Home › BODY ELECTRICAL › DOOR LOCK › REAR DOOR LOCK (for Hatchback)

REAR DOOR LOCK (for Hatchback) > INSTALLATION

for Preparation Click here



1. INSTALL REAR DOOR LOCK ASSEMBLY

NOTICE:
  1. If reusing a door lock that has been removed, replace the packing in the connecting part with new.
  2. Make sure that no grease and dirt adheres to the packing surface in the connecting part.

  1. Apply MP grease to the sliding and rotating areas of the front door lock.



    B127211
  1. Connect the rear door lock remote control cable and the rear door inside locking cable.



    B121554
  1. Close the 2 covers.

  1. Insert the door lock into the outside handle frame release plate, then set it onto the door panel.

  1. Make sure that the outside handle frame link is securely engaged with the door lock.

  1. Apply adhesive to the threads of the screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    B116930
  1. Using "TORX" socket wrench T30, install the rear door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/ Power Window)
  1. Apply MP grease to the sliding and rotating areas of the rear door window regulator.

    NOTICE:
    Do not apply grease to the window regulator spring.



    B116928E01
  1. Loosely screw bolt A onto the rear door window regulator.

  1. Insert the rear door window regulator into the door panel. Use bolt A to hang the rear door window regulator on the door panel.

    NOTICE:
    Do not drop the window regulator as it may be damaged.

  1. Install the rear door window regulator with the 4 bolts, and tighten bolt A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



3. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/o Power Window)
  1. Apply MP grease to the sliding and rotating areas of the rear door window regulator.

    NOTICE:
    Do not apply grease to the window regulator spring.

  1. Loosely screw bolt A onto the rear door window regulator.



    B116943E01
  1. Install the rear door window regulator into the door panel. Use bolt A to hang the rear door window regulator on the door panel.

    NOTICE:
    Do not drop the window regulator as it may be damaged.

  1. Install the rear door window regulator with the 2 bolts, and tighten bolt A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


B116927
  1. Install the rear door glass onto the rear door window regulator.



5. INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP
  1. Install the rear door quarter window glass onto the rear door quarter window weatherstrip.



    B116926
  1. Slide the rear door quarter window weatherstrip, in the direction indicated by the arrow in the illustration, to install it.



6. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


B116924
  1. Install the rear door window division bar with the 2 bolts and screw.

    Torque:
    6.2 N*m{ 63 kgf*cm , 54 in.*lbf }



7. INSTALL REAR DOOR GLASS RUN


B116877
  1. Install the rear door glass run.



8. INSTALL REAR DOOR BELT MOULDING


    B114406
  1. Engage the 5 claws and the clip and install a new rear door belt moulding.



    B114404E01
  1. Remove the protective tape.



9. INSTALL REAR DOOR WEATHERSTRIP


B116876
  1. Engage the 32 clips and install the rear door weatherstrip.



10. INSTALL REAR DOOR CHECK ASSEMBLY


B116875
  1. Apply MP grease to the sliding areas of the door check.

  1. Install the rear door check onto the door panel with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the rear door check onto the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



11. INSTALL REAR DOOR SERVICE HOLE COVER


B116873E01
  1. w/ Rear speaker:
    Apply butyl tape to the door panel, then install the rear door service hole cover as shown in the illustration.

    Specification:
    Area
    Dimension
    A
    2.0 mm (0.079 in.) or more
    B
    6.0 mm (0.236 in.) or more

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.



    B116874E01
  1. w/o Rear speaker:
    Apply butyl tape to the door panel, then install the rear door service hole cover as shown in the illustration.

    Specification:
    Area
    Dimension
    A
    2.0 mm (0.079 in.) or more
    B
    6.0 mm (0.236 in.) or more

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.



12. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


B116868
  1. Connect the rear door lock remote control cable and rear door inside locking cable.

  1. Connect the connector.



    B116867
  1. Engage the 7 clips and install the rear door trim board.



    B116866
  1. Tighten the 2 screws.



    B116865
  1. Engage the 3 claws and install the rear door armrest plug.



13. INSTALL DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


B116863
  1. Install the window regulator handle plate.

  1. Open all the windows.



    B121530E01
  1. Install the rear door window regulator handle with the clip at the angle shown in the illustration.



14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }