ENGINE ASSEMBLY > INSTALLATION |
| 1. INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY |
![]() |
Install the drive shaft heat insulator sub-assembly with the bolt and nut.
| 2. INSTALL EXHAUST MANIFOLD |
![]() |
Tighten the exhaust manifold nuts and bolts, in the order shown in the illustration, through a new gasket.
| 3. INSTALL MANIFOLD SUPPORT BRACKET |
Install the manifold bracket with the 3 bolts.
| 4. INSTALL EXHAUST MANIFOLD HEAT INSULATOR NO. 1 |
Install the exhaust manifold insulator with the 3 bolts.
| 5. INSTALL WIRE HARNESS CLAMP BRACKET |
![]() |
Install the 2 wire harness clamp brackets with the 2 bolts.
| 6. INSTALL ENGINE WIRE |
Connect all sensor connectors and wire harness clamps to the engine assembly and install the engine wire harness.
| 7. INSTALL BOOSTER VACUUM TUBE |
![]() |
Install the booster vacuum tube with the 2 bolts.
| 8. INSTALL WATER BY-PASS PIPE NO. 1 |
![]() |
Install water by-pass pipe No. 1 through a new gasket with the 2 bolts and 2 nuts.
| 9. INSTALL INTAKE MANIFOLD |
Install a new gasket onto the intake manifold.
![]() |
Provisionally tighten the intake manifold in the order shown in the illustration, and then tighten it to the specified torque.
Connect the engine wire to the intake manifold.
![]() |
Connect the water by-pass hose to water by-pass pipe No. 1.
![]() |
Connect the water by-pass hose to the cylinder head.
Connect the union to connector tube hose to the booster vacuum tube.
Connect the throttle with motor body assembly connector.
| 10. INSTALL OIL LEVEL GAUGE SUB-ASSEMBLY |
| 11. INSTALL GENERATOR ASSEMBLY |
![]() |
Provisionally install the generator with fixing bolt B.
![]() |
Provisionally install the fan belt adjusting slider with fan belt adjusting slider fixing bolts A and B, then move the generator toward the cylinder block and tighten bolt B.
![]() |
Install the connector and wire harness clamp.
Install terminal B with the nut.
Install the terminal cap.
Close the terminal cap.
| 12. INSTALL IGNITION COIL NO. 1 |
| 13. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transaxle) |
![]() |
Hold the crankshaft with SST.
Clean the 6 bolts and their holes.
![]() |
Apply adhesive to the 2 or 3 end threads of bolts.
Install the drive plate spacer RR, drive plate and ring gear sub-assembly and drive plate spacer FR.
![]() |
Install and uniformly tighten the 6 bolts in several steps, in the sequence shown in the illustration.
| 14. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle) |
![]() |
Make sure that the knock pin is installed on the engine side.
Install the automatic transaxle with torque converter with the 7 bolts.
| 15. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Hold the crankshaft with SST.
Clean the 6 bolts and their holes.
![]() |
Apply adhesive to the 2 or 3 end threads of new bolts.
![]() |
Install the flywheel with the 6 bolts in the order shown in the illustration.
Mark paint marks on the bolt heads in the engine upper side.
![]() |
Tighten the bolts 90° in the sequence order shown in the illustration.
| 16. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle) |
![]() |
Insert SST into the clutch disc assembly, then insert them both into the flywheel sub-assembly.
| 17. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle) |
![]() |
Align the matchmark on the clutch cover assembly with that on the flywheel sub-assembly.
Following the procedures shown in the illustration, tighten the 6 bolts in order, starting with the bolt located near the knock pin at the top.
| 18. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transaxle) |
![]() |
Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.
![]() |
If the alignment is not as specified, using SST, adjust the diaphragm spring tip alignment.
| 19. INSTALL MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle) |
![]() |
Align the input shaft with the clutch disc and install the manual transaxle onto the engine.
Install the 7 bolts.
| 20. INSTALL CONTROL CABLE BRACKET (for Manual Transaxle) |
![]() |
Install the control cable bracket with the 2 bolts.
| 21. INSTALL STARTER ASSEMBLY |
![]() |
Install the starter assembly with the 2 bolts.
Connect the connector.
Connect terminal 30 with the nut.
Close the terminal cap.
| 22. INSTALL FLYWHEEL HOUSING SIDE COVER |
![]() |
Insert the protruding portion into the end of the cylinder block and while pushing it along the cylinder block, fit the claw into the cylinder block.
| 23. CONNECT HEATER WATER HOSE INLET A |
Connect heater water inlet hose A to the cylinder head.
| 24. INSTALL WATER FILLER SUB-ASSEMBLY |
Connect radiator hose No. 1 to the cylinder head.
Install the water filler sub-assembly with 2 nuts.
Connect radiator hose No. 1 to the water filler.
| 25. INSTALL FUEL TUBE SUB-ASSEMBLY |
![]() |
Connect the fuel tube connector and fuel pipe and install fuel pipe clamp No. 2.
| 26. INSTALL VENTILATION HOSE NO. 2 |
Install ventilation hose No. 2 with the clip.
| 27. INSTALL VENTILATION HOSE |
Install the ventilation hose with the clip.
| 28. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
Install the engine moving control rod with the through bolt.
Remove the 2 bolts and remove the 2 engine hangers.
Install the oxygen sensor wiring bracket with the bolt.
Install the radio setting condenser with the bolt.
| 29. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE (for Hatchback) |
![]() |
Set the engine assembly with transaxle and front suspension crossmember on the engine lifter.
Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember to the position where the engine mounting insulator RH and LH can be installed.
![]() |
Install the engine mounting insulator LH with the through bolt and nut.
![]() |
Install the engine mounting insulator RH with the 5 bolts and nut.
![]() |
Operate the engine lifter and provisionally install the engine assembly with transaxle and front suspension crossmember onto the vehicle with the 6 bolts.
Insert SST into the datum holes in the front suspension crossmember RH and LH alternately and tighten bolts A, B and C on both sides in several sequences.

| 30. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE (for Sedan) |
![]() |
Set the engine assembly with transaxle and front suspension crossmember on the engine lifter.
Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember to the position where the engine mounting insulator RH and LH can be installed.
![]() |
Install the engine mounting insulator LH with the through bolt and nut.
![]() |
Install the engine mounting insulator RH with the 5 bolts and nut.
![]() |
Operate the engine lifter and provisionally install the engine assembly with transaxle and front suspension crossmember onto the vehicle with the 6 bolts.
Insert SST into the datum holes in the front suspension crossmember RH and LH alternately and tighten bolts A, B and C on both sides in several sequences.

| 31. INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transaxle) |
![]() |
Tighten the 6 torque converter set bolts.
| 32. INSTALL FLYWHEEL HOUSING UNDER COVER |
| 33. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH |
for Automatic Transaxle:
Coat the spline of the inboard joint with ATF.
for Manual Transaxle:
Coat the spline of the inboard joint with gear oil.
![]() |
Align the inboard joint splines and install the drive shaft with a screwdriver and hammer.
| 34. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH |
| 35. INSTALL AUTOMATIC TRANSMISSION CASE PROTECTOR (w/o ABS) |
![]() |
Install the transmission case protector with the 2 bolts.
| 36. INSTALL FRONT AXLE ASSEMBLY LH |
Push the front axle out of the vehicle to align the spline of the drive shaft with the front axle and insert the front axle.
| 37. INSTALL FRONT AXLE ASSEMBLY RH |
| 38. INSTALL FRONT STABILIZER LINK ASSEMBLY LH |
![]() |
Install the stabilizer link with the nut.
| 39. INSTALL FRONT STABILIZER LINK ASSEMBLY RH |
| 40. INSTALL FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO. 1 LH |
![]() |
Install the lower arm onto the steering knuckle with a new castle nut.
Install a new clip.
| 41. INSTALL FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO. 1 RH |
| 42. INSTALL TIE ROD END SUB-ASSEMBLY LH |
![]() |
Install the tie rod end onto the steering knuckle with a new castle nut.
Install a new cotter pin.
| 43. INSTALL TIE ROD END SUB-ASSEMBLY RH |
| 44. INSTALL SPEED SENSOR FRONT LH (w/ ABS) |
![]() |
Install the speed sensor onto the steering knuckle with the bolt.
![]() |
Install the flexible hose and speed sensor with the bolt.
| 45. INSTALL SPEED SENSOR FRONT RH (w/ ABS) |
| 46. INSTALL FRONT FLEXIBLE HOSE LH (w/o ABS) |
![]() |
Install the flexible hose with the bolt.
| 47. INSTALL FRONT FLEXIBLE HOSE RH (w/o ABS) |
| 48. INSTALL FRONT AXLE SHAFT LH NUT |
![]() |
Using a 30 mm socket wrench, install a new axle hub nut.
Using a chisel and hammer, stake the axle hub nut.
| 49. INSTALL FRONT AXLE SHAFT RH NUT |
| 50. INSTALL EXHAUST PIPE ASSEMBLY FRONT (for Unleaded Gasoline Specification Vehicle) |
![]() |
Using vernier calipers, measure the free length of the compression spring.
![]() |
Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.
Install the 3 No. 4 exhaust pipe supports.
Install the exhaust front pipe assembly and a new exhaust pipe gasket with the 4 compression springs and 4 bolts.

| 51. INSTALL EXHAUST PIPE ASSEMBLY FRONT (for Leaded Gasoline Specification Vehicle) |
![]() |
Using vernier calipers, measure the free length of the compression spring.
![]() |
Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.
Install the 3 No. 4 exhaust pipe supports.
Install the exhaust front pipe assembly and a new exhaust pipe gasket with the 4 compression springs and 4 bolts.

| 52. INSTALL OXYGEN NO. 2 SENSOR (for Unleaded Gasoline Specification Vehicle) |
![]() |
Using SST, install the sensor onto the front exhaust pipe.
Pass the sensor connector through the floor panel and install the grommet.
Connect the sensor connector.
| 53. INSTALL CONSOLE BOX ASSEMBLY REAR (for Hatchback) |
![]() |
Engage the 2 clips and install the console box with the bolt.
| 54. INSTALL CONSOLE BOX COVER REAR (for Hatchback) |
![]() |
Engage the 8 claws to install the console box rear cover.
| 55. INSTALL SHIFTING HOLE COVER SUB-ASSEMBLY (for Hatchback) |
![]() |
Engage the 6 claws and install the shifting hole cover.
| 56. INSTALL REAR CONSOLE BOX ASSEMBLY (for Sedan) |
| 57. INSTALL CONSOLE BOX CARPET (for Sedan) |
| 58. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Sedan) |
| 59. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY (for Sedan) |
| 60. INSTALL INSTRUMENT PAD LOWER LH (for Sedan) |
| 61. INSTALL INSTRUMENT PANEL FINISH PANEL END LH (for Sedan) |
| 62. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER (for Sedan) |
| 63. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle) |
| 64. INSTALL STEERING COLUMN HOLE COVER SUB-ASSEMBLY NO. 1 |
![]() |
Install clip B onto the body portion and install No. 1 steering column hole cover onto the body portion with clip A.
| *1 | Clip A |
| *2 | Clip B |
| 65. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY |
![]() |
Align the matchmarks and install the sliding yoke onto the intermediate shaft with bolt B.
| *1 | Bolt A |
| *2 | Bolt B |
| *a | Matchmark |
Tighten bolt A.
| 66. INSTALL COLUMN HOLE COVER SILENCER SHEET |
Install the column hole cover silencer sheet with the 2 clips.
Install the floor carpet.
| 67. CONNECT ENGINE WIRE |
Install the transaxle earth wire of the transaxle engine room wire harness with the bolt.
![]() |
Connect the 2 engine wire harness connectors and wire harness clamp to the engine room junction block.
![]() |
Connect the engine wire harness connector to the ECM.
| 68. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle) |
![]() |
Install the clutch release cylinder and clutch pipe with the 4 bolts.
| 69. INSTALL WITH PULLEY COMPRESSOR ASSEMBLY (w/ Air Conditioning System) |
![]() |
Provisionally tighten the compressor with the bolt.
![]() |
Tighten the compressor with the 4 bolts.
Connect the connector and the clamp.
| 70. INSTALL FAN & GENERATOR V BELT |
Provisionally install the fan and generator V belt onto each pulley.
| 71. ADJUST FAN & GENERATOR V BELT |
![]() |
for Unleaded Gasoline Specification Vehicle:
Insert an adjusting bar between the engine mounting bracket and generator assembly. Pull the adjusting bar towards the vehicle front to adjust the generator V belt tension.
![]() |
for Leaded Gasoline Specification Vehicle:
Insert the adjusting bar between the engine mounting bracket and generator assembly. Pull the adjusting bar towards the vehicle front to adjust the generator V belt tension.
![]() |
First tighten bolt A, then tighten bolt B.
| 72. CONNECT FUEL TUBE SUB-ASSEMBLY |
![]() |
Connect the fuel tube connector and fuel pipe, and install fuel pipe clamp No. 1.
| 73. CONNECT HEATER WATER HOSE INLET A |
![]() |
Connect heater water inlet hose A to the heater unit.
| 74. CONNECT HEATER WATER OUTLET HOSE A (FROM HEATER UNIT) |
![]() |
Connect heater water outlet hose A to the heater unit.
| 75. CONNECT UNION TO CHECK VALVE HOSE |
Connect the union to check valve hose to the booster vacuum tube.
| 76. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle) |
![]() |
Install the transmission control cable onto the control shaft lever with the nut.
Install the transmission control cable into the bracket with the new clip.
| 77. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle) |
![]() |
Connect the 2 cable ends and install the 2 washers and the 2 clips.
Install 2 new clips onto the control cable bracket.
| 78. INSTALL CYLINDER HEAD COVER NO. 2 |
![]() |
Tighten 2 A nuts, then 2 B nuts.
| 79. CONNECT OIL COOLER OUTLET HOSE (for Automatic Transaxle) |
![]() |
Connect the oil cooler outlet hose with the clip.
| 80. CONNECT OIL COOLER INLET HOSE (for Automatic Transaxle) |
![]() |
Connect the oil cooler inlet hose with the clip.
| 81. CONNECT RADIATOR HOSE NO. 2 |
![]() |
Connect radiator hose No. 2 to the water inlet.
| 82. CONNECT RADIATOR RESERVOIR TANK HOSE |
![]() |
Connect the radiator reservoir tank hose to the water filler.
| 83. CONNECT RADIATOR HOSE NO. 3 |
![]() |
Connect radiator hose No. 3 to the water filler.
| 84. INSTALL BATTERY CARRIER |
![]() |
Install the battery carrier with the 5 bolts.
Install the clamp.
| 85. INSTALL AIR CLEANER BRACKET |
![]() |
Install the air cleaner bracket with the 2 bolts.
Connect the wire harness clamp to the air cleaner bracket.
| 86. INSTALL AIR CLEANER ASSEMBLY |
![]() |
Install the air cleaner case with air cleaner inlet No. 1 with the 2 bolts.
Connect the wire harness to the air cleaner case.
Install the air cleaner element.
![]() |
Install and lock the air cleaner cap and air cleaner hose and then tighten the air cleaner hose clamp.
Connect the ventilation hose to the air cleaner hose.
Connect the vacuum switching valve connector and wire harness clamp.
Connect the fuel vapor feed hose and fuel vapor feed hose No. 1 to the vacuum switching valve assembly.
Connect the intake air flow meter connector and wire harness clamp.
| 87. INSTALL COWL TOP PANEL OUTER (for Hatchback) |
![]() |
Install the cowl top panel with the 9 bolts.
![]() |
Connect the wire harness clamp.
| 88. INSTALL COWL TOP PANEL OUTER (for Sedan) |
![]() |
Install the cowl top panel outer with the 8 bolts.
![]() |
Install the cowl top to cowl inner brace with the 2 bolts.
![]() |
Connect the wire harness clamp.
| 89. INSTALL COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2 (for Hatchback) |
![]() |
Engage the claw to install cowl to register duct No. 2.
| 90. INSTALL FRONT WIPER MOTOR AND LINK (for Hatchback) |
![]() |
Connect the connector.
Slide the wiper link as shown in the illustration and engage the rubber pin with the body.
Install the front wiper motor and link with the 2 bolts.
| 91. INSTALL FRONT WIPER MOTOR AND LINK (for Sedan) |
![]() |
Connect the connector.
Slide the wiper link as shown in the illustration and engage the rubber pin with the body.
Install the front wiper motor and link with the 2 bolts.
| 92. INSTALL FRONT AIR SHUTTER SEAL (for Sedan) |
![]() |
Engage the 3 claws to install the front air shutter seal.
| 93. INSTALL COWL TOP VENTILATOR LOUVER LH (for Hatchback LHD) |
![]() |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the 2 clips.
| 94. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Hatchback LHD) |
![]() |
Connect the washer hose.
![]() |
Engage the 11 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
![]() |
Engage the 2 hooks and install cowl top ventilator louver center No. 1.
| 95. INSTALL COWL TOP VENTILATOR LOUVER LH (for Hatchback RHD) |
![]() |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the clip.
| 96. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Hatchback RHD) |
![]() |
Engage the 10 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
| 97. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan LHD) |
![]() |
Connect the washer hoses.
Engage the 5 hooks.
![]() |
Engage the 8 hooks and the 4 claws.
Install the cowl top ventilator louver sub-assembly with the 3 clips.
| 98. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan RHD) |
![]() |
Connect the washer hoses.
Engage the 5 hooks.
![]() |
Engage the 10 hooks and the 6 claws.
Install the cowl top ventilator louver sub-assembly with the 2 clips.
| 99. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH (for Sedan) |
![]() |
Engage the 3 claws and install the cowl side ventilator sub-assembly LH.
| 100. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH (for Sedan) |
| 101. INSTALL HOOD TO COWL TOP SEAL (for Hatchback) |
![]() |
Engage the 7 clips and install the hood to cowl top seal.
| 102. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH (for Hatchback) |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 103. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH (for Sedan) |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 104. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (for Hatchback) |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 105. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (for Sedan) |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
| 106. INSTALL FRONT WIPER ARM HEAD CAP (for Hatchback) |
![]() |
Engage the claw and install the 2 front wiper arm head caps.
| 107. INSTALL FRONT WIPER ARM HEAD CAP (for Sedan) |
![]() |
Engage the claw and install the 2 front wiper arm head caps.
| 108. INSTALL BATTERY TRAY |
| 109. INSTALL BATTERY |
Install the battery onto the vehicle with the battery clamp.
Connect the cable to the battery terminal.
| 110. ADD ENGINE COOLANT |
Tighten all the plugs.
Pour engine coolant into the radiator assembly until it overflows.
Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.
Install the radiator cap sub-assembly securely.
Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.
Warm up the engine until the cooling fan operates.
Set the air conditioning as follows while warming up the engine.
| Item | Manual air conditioning system | Automatic air conditioning system |
| Set control as follows | Fan speed - Any setting except "OFF" Temperature - Toward WARM Air conditioning switch "OFF" | Fan speed - Any setting except "OFF" Temperature - To the highest temperature Air conditioning switch "OFF" "AUTO" switch "OFF" |
Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.
Stop the engine and wait until the coolant cools down.
If the engine coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the engine coolant level stays at the full level.
Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add the engine coolant.
| 111. ADD AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle) |
| Drain and refill | 2.5 liters (2.6 US qts, 2.2 Imp. qts) |
| Dry fill | 5.6 liters (5.9 US qts, 4.9 Imp. qts) |
| 112. INSPECT AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle) |
![]() |
Park the vehicle on a level surface and engage the parking brake.
With the engine idling and the brake pedal depressed, shift the shift lever into all positions from P to L, and then return it to the P position.
Pull out the oil level gauge and wipe it clean.
Push it fully back into the pipe.
Pull it out and check that the fluid level is within the HOT range.
If there is any leakage, repair or replace O-rings, FIPGs, oil seals, plugs or other parts.
| 113. ADD MANUAL TRANSAXLE OIL (for Manual Transaxle) |
| 114. INSPECT MANUAL TRANSAXLE OIL (for Manual Transaxle) |
![]() |
Stop the vehicle in a level place.
Remove the transmission filler plug and the gasket.
Check that the oil surface is within 5 mm (0.20 in.) of the bottom of the transmission filler plug opening.
Check for oil leakage when the oil level is low.
Install the transmission filler plug and a new gasket.
| 115. INSPECT FAN & GENERATOR V BELT |
![]() |
Check the V belt deflection and tension.
| Item | Specified Condition |
| New belt | 8.0 to 9.0 mm (0.31 to 0.35 in) |
| Used belt | 12.5 to 13.5 mm (0.49 to 0.53 in) |
| Item | Specified Condition |
| New belt | 700 to 800 N (71 to 82 kg, 157 to 180 lb) |
| Used belt | 300 to 400 N (31 to 41 kg, 67 to 90 lb) |
| 116. CHECK FOR FUEL LEAKAGE |
When using the intelligent tester.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and intelligent tester main switch on.
Select the Active Test mode on the intelligent tester.
Check that there is no fuel leakage anywhere on the fuel system after doing maintenance.
| 117. CHECK FOR ENGINE OIL LEAKAGE |
| 118. CHECK FOR EXHAUST GAS LEAKAGE |
| 119. CHECK FOR ENGINE COOLANT LEAKAGE |
![]() |
Fill the radiator assembly with engine coolant, then attach a radiator cap tester.
Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
| 120. INSTALL ENGINE UNDER COVER RH |
| 121. INSTALL ENGINE UNDER COVER LH |
| 122. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY (for Rough Road Area Specification Vehicles) |
| 123. INSTALL FRONT WHEELS |
| 124. INSPECT IGNITION TIMING |
When using an intelligent tester:
Warm up and stop the engine.
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Select the following menu items:
Powertrain / Engine and ECT / Active Test / TC (TE1) / ON.
Inspect the ignition timing during idling.
Select the following menu items: TC (TE1) / OFF
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
When not using an intelligent tester:
Remove cylinder head cover No. 2 .
![]() |
Pull out the wire harness (brown) shown in the illustration.
Warm up and stop the engine.
Connect the clip of the timing light to the wire harness.
Turn the ignition switch on (IG).
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Inspect the ignition timing during idling.
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the ignition switch off.
Remove the timing light.
Install the cylinder head cover No. 2 .
| 125. INSPECT ENGINE IDLING SPEED |
When using an intelligent tester:
Warm up and stop the engine.
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Select the following menu items: Powertrain / Engine and ECT /Data List / Engine Speed.
Inspect the engine idling speed.
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
When not using an intelligent tester.
Warm up and stop the engine.
![]() |
Install SST to terminal 9 (TAC) of the DLC3, then connect a tachometer.
Turn the ignition switch on (IG).
Inspect the engine idling speed.
Turn the ignition switch off.
Disconnect the tachometer.
Remove SST from terminal 9 (TAC).
| 126. INSPECT CO/HC |
Start the engine.
Run the engine at 2,500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe while idling.
Check the CO/HC concentration during idling and when running at 2,500 rpm.
for Unleaded Gasoline specification Vehicle:
Check the heated oxygen sensor operation (Click here ).
See the table below for possible causes, then inspect the applicable parts and repair them if necessary.
| CO | HC | Problems | Possible Causes |
| Normal | High | Rough idling |
|
| Low | High | Rough idling (Fluctuating HC reading) |
|
| High | High | Rough idling (Black smoke from exhaust) |
|
| 127. INSPECT FRONT WHEEL ALIGNMENT |
| 128. INSPECT ABS SENSOR SIGNAL (w/ ABS) |