CYLINDER HEAD > INSTALLATION |
| 1. INSTALL INJECTOR VIBRATION INSULATOR |
![]() |
Install 4 new injector vibration insulators onto the cylinder head.
| 2. INSTALL DELIVERY PIPE NO. 1 SPACER |
![]() |
Install the 2 delivery pipe No. 1 spacers onto the cylinder head.
| 3. INSTALL FUEL INJECTOR ASSEMBLY |
![]() |
Apply a light coat of gasoline or spindle oil to new O-rings, then install one onto each fuel injector.
Apply a light coat of gasoline or spindle oil to the contact surfaces of the fuel delivery pipe and the O-ring of the fuel injector.
![]() |
While turning the fuel injector left and right, install it onto the fuel delivery pipe.
| 4. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY |
![]() |
Provisionally install the fuel delivery pipe sub-assembly with the 4 fuel injectors using the 3 bolts.
![]() |
Tighten the 3 bolts to the specified torque.
| 5. INSTALL HARNESS BRACKET |
![]() |
Install the harness bracket with the bolt.
| 6. INSTALL WATER BY-PASS HOSE |
![]() |
Install the water by-pass hose.
| 7. INSTALL ENGINE COOLANT TEMPERATURE SENSOR |
![]() |
Provisionally install the engine coolant temperature sensor through a new gasket.
Using SST, tighten the engine coolant temperature sensor.
| 8. INSTALL CAMSHAFT POSITION SENSOR |
![]() |
Apply a light coat of engine oil to the O-ring on the camshaft position sensor.
Install the camshaft position sensor with the bolt.
| 9. INSTALL BOOSTER VACUUM TUBE |
![]() |
Install the booster vacuum tube with the 2 bolts.
| 10. INSTALL HARNESS BRACKET |
![]() |
Install the harness bracket with the bolt.
| 11. INSTALL EXHAUST MANIFOLD |
![]() |
Using several steps, install a new exhaust manifold gasket and exhaust manifold with the 3 bolts and 2 nuts in the sequence shown in the illustration.
| 12. INSTALL EXHAUST MANIFOLD HEAT INSULATOR NO. 1 |
![]() |
Install exhaust manifold heat insulator No. 1 with the 3 bolts.
| 13. INSTALL CYLINDER HEAD GASKET |
![]() |
Place a new cylinder head gasket on the cylinder block with the Lot No. stamp facing upward.
| 14. INSTALL CYLINDER HEAD SUB-ASSEMBLY |
Apply a light coat of engine oil to the threads of the cylinder head bolts.
![]() |
Using several steps, install and tighten the 10 cylinder head bolts and plate washers uniformly with an 8 mm bi-hexagon wrench, in the sequence shown in the illustration.
Mark the front of the cylinder head bolt with paint.
![]() |
Retighten the cylinder head bolts 90° and then an additional 90° as shown in the illustration.
Check that the paint mark is now at a 180° angle from the front.
![]() |
Apply a continuous bead of seal packing (Diameter 4.5 to 5.5 mm (0.177 to 0.217 in.)) as shown in the illustration.
| 15. INSTALL CAMSHAFT |
![]() |
Examine the front marks and numbers and check that the sequence is as shown in the illustration. Then provisionally tighten the bolts.
![]() |
Uniformly tighten the bolts in several steps in the sequence shown in the illustration and install camshaft bearing cap No. 1 and camshaft bearing cap No. 2.
| 16. INSTALL CHAIN SUB-ASSEMBLY |
![]() |
for Unleaded Gasoline Specification Vehicle:
Make sure that all the timing marks are in the positions (TDC) shown in the illustration.
![]() |
for Leaded Gasoline Specification Vehicle:
Make sure that each timing mark is in the position (TDC) shown in the illustration.
![]() |
Set the timing mark of the crankshaft in a position between 40 and 140°ATDC as illustrated.
![]() |
for Unleaded Gasoline Specification Vehicle:
Set the camshaft timing gear and the camshaft timing sprocket in the positions (20°ATDC) shown in the illustration.
for Unleaded Gasoline Specification Vehicle:
Set the crankshaft in the position (20°ATDC) shown in the illustration.
![]() |
for Leaded Gasoline Specification Vehicle:
Set the camshaft timing sprockets in the position (20°ATDC) shown in the illustration.
for Leaded Gasoline Specification Vehicle:
Set the camshaft in the position (20°ATDC) shown in the illustration.
![]() |
Install chain vibration damper No. 1 with the 2 bolts.
![]() |
for Unleaded Gasoline Specification Vehicle:
Align the timing marks of the camshaft with the mark plates of the timing chain and install the timing chain.
![]() |
for Leaded Gasoline Specification Vehicle:
Align the timing marks of the camshaft with the mark plates of the timing chain and install the timing chain.
| 17. INSTALL CHAIN TENSIONER SLIPPER |
![]() |
Install the chain tensioner slipper.
| 18. INSTALL CHAIN TENSIONER ASSEMBLY NO. 1 |
![]() |
Install chain tensioner assembly No. 1 with the 2 bolts.
Remove the bar from chain tensioner assembly No. 1.
| 19. INSTALL OIL PUMP SEAL |
![]() |
Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.
Apply a light coat of MP grease to the oil pump seal lip.
| 20. INSTALL OIL PUMP ASSEMBLY |
![]() |
Install 2 new O-rings onto the 2 locations shown in the illustration.
Apply seal packing to the oil pump assembly, cylinder head and cylinder block as shown in the illustration.

![]() |
Align the keyway of the oil pump rotor with the rectangular portion of the crankshaft, and slide the oil pump into place.
![]() |
Install the oil pump assembly with the 15 bolts and the nut. Tighten the bolts and nut uniformly in several steps.
| 21. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET |
![]() |
Install the transverse engine engine mounting bracket with the 4 bolts.
| 22. INSTALL WATER PUMP ASSEMBLY |
![]() |
Install the water pump assembly through a new gasket with the 3 bolts and 2 nuts.
| 23. INSTALL WATER PUMP PULLEY |
Provisionally install the water pump pulley with the 3 bolts.
![]() |
Using SST, hold the water pump pulley.
Tighten the 3 bolts to the specified torque.
| 24. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Unleaded Gasoline Specification Vehicle) |
![]() |
Apply a light coat of engine oil to a new O-ring and install it onto the camshaft timing oil control valve assembly.
![]() |
Install the camshaft timing oil control valve assembly with the bolt.
![]() |
Connect the camshaft timing oil control valve assembly connector.
| 25. INSTALL CRANKSHAFT POSITION SENSOR |
![]() |
Apply a light coat of engine oil to the O-ring on the crankshaft position sensor.
Install the crankshaft position sensor with the bolt.
Connect the crankshaft position sensor connector.
| 26. INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY |
Align the pin hole of the crankshaft damper with the pin and install the crankshaft damper sub-assembly.
Provisionally install the bolt.
![]() |
Using 2 SSTs, tighten the bolt while holding the crankshaft damper sub-assembly.
| 27. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
![]() |
Install the engine mounting insulator sub-assembly RH with the 5 bolts and nut.
| 28. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for RHD) |
![]() |
Apply seal packing to the cylinder head as shown in the illustration.
Install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 seal washers.
![]() |
Tighten the 9 bolts and 2 nuts in the sequence shown in the illustration.
![]() |
Connect the connector and wire harness clamp shown in the illustration and connect the engine wire harness.
![]() |
Connect the fuel injector connectors.
| 29. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for LHD) |
![]() |
Apply seal packing to the cylinder head as shown in the illustration.
Install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 seal washers.
![]() |
Tighten the 9 bolts and 2 nuts in the sequence shown in the illustration.
![]() |
Install the wire harness bracket with the bolt.
![]() |
Connect the connector and wire harness clamp shown in the illustration and connect the engine wire harness.
![]() |
Connect the fuel injector connectors.
| 30. INSTALL VENTILATION HOSE NO. 2 |
![]() |
Connect ventilation hose No. 2.
| 31. INSTALL VENTILATION HOSE |
![]() |
Connect the ventilation hose.
| 32. INSTALL IGNITION COIL NO. 1 |
![]() |
Install the 4 ignition coils with the 4 bolts.
![]() |
Connect the 4 ignition coil connectors.
| 33. INSTALL GENERATOR ASSEMBLY |
![]() |
Provisionally install the generator with fixing bolt B.
![]() |
Provisionally install the fan belt adjusting slider with fan belt adjusting slider fixing bolts A and B, then move the generator toward the cylinder block and tighten bolt B.
![]() |
Install the connector and wire harness clamp.
Install terminal B with the nut.
Install the terminal cap.
Close the terminal cap.
| 34. INSTALL FAN & GENERATOR V BELT |
Provisionally install the fan and generator V belt onto each pulley.
| 35. ADJUST FAN & GENERATOR V BELT |
![]() |
for Unleaded Gasoline Specification Vehicle:
Insert an adjusting bar between the engine mounting bracket and generator assembly. Pull the adjusting bar towards the vehicle front to adjust the generator V belt tension.
![]() |
for Leaded Gasoline Specification Vehicle:
Insert the adjusting bar between the engine mounting bracket and generator assembly. Pull the adjusting bar towards the vehicle front to adjust the generator V belt tension.
![]() |
First tighten bolt A, then tighten bolt B.
| 36. INSPECT FAN & GENERATOR V BELT |
![]() |
Check the V belt deflection and tension.
| Item | Specified Condition |
| New belt | 8.0 to 9.0 mm (0.31 to 0.35 in) |
| Used belt | 12.5 to 13.5 mm (0.49 to 0.53 in) |
| Item | Specified Condition |
| New belt | 700 to 800 N (71 to 82 kg, 157 to 180 lb) |
| Used belt | 300 to 400 N (31 to 41 kg, 67 to 90 lb) |
| 37. INSTALL MANIFOLD SUPPORT BRACKET |
![]() |
Install the manifold support bracket with the 3 bolts.
| 38. INSTALL EXHAUST PIPE ASSEMBLY FRONT |
![]() |
Using vernier calipers, measure the free length of the compression spring.
![]() |
Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.
![]() |
Install the exhaust front pipe assembly with the 2 compression springs and 2 bolts.
| 39. CONNECT WIRE HARNESS |
![]() |
Connect the wire harness with the 2 bolts.
| 40. INSTALL WATER BY-PASS PIPE NO. 1 |
![]() |
Install water by-pass pipe No. 1 with the bolt.
| 41. CONNECT HEATER WATER HOSE INLET A |
![]() |
Connect heater water inlet hose A.
| 42. CONNECT HEATED OXYGEN SENSOR CONNECTOR (for Unleaded Gasoline Specification Vehicle) |
![]() |
Connect the heated oxygen sensor connector.
Install the sensor bracket with the bolt.
| 43. CONNECT ENGINE COOLANT TEMPERATURE SENSOR CONNECTOR |
![]() |
Connect the engine coolant temperature sensor connector.
| 44. CONNECT CAMSHAFT POSITION SENSOR CONNECTOR |
![]() |
Connect the camshaft position sensor connector.
| 45. CONNECT BOOSTER VACUUM TUBE |
![]() |
Connect the booster vacuum tube.
| 46. CONNECT FUEL TUBE SUB-ASSEMBLY |
![]() |
Insert the fuel tube connector into the fuel delivery pipe until a click sound can be heard.
![]() |
Install the fuel pipe clamp.
| 47. INSTALL OIL LEVEL GAGE GUIDE |
![]() |
Apply engine oil to a new O-ring.
Install the oil level gauge guide with the bolt through a new O-ring.
Install the wire harness.
| 48. INSTALL INTAKE MANIFOLD |
Install a new gasket onto the intake manifold.
![]() |
Install the intake manifold with the 3 bolts and 2 nuts.
![]() |
Connect the wire harness clamp shown in the illustration.
| 49. INSTALL OIL LEVEL GAUGE SUB-ASSEMBLY |
| 50. CONNECT UNION TO CONNECTOR TUBE HOSE |
![]() |
Connect the union to connector tube hose.
| 51. CONNECT VENTILATION HOSE |
![]() |
Connect the ventilation hose.
| 52. CONNECT THROTTLE WITH MOTOR BODY CONNECTOR |
![]() |
Install the throttle with motor body connector bracket with the nut.
Connect the throttle with motor body connector.
Connect the wire harness clamp.
| 53. CONNECT WATER BY-PASS HOSE |
![]() |
Connect the water by-pass hose.
| 54. CONNECT WATER BY-PASS HOSE NO. 2 |
![]() |
Connect water by-pass hose No. 2.
| 55. INSTALL WATER FILLER SUB-ASSEMBLY |
![]() |
Install the water filler sub-assembly with the 2 nuts.
Connect radiator hose No. 1 to the cylinder head.
| 56. CONNECT RESERVE TANK HOSE |
![]() |
Connect the reserve tank hose.
| 57. CONNECT RADIATOR HOSE NO. 3 |
![]() |
Connect radiator hose No. 3.
| 58. INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE NO. 1 |
![]() |
Install air cleaner cap sub-assembly with air cleaner hose No. 1.
Tighten the hose clamp to the specified torque.
![]() |
Connect the wire harness clamp and mass air flow meter connector.
![]() |
Connect ventilation hose No. 2.
![]() |
Connect the vacuum switching valve assembly connector and wire harness clamp.
Connect fuel vapor feed hose No. 1 and fuel vapor feed hose No. 2 to the vacuum switching valve assembly.
| 59. INSTALL BATTERY TRAY |
| 60. INSTALL BATTERY |
| 61. ADD ENGINE OIL |
| 62. ADD ENGINE COOLANT |
Tighten all the plugs.
Pour engine coolant into the radiator assembly until it overflows.
Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.
Install the radiator cap sub-assembly securely.
Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.
Warm up the engine until the cooling fan operates.
Set the air conditioning as follows while warming up the engine.
| Item | Manual air conditioning system | Automatic air conditioning system |
| Set control as follows | Fan speed - Any setting except "OFF" Temperature - Toward WARM Air conditioning switch "OFF" | Fan speed - Any setting except "OFF" Temperature - To the highest temperature Air conditioning switch "OFF" "AUTO" switch "OFF" |
Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.
Stop the engine and wait until the coolant cools down.
If the engine coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the engine coolant level stays at the full level.
Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add the engine coolant.
| 63. CHECK ENGINE OIL LEVEL |
Warm up the engine, then stop the engine and wait for 5 minutes. Check that the engine oil level is between the low and full marks on the oil level gauge.
If the engine oil level is low, check for oil leakage and add engine oil up to the full level mark.
| 64. CHECK FOR ENGINE OIL LEAKAGE |
| 65. CHECK FOR ENGINE COOLANT LEAKAGE |
![]() |
Fill the radiator assembly with engine coolant, then attach a radiator cap tester.
Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
| 66. CHECK FOR EXHAUST GAS LEAKAGE |
| 67. CHECK FOR FUEL LEAKAGE |
When using the intelligent tester.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and intelligent tester main switch on.
Select the Active Test mode on the intelligent tester.
Check that there is no fuel leakage anywhere on the fuel system after doing maintenance.
| 68. INSTALL CYLINDER HEAD COVER NO. 2 |
![]() |
Tighten 2 A nuts, then 2 B nuts.
| 69. INSTALL ENGINE UNDER COVER RH |
| 70. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY (for Rough Road Area Specification Vehicles) |
| 71. INSTALL FRONT WHEEL RH |
| 72. INSTALL COWL TOP PANEL OUTER (for Hatchback) |
![]() |
Install the cowl top panel with the 9 bolts.
![]() |
Connect the wire harness clamp.
| 73. INSTALL COWL TOP PANEL OUTER (for Sedan) |
| 74. INSTALL FRONT AIR SHUTTER SEAL RH (for Sedan) |
| 75. INSTALL COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2 (for Hatchback) |
![]() |
Engage the claw to install cowl to register duct No. 2.
| 76. INSTALL FRONT AIR SHUTTER SEAL RH (for Sedan LHD) |
| 77. INSTALL FRONT WIPER MOTOR AND LINK (for Hatchback) |
![]() |
Connect the connector.
Slide the wiper link as shown in the illustration and engage the rubber pin with the body.
Install the front wiper motor and link with the 2 bolts.
| 78. INSTALL FRONT WIPER MOTOR AND LINK (for Sedan) |
![]() |
Connect the connector.
Slide the wiper link as shown in the illustration and engage the rubber pin with the body.
Install the front wiper motor and link with the 2 bolts.
| 79. INSTALL COWL TOP VENTILATOR LOUVER LH (for Hatchback LHD) |
![]() |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the 2 clips.
| 80. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Hatchback LHD) |
![]() |
Connect the washer hose.
![]() |
Engage the 11 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
![]() |
Engage the 2 hooks and install cowl top ventilator louver center No. 1.
| 81. INSTALL COWL TOP VENTILATOR LOUVER LH (for Hatchback RHD) |
![]() |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the clip.
| 82. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Hatchback RHD) |
![]() |
Engage the 10 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
| 83. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan RHD) |
![]() |
Connect the washer hoses.
Engage the 5 hooks.
![]() |
Engage the 10 hooks and the 6 claws.
Install the cowl top ventilator louver sub-assembly with the 2 clips.
| 84. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan LHD) |
![]() |
Connect the washer hoses.
Engage the 5 hooks.
![]() |
Engage the 8 hooks and the 4 claws.
Install the cowl top ventilator louver sub-assembly with the 3 clips.
| 85. INSTALL HOOD TO COWL TOP SEAL (for Hatchback) |
![]() |
Engage the 7 clips and install the hood to cowl top seal.
| 86. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH (for Sedan) |
![]() |
Engage the 3 claws and install the cowl side ventilator sub-assembly LH.
| 87. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBY RH (for Sedan) |
| 88. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH (for Hatchback) |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 89. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH (for Sedan) |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 90. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (for Hatchback) |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 91. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (for Sedan) |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 92. INSTALL FRONT WIPER ARM HEAD CAP (for Hatchback) |
![]() |
Engage the claw and install the 2 front wiper arm head caps.
| 93. INSTALL FRONT WIPER ARM HEAD CAP (for Sedan) |
![]() |
Engage the claw and install the 2 front wiper arm head caps.