Home › ENGINE ยท 2NZ-FE › COOLING › COOLANT

COOLANT > REPLACEMENT

for Preparation Click here


CAUTION:
Be sure that the ignition is off if you work near the electric cooling fans or radiator grille. With the ignition on the electric cooling fans may automatically start to run if the engine coolant temperature is high and/or the air conditioning is on.



1. DRAIN ENGINE COOLANT

NOTICE:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly.



  1. Loosen the cylinder block drain cock plug, then drain the coolant.


    A106596E01



2. ADD ENGINE COOLANT
  1. Tighten all the plugs.

  1. Pour engine coolant into the radiator assembly until it overflows.

    Capacity:
    w/o Fan Shroud Ventilation Duct: M/T 4.9 liters (5.2 USqts, 4.6 lmp. qts)
    w/o Fan Shroud Ventilation Duct: A/T 4.8 liters (5.1 USqts, 4.5 lmp. qts)
    w/ Fan Shroud Ventilation Duct: M/T 5.1 liters (5.4 USqts, 4.7 lmp. qts)
    w/ Fan Shroud Ventilation Duct: A/T 5.0 liters (5.3 USqts, 4.6 lmp. qts)

    NOTICE:
    Do not substitute water for engine coolant.

    HINT:
    1. Use of improper engine coolant may damage the engine coolant system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.

  1. Install the radiator cap sub-assembly securely.

  1. Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Manual air conditioning system
      Automatic air conditioning system
      Set control as follows
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Fan speed - Any setting except "OFF"
      Temperature - To the highest temperature
      Air conditioning switch "OFF"
      "AUTO" switch "OFF"

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

  1. Stop the engine and wait until the coolant cools down.

  1. If the engine coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the engine coolant level stays at the full level.

  1. Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add the engine coolant.



3. CHECK FOR ENGINE COOLANT LEAKAGE

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.



    A106594
  1. Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.