Home › ENGINE ยท 1NZ-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE SPARK PLUG


A080968E01
  1. Using a spark plug wrench, remove the 4 spark plugs.



2. REMOVE KNOCK SENSOR


A117462
  1. Remove the nut and remove the knock sensor.



3. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY


A117463
  1. Using a 24 mm deep socket wrench, remove the oil pressure switch.



4. REMOVE ENGINE COOLANT TEMPERATURE SENSOR


A117464E01
  1. Using SST, remove the engine coolant temperature sensor.

    SST
    09817-33190  



5. REMOVE WATER INLET


A080960E01
  1. Remove the 2 nuts and remove the water inlet.



6. REMOVE THERMOSTAT


A116187
  1. Remove the thermostat.

  1. Remove the gasket from the thermostat.



7. REMOVE OIL FILLER CAP SUB-ASSEMBLY


A080967E01
  1. Remove the oil filler cap from the cylinder head cover.



8. REMOVE OIL FILLER CAP GASKET


A065656E01
  1. Using a screwdriver, remove the gasket from the oil filler cap.



9. REMOVE CRANKSHAFT POSITION SENSOR
  1. Remove the bolt and the crankshaft position sensor.



10. REMOVE VENTILATION VALVE SUB-ASSEMBLY


A080963E01
  1. Remove the ventilation valve from the cylinder head cover.



11. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


A066472E01
  1. Remove the 9 bolts, 2 nuts and 2 seal washers and then remove the cylinder head cover sub-assembly.



12. REMOVE CYLINDER HEAD COVER GASKET
  1. Remove the gasket from the cylinder head cover.



13. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


A064872E01
  1. Remove the bolt and the camshaft timing oil control valve.



14. REMOVE OIL LEVEL GAUGE GUIDE
  1. Remove the bolt and the oil level gauge guide.



15. REMOVE WATER PUMP PULLEY


A116191E01
  1. Using SST, hold the pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the 3 bolts and the pump pulley.



16. REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY


A116203E01


  1. Set cylinder No. 1 to TDC/compression.

    1. Turn the crankshaft damper sub-assembly, and align its timing notch with timing mark "0" of the oil pump.



    2. A116204E01
    3. Check that the timing marks on the camshaft timing sprocket and the camshaft timing gear are all facing upward, as shown in the illustration.
      If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.



    A117461E01
  1. Using 2 SSTs, loosen the bolt while holding the crankshaft damper sub-assembly.

    SST
    09213-14010   (91651-60865)
    09330-00021  

    NOTICE:
    Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump assembly.

  1. Remove the SSTs and the bolt.

  1. Remove the crankshaft damper sub-assembly.



17. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET


A080957E01
  1. Remove the 4 bolts and remove the transverse engine mounting bracket.



18. REMOVE WATER PUMP ASSEMBLY


A116192
  1. Remove the 3 bolts and 2 nuts and remove the water pump and gasket.



19. REMOVE OIL PUMP ASSEMBLY


A116554
  1. Remove the 15 bolts and nut.



    A050903E01
  1. Using a screwdriver with its tip wrapped in protective tape, prize the oil pump assembly to remove it.

    NOTICE:
    Do not damage the contact surface of the oil pump assembly and oil pan sub-assembly.



    A116556
  1. Remove the 2 O-rings from the cylinder block and oil pan sub-assembly.



20. REMOVE OIL PUMP SEAL


A035281E04
  1. Using a screwdriver with its tip wrapped in protective tape, remove the oil seal.



21. REMOVE CHAIN TENSIONER ASSEMBLY NO. 1


A050142E06

NOTICE:
  1. Do not rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first.



    A116564E01
  1. Pull up the stopper plate and hold it with its lock released.



    A116565E01
  1. Unlock the plunger of the tensioner and push it in to the end.



    A116566E01
  1. Pull down the stopper plate with the plunger pushed to the end and lock the plunger.



    A116567
  1. Insert a 3 mm (0.12 in.) diameter bar into the hole in the stopper plate and lock the plunger.



    A116568
  1. Remove the 2 bolts and remove chain tensioner assembly No. 1.



22. REMOVE CHAIN TENSIONER SLIPPER


A116569
  1. Remove the chain tensioner slipper.



23. REMOVE CHAIN VIBRATION DAMPER NO. 1


A116570
  1. Remove the 2 bolts and remove chain vibration damper No. 1.



24. REMOVE CHAIN SUB-ASSEMBLY


25. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


A115494
  1. Remove the 3 bolts and remove the fuel delivery pipe sub-assembly together with the 4 fuel injectors.

    NOTICE:
    Do not drop the fuel injectors when removing the fuel delivery pipe sub-assembly.



26. REMOVE DELIVERY PIPE NO. 1 SPACER


A115496
  1. Remove the 2 delivery pipe No. 1 spacers.



27. REMOVE INJECTOR VIBRATION INSULATOR


A115497
  1. Remove the 4 injector vibration insulators.



28. REMOVE FUEL INJECTOR ASSEMBLY


A115498E01
  1. Pull the 4 fuel injector assemblies out of the fuel delivery pipe sub-assembly.



29. REMOVE CAMSHAFT POSITION SENSOR


A080958E01
  1. Remove the bolt and the camshaft position sensor.



30. REMOVE NO. 2 CAMSHAFT


A050142E06

NOTICE:
When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first, and align the oil jet hole with the paint mark. This prevents the pistons from coming into contact with the valves.



    A037074E01
  1. Using several steps, loosen and remove the 11 bearing cap bolts uniformly in the sequence shown in the illustration, then remove camshaft bearing cap No. 1, camshaft bearing cap No. 2 and camshaft No. 2.

    NOTICE:
    Loosen each bolt uniformly while keeping the camshaft level.



31. REMOVE CAMSHAFT TIMING SPROCKET


A064874E01
  1. Clamp the camshaft in a vice.

  1. Remove the flange bolt and the camshaft timing sprocket.

    NOTICE:
    Do not damage the camshaft.



32. REMOVE CAMSHAFT


A037075E01
  1. Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence shown in the illustration, then remove camshaft bearing cap No. 2 and the camshaft.

    NOTICE:
    Loosen each bolt uniformly keeping the camshaft level.



33. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Clamp the camshaft in a vise, and confirm that it is locked.

    NOTICE:
    Do not damage the camshaft.



    A116226E04
  1. Cover the 4 oil paths of the cam journal with tape as shown in the illustration.

    HINT:
    One of the 2 grooves located on the cam journal is for retarding cam timing (upper) and the other is for advancing cam timing (lower). Each groove has 2 oil paths. Plug one of the oil paths for each groove with a piece rubber before wrapping the cam journal with the tape.

  1. Puncture the tape covering the advance oil path and the retard oil path on the opposite side from the advance oil path.



    A116227E02
  1. Apply at about 150 kPa (1.5 kgf*cm2) air pressure into the 2 broken paths (the advance side path and the retard side path).

    NOTICE:
    Cover the paths with a shop rag or piece of cloth to prevent oil splashes.



    A116228E02
  1. Confirm that the camshaft timing gear assembly revolves in the timing advance direction when the air pressure on the timing retard path is reduced.

    HINT:
    The lock pin is released and the camshaft timing gear revolves in the advance direction.

  1. When the camshaft timing gear reaches the most advanced position, release the air pressure on the timing retard side path, and then release the air pressure on the timing advance side path.

    NOTICE:
    Camshaft timing gear assembly occasionally shifts to the retard side abruptly if the air pressure on the advance side path is released first. It often results in the breakage of the lock pin.



    A116229E01
  1. Remove the flange bolt and remove the camshaft timing gear assembly.

    NOTICE:
    1. Do not remove the other 4 bolts.
    2. When reusing the camshaft timing gear, unlock the lock pin inside the camshaft timing gear first.



34. REMOVE CYLINDER HEAD SUB-ASSEMBLY


A035286E01
  1. Using several steps, loosen and remove the 10 cylinder head bolts uniformly with an 8 mm bi-hexagon wrench in the sequence shown in the illustration. Remove the 10 cylinder head bolts and the plate washers.

    NOTICE:
    1. Do not drop the washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in the wrong order.



35. REMOVE CYLINDER HEAD GASKET


36. REMOVE OIL FILTER SUB-ASSEMBLY


A038018E02
  1. Using SST, remove the oil filter.

    SST
    09228-06501  



37. REMOVE OIL FILTER UNION


A079679E01
  1. Using a 12 mm hexagon wrench, remove the oil filter union.



38. REMOVE ENGINE REAR OIL SEAL


A051764E01
  1. Using a knife, cut off the oil seal lip.

  1. Using a screwdriver with its tip wrapped in tape, pry out the oil seal.

    NOTICE:
    After removal, check the crankshaft for any damage. If damaged, smooth the surface with 400-grit sandpaper.



39. REMOVE OIL PAN SUB-ASSEMBLY NO. 2
  1. Remove the oil pan drain plug and gasket.



    A079680E01
  1. Remove the 9 bolts and 2 nuts.



    A001456E01
  1. Insert the blade of an oil pan seal cutter between the No. 1 oil pan and No. 2 oil pan, and cut off the applied sealer and remove No. 2 oil pan.

    NOTICE:
    Do not damage oil pan No. 1 or oil pan No. 2.



40. REMOVE OIL STRAINER SUB-ASSEMBLY
  1. Remove the bolt and 2 nuts.

  1. Remove the oil strainer and the gasket.



41. REMOVE OIL PAN SUB-ASSEMBLY


A050902E01
  1. Loosen and remove the 13 bolts uniformly in several steps.



    A011272E01
  1. Using a screwdriver, remove oil pan No. 1 by prying between the cylinder block and oil pan No. 1.

    NOTICE:
    Do not damage the contact surfaces of oil pan No. 1 or the cylinder block.

  1. Remove the 2 O-rings from the cylinder block.



42. REMOVE STUD BOLT


A117459
  1. Remove the 4 stud bolts.



43. REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD


A001166E01
  1. Using a ridge reamer, remove all the carbon from the top of the cylinder.

  1. Push the piston, connecting the rod assembly and upper bearing through the top of the cylinder block to remove them.

    HINT:
    1. Keep the bearing, connecting rod and cap together.
    2. Keep the piston and the connecting rod assemblies in the correct order so that they can be returned to their original locations when reassembled.



44. REMOVE CONNECTING ROD BEARING


45. REMOVE CRANKSHAFT


A037365E02
  1. Using several steps, loosen and remove the 10 bearing cap sub-assembly bolts uniformly using 12 mm socket wrench in the sequence shown in the illustration.

  1. Remove the bearing cap and the crankshaft.



46. REMOVE CRANKSHAFT BEARING


47. REMOVE CRANKSHAFT THRUST WASHER UPPER


48. REMOVE PISTON RING SET

NOTICE:
Keep the piston rings in the correct combination and correct order so that they can be returned to their original locations when re-assembling.



    A037363E01
  1. Using a piston ring expander, remove the 2 compression rings.

  1. Remove the 2 side rails and the oil ring by hand.



49. REMOVE WITH PIN PISTON SUB-ASSEMBLY


A092172E01
  1. Using SST, press the piston pin out of the piston.

    SST
    09221-25026   (09221-00021, 09221-00030, 09221-00090, 09221-00150, 09221-00100)

    NOTICE:
    Keep the pistons, pins, rings, connecting rods and bearings in the correct order so that they can be returned to their original locations when reassembled.



50. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY


51. REMOVE STUD BOLT
  1. Using "Torx" socket wrench E5, remove the 7 stud bolts.



52. REMOVE RING PIN


53. REMOVE STRAIGHT PIN