Home › BODY ELECTRICAL › DOOR LOCK › REAR DOOR LOCK (for Hatchback)

REAR DOOR LOCK (for Hatchback) > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the LH side.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


B116942
  1. Insert a clip remover between the plate and door trim.

  1. Turn the handle with the clip remover inserted, as shown in the illustration.

  1. Remove the rear door window regulator handle assembly and clip.

  1. Remove the window regulator handle plate.



3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


B116864E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the rear door armrest plug.



    B116866
  1. Remove the 2 screws.



    B116867
  1. Disengage the 7 clips.

  1. Disconnect the connector.



    B116868
  1. Disconnect the rear door lock remote control cable and rear door inside locking cable and remove the rear door trim board.



4. REMOVE REAR DOOR SERVICE HOLE COVER


B116871
  1. w/ Rear speaker:
    Disconnect the connectors and clamps, then remove the rear door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.



    B116872
  1. w/o Rear speaker:
    Disconnect the connectors and clamps, then remove the rear door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.



5. REMOVE REAR DOOR CHECK ASSEMBLY


B116875
  1. Remove the 3 bolts, then remove the rear door check.

    NOTICE:
    Do not drop or damage the door check when removing the bolts.

    HINT:
    Remove the door check through the service hole.



6. REMOVE REAR DOOR WEATHERSTRIP


B116876
  1. Disengage the 32 clips and remove the rear door weatherstrip.

    NOTICE:
    Remove any tape remaining on the door side.



7. REMOVE REAR DOOR BELT MOULDING


    B114404E01
  1. Apply protective tape to the door panel in the area around the rear door belt moulding.



    B114405E01
  1. Using a moulding remover, disengage the 5 claws and the clip and remove the rear door belt moulding.



8. REMOVE REAR DOOR GLASS RUN


B116877
  1. Remove the rear door glass run.



9. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


B116924
  1. Remove the 2 bolts and screw and rear door window division bar.

    NOTICE:
    Do not drop or damage the rear door window division bar when removing the bolts and screw.



10. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP


B116925
  1. Slide the rear door quarter window weatherstrip, in the direction indicated by the arrow in the illustration, to remove it.

  1. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.



11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


B116927
  1. Remove the rear door glass from the rear door window regulator.



12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/ Power Window)


B116928E01
  1. Disconnect the connector.

  1. Loosen bolt A.

  1. Remove the 3 bolts, then remove the rear door window regulator.

    NOTICE:
    Do not drop or damage the rear door window regulator when removing the bolts.

    HINT:
    Remove the window regulator through the service hole.



13. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/o Power Window)


B116943E01
  1. Loosen bolt A.

  1. Remove the 2 bolts, then remove the rear door window regulator.

    NOTICE:
    Do not drop or damage the window regulator when removing the 2 bolts.

    HINT:
    Remove the window regulator through the service hole.



14. REMOVE REAR DOOR LOCK ASSEMBLY


B116930
  1. Using "TORX" socket wrench T30, remove the 3 screws.

  1. Move the rear door lock downward, remove the outside handle frame release plate and remove the rear door lock.



    B121554
  1. Open the 2 covers.



    B127211
  1. Disconnect the rear door lock remote control cable and the rear door inside locking cable.

  1. Remove the door lock wire harness seal.