Home › ENGINE ยท 2NZ-FE › COOLING › WATER PUMP

WATER PUMP > INSTALLATION

for Preparation Click here



1. INSTALL WATER PUMP ASSEMBLY


A116192
  1. Install the water pump assembly through a new gasket with the 3 bolts and 2 nuts.

    Torque:
    11 N*m{ 112 kgf*cm , 8.1 ft.*lbf }



2. INSTALL WATER PUMP PULLEY
  1. Provisionally install the water pump pulley with the 3 bolts.



    A116191E01
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Tighten the 3 bolts to the specified torque.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }



3. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH (for Hatchback)


G100143E01
  1. Install the engine mounting insulator sub-assembly RH with the 5 bolts and nut.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf } for bolt A
    52 N*m{ 530 kgf*cm , 38 ft.*lbf } for bolt B and nut



4. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH (for Sedan)


G100143
  1. Install the engine mounting insulator sub-assembly RH with the 5 bolts and nut.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }



5. INSTALL GENERATOR ASSEMBLY


A115420E01
  1. Provisionally install the generator with fixing bolt B.



    A115419E01
  1. Provisionally install the fan belt adjusting slider with fan belt adjusting slider fixing bolts A and B, then move the generator toward the cylinder block and tighten bolt B.

    Torque:
    11 N*m{ 112 kgf*cm , 8.1 ft.*lbf }



    A115418
  1. Install the connector and wire harness clamp.

  1. Install terminal B with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7.2 ft.*lbf }

  1. Install the terminal cap.

  1. Close the terminal cap.



6. INSTALL FAN & GENERATOR V BELT
  1. Provisionally install the fan and generator V belt onto each pulley.

    NOTICE:
    1. Make sure that there is no foreign matter or liquid, such as oil, on the belt and pulleys.
    2. Make sure that the V belt is securely fitted into the rib grooves of the pulley.



7. ADJUST FAN & GENERATOR V BELT


    A116198E01
  1. for Unleaded Gasoline Specification Vehicle:
    Insert an adjusting bar between the engine mounting bracket and generator assembly. Pull the adjusting bar towards the vehicle front to adjust the generator V belt tension.

    NOTICE:
    Do not insert the adjusting bar between the camshaft timing oil control valve assembly and generator assembly. It could damage the camshaft timing oil control valve assembly.



    A117470
  1. for Leaded Gasoline Specification Vehicle:
    Insert the adjusting bar between the engine mounting bracket and generator assembly. Pull the adjusting bar towards the vehicle front to adjust the generator V belt tension.



    A116197E01
  1. First tighten bolt A, then tighten bolt B.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf } for bolt A
    54 N*m{ 551 kgf*cm , 40 ft.*lbf } for bolt B



8. INSPECT FAN & GENERATOR V BELT


    A116200E01
  1. Check the V belt deflection and tension.

    Deflection:
    Item
    Specified Condition
    New belt
    8.0 to 9.0 mm (0.31 to 0.35 in)
    Used belt
    12.5 to 13.5 mm (0.49 to 0.53 in)

    Tension:
    Item
    Specified Condition
    New belt
    700 to 800 N (71 to 82 kg, 157 to 180 lb)
    Used belt
    300 to 400 N (31 to 41 kg, 67 to 90 lb)

    If the belt deflection is not as specified, adjust it.

    HINT:
    1. Perform the V belt inspection and adjustment while the engine is cold.
    2. V-ribbed belt tension and deflection should be checked immediately after installation of a new belt, and after cranking the engine when inspecting a used belt.
    3. Check the V belt deflection at the point between the specified pulleys where the deflection is greatest.
    4. When installing a new belt, set its tension to the intermediate value of the specification.
    5. When inspecting a belt which has been used for over 5 minutes, apply the Used Belt specifications.
    6. When reinstalling a belt which has been used for over 5 minutes, adjust its deflection and tension to the intermediate values of each Used Belt specification.
    7. V-ribbed belt tension and deflection should be checked after 2 revolutions of engine cranking.
    8. When using a belt tension gauge, confirm its accuracy by using a master gauge first.



9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



10. ADD ENGINE COOLANT
  1. Tighten all the plugs.

  1. Pour engine coolant into the radiator assembly until it overflows.

    Capacity:
    w/o Fan Shroud Ventilation Duct: M/T 4.9 liters (5.2 USqts, 4.6 lmp. qts)
    w/o Fan Shroud Ventilation Duct: A/T 4.8 liters (5.1 USqts, 4.5 lmp. qts)
    w/ Fan Shroud Ventilation Duct: M/T 5.1 liters (5.4 USqts, 4.7 lmp. qts)
    w/ Fan Shroud Ventilation Duct: A/T 5.0 liters (5.3 USqts, 4.6 lmp. qts)

    NOTICE:
    Do not substitute water for engine coolant.

    HINT:
    1. Use of improper engine coolant may damage the engine coolant system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.

  1. Install the radiator cap sub-assembly securely.

  1. Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Manual air conditioning system
      Automatic air conditioning system
      Set control as follows
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Fan speed - Any setting except "OFF"
      Temperature - To the highest temperature
      Air conditioning switch "OFF"
      "AUTO" switch "OFF"

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

  1. Stop the engine and wait until the coolant cools down.

  1. If the engine coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the engine coolant level stays at the full level.

  1. Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add the engine coolant.



11. CHECK FOR ENGINE COOLANT LEAKAGE

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.



    A106594
  1. Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.



12. INSTALL ENGINE UNDER COVER RH

Torque:
5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



13. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY (for Rough Road Area Specification Vehicles)

Torque:
18 N*m{ 184 kgf*cm , 13 ft.*lbf }