Home › BODY ELECTRICAL › WIPER AND WASHER › FRONT WIPER MOTOR (for Hatchback)

FRONT WIPER MOTOR (for Hatchback) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT WIPER MOTOR


E113859
  1. Install the front wiper motor with the 3 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Apply DENSO No. 50 grease to the crank arm pivot of the front wiper motor.



    E113860
  1. Install the rod onto the crank arm pivot of the front wiper motor.



2. INSTALL FRONT WIPER MOTOR AND LINK


E113861
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



3. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD)


E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.



4. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


E113854
  1. Connect the washer hose.



    E113852
  1. Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.



    E117641
  1. Engage the 2 hooks and install cowl top ventilator louver center No. 1.



5. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD)


E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.



6. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.



7. INSTALL HOOD TO COWL TOP SEAL


E113851
  1. Engage the 7 clips and install the hood to cowl top seal.



8. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113862E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



9. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113863E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



10. INSTALL FRONT WIPER ARM HEAD CAP


E113849
  1. Engage the claw and install the 2 front wiper arm head caps.