAL (for Sedan)


A133324
  1. Install the front air shutter seal and engage the 3 claws.



7. INSTALL COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2 (for Hatchback)


A108437
  1. Engage the claw to install cowl to register duct No. 2.



8. INSTALL WINDSHIELD WIPER MOTOR AND LINK (for Hatchback)


E113861
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



9. INSTALL WINDSHIELD WIPER MOTOR AND LINK (for Sedan)


    E127840
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



10. INSTALL COWL TOP VENTILATOR LOUVER LH (for Hatchback LHD)


E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.



11. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Hatchback LHD)


E113854
  1. Connect the washer hose.



    E113852
  1. Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.



    E117641
  1. Engage the 2 hooks and install cowl top ventilator louver center No. 1.



12. INSTALL COWL TOP VENTILATOR LOUVER LH (for Hatchback RHD)


E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.



13. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Hatchback RHD)


E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.



14. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan RHD)


    E127836
  1. Connect the washer hoses.

  1. Engage the 5 hooks.



    E127835
  1. Engage the 10 hooks and the 6 claws.

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.



15. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan LHD)


    E127839
  1. Connect the washer hoses.

  1. Engage the 5 hooks.



    E127838
  1. Engage the 8 hooks and the 4 claws.

  1. Install the cowl top ventilator louver sub-assembly with the 3 clips.



16. INSTALL HOOD TO COWL TOP SEAL (for Hatchback)


E113851
  1. Engage the 7 clips and install the hood to cowl top seal.



17. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH (for Sedan)


    E129651
  1. Engage the 3 claws and install the cowl side ventilator sub-assembly LH.



18. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH (for Sedan)

HINT:
Use the same procedure as for the LH side.



19. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH (for Hatchback)


E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113862E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



20. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH (for Sedan)


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113862E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



21. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (for Hatchback)


E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113863E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



22. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (for Sedan)


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E129694E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



23. INSTALL FRONT WIPER ARM HEAD CAP (for Hatchback)


E113849
  1. Engage the claw and install the 2 front wiper arm head caps.



24. INSTALL FRONT WIPER ARM HEAD CAP (for Sedan)


    E127841
  1. Engage the claw and install the 2 front wiper arm head caps.



25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }