Home › ENGINE · 2NZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0724    Brake Switch "B" Circuit High

for Preparation Click here


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling when the brakes are suddenly applied while driving in the lock-up condition. When the brake pedal is depressed, this switch sends signals to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.

DTC No.
DTC Detection Conditions
Trouble Areas
P0724
Stop light switch remains ON even when vehicle repeats 5 cycles of STOP (less than 3 km/h (1.86 mph)) and GO (30 km/h (18.65 mph) or more)
(2 trip detection logic)
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. Stop light control relay*
  4. ECM
  1. *: for Hatchback

WIRING DIAGRAM


A195012E03


A195022E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

  1. Read the value displayed on the tester when the brake pedal is depressed and released.

OK:
Brake Pedal
Display
Released
OFF
Depressed
ON



NG
Go to step 4
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.CHECK STOP LIGHT SWITCH INSTALLATION
  1. Check the stop light switch installation .

    OK:
    Stop light switch is installed correctly.

    Result:
    Result
    Proceed To
    OK (Hatchback)
    A
    OK (Sedan)
    B
    NG
    C



B
Go to step 4

C
SECURELY REINSTALL STOP LIGHT SWITCH
A


3.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Disconnect the stop light control relay connector.

  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

  1. Read the value displayed on the tester when the brake pedal is depressed and released.

    OK:
    Brake Pedal
    Display
    Released
    OFF
    Depressed
    ON

  1. Reconnect the stop light control relay connector.



NG
Go to step 4
OK

REPLACE STOP LIGHT CONTROL RELAY 

4.INSPECT STOP LIGHT SWITCH ASSEMBLY
A195013E01
  1. Remove the stop light switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Position
    Specified Condition
    1 - 2
    Switch pin released
    Below 1 Ω
    Switch pin pushed in
    10 kΩ or higher
    3 - 4
    Switch pin released
    10 kΩ or higher
    Switch pin pushed in
    Below 1 Ω

  1. Reinstall the stop light switch assembly.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)


    A195010E01
  1. Disconnect the ECM connector.

  1. Disconnect the stop light switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A21-36 (STP) - A13-1
    Always
    Below 1 Ω
    A21-35 (ST1-) - A13-4
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A21-36 (STP) or A13-1 - Body ground
    Always
    10 kΩ or higher
    A21-35 (ST1-) or A13-4 - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed To
    OK (Hatchback)
    A
    OK (Sedan)
    B
    NG
    C

  1. Reconnect the ECM connector.

  1. Reconnect the stop light switch connector.



B
REPLACE ECM (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


6.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - STOP LIGHT SWITCH)


    A195019E01
  1. Disconnect the stop light control relay connector.

  1. Disconnect the stop light switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    J55-6 (+B) - A13-2
    Always
    Below 1 Ω
    J55-2 (STP) - A13-1
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    J55-6 (+B) or A13-2 - Body ground
    Always
    10 kΩ or higher
    J55-2 (STP) or A13-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the stop light control relay connector.

  1. Reconnect the stop light switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)