Home › BODY ELECTRICAL › WIPER AND WASHER › WIPER SWITCH (for Hatchback)

WIPER SWITCH (for Hatchback) > INSPECTION

for Preparation Click here



1. INSPECT WIPER SWITCH (for LHD)


E109077E03
  1. Check the resistance.

    1. Measure the resistance and check the results in accordance with the value(s) in the tables below.

      Standard Resistance:
      Front Wiper Switch:
      Tester Connection
      Condition
      Specified Condition
      +B (B-2) - +1 (B-3)
      MIST
      Below 1 Ω
      +S (B-1) - +1 (B-3)
      OFF
      Below 1 Ω
      +S (B-1) - +1 (B-3)
      INT
      Below 1 Ω
      +B (B-2) - +1 (B-3)
      LO
      Below 1 Ω
      +B (B-2) - +2 (B-4)
      HI
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.

      Standard Resistance:
      Front Washer Switch:
      Tester Connection
      Condition
      Specified Condition
      EW (A-2) - WF (A-3)
      OFF
      10 kΩ or higher
      EW (A-2) - WF (A-3)
      ON
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.

      Standard Resistance:
      Rear Wiper and Washer Switch (w/ Intermittent):
      Tester Connection
      Condition
      Specified Condition
      EW (A-2) - WR (B-5)
      WASH (Rear wiper switch OFF)
      Below 1 Ω
      EW (A-2) - WR (B-5)
      EW (A-2) - +1R (A-7)
      EW (A-2) - C1R (A-6)
      OFF
      10 kΩ or higher
      C1R (A-6) - EW (A-2)
      LO
      Below 1 Ω
      EW (A-2) - +1R (A-7)
      HI
      Below 1 Ω
      EW (A-2) - WR (B-5)
      EW (A-2) - +1R (A-7)
      +1R (A-7) - WR (B-5)
      WASH (Rear wiper switch ON)
      Below 1 Ω

      If the result is not as specified, replace the windshield wiper switch.

      Standard Resistance:
      Rear Wiper and Washer Switch (w/o Intermittent):
      Tester Connection
      Condition
      Specified Condition
      EW (A-2) - WR (B-5)
      WASH (Rear wiper switch OFF)
      Below 1 Ω
      EW (A-2) - WR (B-5)
      EW (A-2) - +1R (A-7)
      OFF
      10 kΩ or higher
      EW (A-2) - +1R (A-7)
      ON
      Below 1 Ω
      EW (A-2) - WR (B-5)
      EW (A-2) - +1R (A-7)
      +1R (A-7) - WR (B-5)
      WASH (Rear wiper switch ON)
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.



  1. Check the intermittent operation.

    1. Connect the positive (+) voltmeter terminal to terminal 3 (+1) of the B connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the A connector.

    2. Connect the positive (+) battery lead to terminal 2 (+B) of the B connector and the negative (-) battery lead to terminals 2 (EW) of the A connector and 1 (+S) of the B connector.

    3. Turn the wiper switch to the INT position.

    4. Connect the positive (+) battery lead to terminal 1 (+S) of the B connector for 5 seconds.



    5. Connect the negative (-) battery lead to terminal 1 (+S) of the B connector. Operate the intermittent wiper relay and check the voltage between terminals 3 (+1) of the B connector and 2 (EW) of the A connector.

      Standard:
      Refer to the illustration below.



      E106356E31

      If the result is not as specified, replace the windshield wiper switch.



  1. Check the operation (front washer).

    1. Turn the wiper switch off.

    2. Connect the positive (+) battery lead to terminal 2 (+B) of the B connector and the negative (-) battery lead to terminals 1 (+S) of the B connector and 2 (EW) of the A connector.



    3. Connect the positive (+) voltmeter terminal to terminal 3 (+1) of the B connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the A connector. Turn the washer switch on and off, and check the voltage between terminals 3 (+1) of the B connector and 2 (EW) of the A connector.

      Standard:
      Refer to the illustration below.



      E106382E16

      If the result is not as specified, replace the windshield wiper switch.



2. INSPECT WIPER SWITCH (for RHD)


E114461E05
  1. Check the resistance.

    1. Measure the resistance and check the results in accordance with the value(s) in the tables below.

      Standard Resistance:
      Front Wiper Switch:
      Tester Connection
      Condition
      Specified Condition
      +B (A-3) - +1 (A-2)
      MIST
      Below 1 Ω
      +S (A-4) - +1 (A-2)
      OFF
      Below 1 Ω
      +S (A-4) - +1 (A-2)
      INT
      Below 1 Ω
      +B (A-3) - +1 (A-2)
      LO
      Below 1 Ω
      +B (A-3) - +2 (A-1)
      HI
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.

      Standard Resistance:
      Front Washer Switch:
      Tester Connection
      Condition
      Specified Condition
      EW (B-2) - WF (B-1)
      OFF
      10 kΩ or higher
      EW (B-2) - WF (B-1)
      ON
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.

      Standard Resistance:
      Rear Wiper and Washer Switch:
      Tester Connection
      Condition
      Specified Condition
      EW (B-2) - WR (A-10)
      WASH (Rear wiper switch OFF)
      Below 1 Ω
      EW (B-2) - WR (A-10)
      EW (B-2) - 1R (B-4)
      OFF
      10 kΩ or higher
      EW (B-2) - +1R (B-4)
      ON
      Below 1 Ω
      EW (B-2) - WR (A-10)
      EW (B-2) - +1R (B-4)
      +1R (B-4) - WR (A-10)
      WASH (Rear wiper switch ON)
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.



  1. Check the intermittent operation.

    1. Connect the positive (+) voltmeter terminal to terminal 2 (+1) of the A connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the B connector.

    2. Connect the positive (+) battery lead to terminal 3 (+B) of the A connector and the negative (-) battery lead to terminals 2 (EW) of the B connector and 4 (+S) of the A connector.

    3. Turn the wiper switch to the INT position.

    4. Connect the positive (+) battery lead to terminal 4 (+S) of the A connector for 5 seconds.



    5. Connect the negative (-) battery lead to terminal 4 (+S) of the A connector. Operate the intermittent wiper relay and check the voltage between terminals 2 (+1) of the A connector and 2 (EW) of the B connector.

      Standard:
      Refer to the illustration below.



      E106356E32

      If the result is not as specified, replace the windshield wiper switch.



  1. Check the operation (front washer).

    1. Turn the wiper switch off.

    2. Connect the positive (+) battery lead to terminal 3 (+B) of the A connector and the negative (-) battery lead to terminals 4 (+S) of the A connector and 2 (EW) of the B connector.



    3. Connect the positive (+) voltmeter terminal to terminal 2 (+1) of the A connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the B connector. Turn the washer switch on and off, and check the voltage between terminals 2 (+1) of the A connector and 2 (EW) of the B connector.

      Standard:
      Refer to the illustration below.



      E106382E17

      If the result is not as specified, replace the windshield wiper switch.