ECM > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FRONT WIPER ARM HEAD CAP (for Hatchback) |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.
| 3. REMOVE FRONT WIPER ARM HEAD CAP (for Sedan) |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.
| 4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH (for Hatchback) |
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Remove the nut and front wiper arm.
| 5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH (for Sedan) |
![]() |
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Remove the nut and front wiper arm.
| 6. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH (for Hatchback) |
| 7. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH (for Sedan) |
| 8. REMOVE HOOD TO COWL TOP SEAL (for Hatchback) |
![]() |
Disengage the 7 clips and remove the hood to cowl top seal.
| 9. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH (for Sedan) |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.
| 10. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH (for Sedan) |
| 11. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Hatchback LHD) |
![]() |
Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.
![]() |
Disconnect the washer hose.
Disengage the 11 claws and clip.
![]() |
Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.
| 12. REMOVE COWL TOP VENTILATOR LOUVER LH (for Hatchback LHD) |
![]() |
Remove the 2 clips.
Disengage the 4 claws and remove the cowl top ventilator louver LH.
| 13. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Hatchback RHD) |
![]() |
Disconnect the washer hose.
Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.
| 14. REMOVE COWL TOP VENTILATOR LOUVER LH (for Hatchback RHD) |
![]() |
Remove the clip.
Disengage the 4 claws and remove the cowl top ventilator louver LH.
| 15. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan RHD) |
![]() |
Disengage the 2 clips, the 6 claws and the 10 hooks.
Remove the cowl top ventilator louver sub-assembly.
![]() |
Disconnect the washer hoses.
Disengage the 5 hooks.
| 16. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan LHD) |
![]() |
Disengage the 3 clips, the 4 claws and the 8 hooks.
Remove the cowl top ventilator louver sub-assembly.
![]() |
Disconnect the washer hoses.
Disengage the 5 hooks.
| 17. REMOVE WINDSHIELD WIPER MOTOR AND LINK (for Hatchback) |
![]() |
Remove the 2 bolts.
Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.
| 18. REMOVE WINDSHIELD WIPER MOTOR AND LINK (for Sedan) |
![]() |
Remove the 2 bolts.
Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.
| 19. REMOVE COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2 (for Hatchback) |
![]() |
Disengage the claw and remove cowl to register duct sub-assembly No. 2.
| 20. REMOVE FRONT AIR SHUTTER SEAL (for Sedan) |
![]() |
Disengage 3 claws and remove the front air shutter seal.
| 21. REMOVE COWL TOP PANEL OUTER (for Hatchback) |
![]() |
Disengage the wire harness clamp.
![]() |
Remove the 9 bolts and remove the cowl top panel outer.
| 22. REMOVE COWL TOP PANEL OUTER (for Sedan) |
![]() |
Disengage the claw and disconnect the wire harness.
![]() |
Remove the 2 bolts and remove the cowl top panel outer center bracket.
![]() |
Remove the 8 bolts and remove the cowl top panel outer.
| 23. REMOVE ECM |
![]() |
Remove the 2 lock knobs and harness clamp.
Disconnect the 2 ECM connectors.
![]() |
Remove the bolt and 2 nuts and remove the ECM.
| 24. REMOVE ECM BRACKET |
![]() |
Remove the 2 screws and the ECM bracket.
| 25. REMOVE ECM BRACKET NO. 2 |
![]() |
Remove the 2 screws and ECM bracket No. 2.