Home › BODY ELECTRICAL › LIGHTING › HEADLIGHT DIMMER SWITCH

HEADLIGHT DIMMER SWITCH > INSPECTION

for Preparation Click here



1. INSPECT HEADLIGHT DIMMER SWITCH (for LHD, RHD Europe)


E106610E01
  1. Check the resistance of the light control switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      -
      OFF
      10 kΩ or higher
      10 - 13
      TAIL
      Below 1 Ω
      10 - 13
      HEAD
      Below 1 Ω
      11 - 12
      HEAD
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch.

  1. Check the resistance of the headlight dimmer switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      9 - 11
      FLASH
      Below 1 Ω
      8 - 11
      LOW BEAM
      Below 1 Ω
      9 - 11
      HI BEAM
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch.

  1. Check the resistance of the turn signal switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      6 - 7
      Right turn
      Below 1 Ω
      -
      Neutral
      10 kΩ or higher
      5 - 7
      Left turn
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch.

  1. w/ Front fog light:
    Check the resistance of the front fog light switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      -
      OFF
      10 kΩ or higher
      3 - 4
      Front fog light switch ON
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch.

  1. w/ Rear fog light:
    Check the resistance of the rear fog light switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      -
      OFF
      10 kΩ or higher
      2 - 3 - 4
      Rear fog light switch ON
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch.



2. INSPECT HEADLIGHT DIMMER SWITCH (for RHD except Europe)


E106610E01
  1. Check the resistance of the light control switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      -
      OFF
      10 kΩ or higher
      5 - 8
      TAIL
      Below 1 Ω
      5 - 8
      HEAD
      Below 1 Ω
      6 - 7
      HEAD
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch.

  1. Check the resistance of the headlight dimmer switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      7 - 9
      FLASH
      Below 1 Ω
      7 - 10
      LOW BEAM
      Below 1 Ω
      7 - 9
      HI BEAM
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch.

  1. Check the resistance of the turn signal switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      11 - 13
      Right turn
      Below 1 Ω
      -
      Neutral
      10 kΩ or higher
      11 - 12
      Left turn
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch.

  1. w/ Front fog light:
    Check the resistance of the front fog light switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      -
      OFF
      10 kΩ or higher
      1 - 2
      Front fog light switch ON
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch.

  1. w/ Rear fog light:
    Check the resistance of the rear fog light switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      -
      OFF
      10 kΩ or higher
      1 - 2 - 3
      Rear fog light switch ON
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch.