Home › BODY ELECTRICAL › DOOR LOCK › FRONT DOOR LOCK (for Hatchback)

FRONT DOOR LOCK (for Hatchback) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DOOR LOCK ASSEMBLY

NOTICE:
  1. If reusing a door lock that has been removed, replace the packing in the connecting part with new.
  2. Make sure that no grease and dirt adheres to the packing surface in the connecting part.

  1. Apply MP grease to the sliding and rotating areas of the front door lock.



    B121553
  1. Connect the front door lock remote control cable and the front door inside locking cable.



    B121552
  1. Close the cover.



    B116845
  1. Insert the door lock open rod into the front door lock, then set it to the door panel.

    NOTICE:
    Make sure that the outside handle link is securely engaged with the door lock.



    B116836
  1. Apply adhesive to the threads of the screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Using "TORX" socket wrench T30, install the front door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



2. INSTALL FRONT DOOR OUTSIDE HANDLE COVER


B116858
  1. Using "TORX" socket wrench T30, install the cover with the door lock key cylinder.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    Make sure that the door lock key cylinder rod is inserted.

  1. Install the hole plug.



3. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER


B116831
  1. Install the front door frame sub-assembly rear lower with the bolt.

    Torque:
    6.2 N*m{ 63 kgf*cm , 54 in.*lbf }



4. INSTALL FRONT DOOR WEATHERSTRIP


B116833
  1. for 5 Door:
    Engage the 35 clips and install the front door weatherstrip.



    B116834
  1. for 3 Door:
    Engage the 37 clips and install the front door weatherstrip.



5. INSTALL FRONT DOOR CHECK ASSEMBLY


B116830
  1. Apply MP grease to the sliding areas of the door check.

  1. Install the front door check onto the door panel with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the front door check onto the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



6. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/ Power Window)
  1. Apply MP grease to the sliding and rotating areas of the front door window regulator.

    NOTICE:
    Do not apply grease to the window regulator spring.



    B116828E01
  1. Loosely screw bolt A onto the front door window regulator.

  1. Insert the front door window regulator into the door panel. Use bolt A to hang the front door window regulator on the door panel.

    NOTICE:
    Do not drop the window regulator as it may be damaged.

  1. Install the front door window regulator with the 5 bolts, and tighten bolt A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



7. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/o Power Window)
  1. Apply MP grease to the sliding and rotating areas of the front door window regulator sub-assembly.

    NOTICE:
    Do not apply grease to the window regulator spring.



    B116857E01
  1. Loosely screw bolt A onto the front door window regulator sub-assembly.

  1. Insert the front door window regulator into the door panel. Use bolt A to hang the front door window regulator on the door panel.

    NOTICE:
    Do not drop the window regulator as it may be damaged.

  1. Install the front door window regulator with the 4 bolts, and tighten bolt A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



8. INSTALL FRONT DOOR GLASS RUN


B116826
  1. Install the front door glass run.



9. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


B116847
  1. Insert the door glass into the door panel along the glass run as indicated by the arrows in the illustration.

    NOTICE:
    Do not damage the glass.



    B116825
  1. Install the front door glass onto the front door window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



10. INSTALL FRONT DOOR SERVICE HOLE COVER


B116848E01
  1. for 5 Door:
    Apply butyl tape to the door panel, then install the front door service hole cover as shown in the illustration.

    Specification:
    Area
    Dimension
    A
    2.0mm (0.079 in.) or more
    B
    6.0mm (0.236 in.) or more

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.



    B116849E01
  1. for 3 Door:
    Apply butyl tape to the door panel, then install the front door service hole cover as shown in the illustration.

    Specification:
    Area
    Dimension
    A
    2.0mm (0.079 in.) or more
    B
    6.0mm (0.236 in.) or more

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.



11. INSTALL FRONT DOOR BELT MOULDING


    B114401
  1. for 5 Door:

    1. Engage the 5 claws and the clip and install a new front door belt moulding.



    2. B114397E02
    3. Remove the protective tape.



    B114614
  1. for 3 Door:

    1. Engage the 5 claws and the clip and install a new front door belt moulding.



    2. B114612E01
    3. Remove the protective tape.



12. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY


B118045
  1. Engage the claw, then install the outer rear view mirror with the 3 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. w/ Power mirror:
    Connect the connector.



13. INSTALL FRONT DOOR WINDOW FRAME REAR MOULDING (for 3 Door)


    B114606E01
  1. Clean the attachment surface.

    1. Using an infrared light, heat the adhesive remaining on the body.

      NOTICE:
      Do not burn yourself with the heated body or infrared light.

    2. Using a shop rag or piece of cloth, rub the remaining adhesive off the body.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Apply new double-sided adhesive tape to the front door window frame rear moulding.
    Tape size: 
    Area
    t
    W
    H
    A
    0.8 mm (0.032 in.)
    5 mm (0.197 in.)
    340 mm (13.386 in.)
    B
    0.8 mm (0.032 in.)
    5 mm (0.197 in.)
    376 mm (14.803 in.)



    B114607
  1. Engage the 2 clips and the claw and install the front door window frame rear moulding.



14. INSTALL FRONT DOOR WINDOW FRAME FRONT MOULDING


    B127706E01
  1. Clean the attachment surface.

    1. Using an infrared light, heat the adhesive remaining on the body.

      NOTICE:
      Do not burn yourself with the heated body or infrared light.

    2. Using a shop rag or piece of cloth, rub the remaining adhesive off the body.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Apply new double-sided adhesive tape to the front door window frame front moulding.
    Tape size: 
    Area
    t
    W
    H
    A
    1.2 mm (0.047 in.)
    7 mm (0.276 in.)
    88 mm (3.465 in.)



    B127705E01
  1. Engage the 2 clips and the claw and install the front door window frame front moulding.



15. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


B127219
  1. Connect the front door lock remote control cable and front door inside locking cable.



    B116821
  1. 5 Door:
    Engage the 8 clips and install the front door trim board.



    B116822
  1. 3 Door:
    Engage the 9 clips and install the front door trim board.



    B107840
  1. Tighten the 4 screws.



16. INSTALL FRONT ARMREST BASE PANEL UPPER


B116819
  1. Connect the connector.

  1. Engage the 5 claws and clip and install the front armrest base panel upper.



17. INSTALL DOOR ARMREST COVER


B116818
  1. for 5 Door:
    Engage the 8 claws and 3 clips and install the door armrest cover.



    B116851
  1. for 3 Door:
    Engage the 12 claws and 4 clips and install the door armrest cover.



18. INSTALL DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


B116863
  1. Install the window regulator handle plate.

  1. Open all the windows.



    B116947E01
  1. Install the front door window regulator handle with clip at the angle shown in the illustration.



19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }