OIL PUMP > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FRONT WHEEL RH |
| 3. REMOVE ENGINE UNDER COVER RH |
| 4. REMOVE ENGINE UNDER COVER SUB-ASSEMBLY (for Rough Road Area Specification Vehicles) |
| 5. DRAIN ENGINE OIL |
| 6. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug.
Remove the radiator cap sub-assembly.
Loosen the cylinder block drain cock plug, then drain the coolant.

| 7. REMOVE CYLINDER HEAD COVER NO. 2 |
![]() |
Remove the 4 nuts and cylinder head cover No. 2.
| 8. REMOVE FAN & GENERATOR V BELT |
![]() |
Loosen bolts A and B.
Release the fan and generator V belt tension and remove the fan and generator V belt.
| 9. REMOVE GENERATOR ASSEMBLY |
![]() |
Remove the terminal cap.
Separate the connector and harness clamp.
Remove the nut and remove terminal B.
![]() |
Remove fan belt adjusting slider fixing bolts A and B and remove the fan belt adjusting slider.
![]() |
Remove fixing bolt B and remove the generator.
| 10. REMOVE IGNITION COIL NO. 1 |
![]() |
Disconnect the 4 ignition coil connectors.
![]() |
Remove the 4 bolts and 4 ignition coils.
| 11. DISCONNECT VENTILATION HOSE |
![]() |
Disconnect the ventilation hose.
| 12. DISCONNECT VENTILATION HOSE NO. 2 |
![]() |
Disconnect ventilation hose No. 2.
| 13. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for RHD) |
![]() |
Disconnect the fuel injector connectors.
![]() |
Disconnect the connector and 3 wire harness clamps shown in the illustration and disconnect the engine wire harness.
![]() |
Remove the 9 bolts, 2 nuts and 2 seal washers and then remove the cylinder head cover sub-assembly.
| 14. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for LHD) |
![]() |
Disconnect the fuel injector connectors.
![]() |
Disconnect the connector and 3 wire harness clamps shown in the illustration and disconnect the engine wire harness.
![]() |
Remove the bolt and remove the wire harness bracket.
![]() |
Remove the 9 bolts and 2 nuts, 2 seal washers and then remove the cylinder head cover sub-assembly.
| 15. REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
![]() |
Place a wooden block on a jack underneath the engine.
![]() |
Remove the 5 bolts and nut and remove the engine mounting insulator sub-assembly RH.
| 16. REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY |
![]() |
Set cylinder No. 1 to TDC/compression.
Turn the crankshaft damper sub-assembly, and align its timing notch with timing mark "0" of the oil pump.
![]() |
for Unleaded Gasoline Specification Vehicle:
Check that the timing marks on the camshaft timing sprocket and the camshaft timing gear are all facing upward as shown in the illustration.
![]() |
for Leaded Gasoline Specification Vehicle:
Check that both timing marks on the camshaft timing sprockets facing upward as shown in the illustration.
![]() |
Using 2 SSTs, loosen the bolt while holding the crankshaft damper sub-assembly.
Remove the SSTs and the bolt.
Remove the crankshaft damper sub-assembly.
| 17. REMOVE CRANKSHAFT POSITION SENSOR |
![]() |
Disconnect the crankshaft position sensor connector.
Remove the bolt and remove the crankshaft position sensor.
| 18. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Unleaded Gasoline Specification Vehicle) |
![]() |
Disconnect the camshaft timing oil control valve assembly connector.
![]() |
Remove the bolt and nut and remove the camshaft timing oil control valve assembly.
![]() |
Remove the O-ring from the camshaft timing oil control valve assembly.
| 19. REMOVE WATER PUMP PULLEY |
![]() |
Using SST, hold the water pump pulley.
Remove the 3 bolts and remove the water pump pulley.
| 20. REMOVE WATER PUMP ASSEMBLY |
![]() |
Remove the 3 bolts and 2 nuts and remove the water pump assembly and gasket.
| 21. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET |
![]() |
Remove the 4 bolts and remove the transverse engine engine mounting bracket.
| 22. REMOVE OIL PUMP ASSEMBLY |
![]() |
Remove the 15 bolts and the nut.
![]() |
Using a screwdriver with its tip wrapped in protective tape, prize the oil pump assembly to remove it.
![]() |
Remove the 2 O-rings from the cylinder block and oil pan sub-assembly.