Home › ENGINE ยท 2NZ-FE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE


2. REMOVE BATTERY
  1. Disconnect the cable from the battery terminal.

  1. Loosen the nut and remove the battery clamp.

  1. Remove the battery.



3. REMOVE BATTERY TRAY


4. REMOVE FRONT WHEELS


5. REMOVE ENGINE UNDER COVER LH


6. REMOVE ENGINE UNDER COVER RH


7. REMOVE ENGINE UNDER COVER SUB-ASSEMBLY (for Rough Road Area Specification Vehicles)


8. DRAIN ENGINE COOLANT

NOTICE:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly.



  1. Loosen the cylinder block drain cock plug, then drain the coolant.


    A106596E01



9. DRAIN AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle)
  1. Remove the drain plug and gasket, and drain the ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    17 N*m{ 175 kgf*cm , 13 ft.*lbf }



10. DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)
  1. Remove the filler plug and the gasket.

  1. Remove the drain plug and gasket, and then drain the manual transaxle oil.

  1. Install a new gasket and the drain plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



11. REMOVE FRONT WIPER ARM HEAD CAP (for Hatchback)


E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.



12. REMOVE FRONT WIPER ARM HEAD CAP (for Sedan)


    E127832E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.



13. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH (for Hatchback)
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113850
  1. Remove the nut and front wiper arm.



14. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH (for Sedan)


    E127833
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. Remove the nut and front wiper arm.



15. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH (for Hatchback)

HINT:
Use the same procedure as for the LH side.



16. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH (for Sedan)

HINT:
Use the same procedure as for the LH side.



17. REMOVE HOOD TO COWL TOP SEAL (for Hatchback)


E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.



18. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH (for Sedan)


    E127834E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.



19. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH (for Sedan)

HINT:
Use the same procedure as for the LH side.



20. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Hatchback LHD)


E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.



    E113852
  1. Disconnect the washer hose.

  1. Disengage the 11 claws and clip.



    E113854
  1. Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.



21. REMOVE COWL TOP VENTILATOR LOUVER LH (for Hatchback LHD)


E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.



22. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Hatchback RHD)


E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.



23. REMOVE COWL TOP VENTILATOR LOUVER LH (for Hatchback RHD)


E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.



24. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan LHD)


    E127838
  1. Disengage the 3 clips, the 4 claws and the 8 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.



    E127839
  1. Disconnect the washer hoses.

  1. Disengage the 5 hooks.



25. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan RHD)


    E127835
  1. Disengage the 2 clips, the 6 claws and the 10 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.



    E127836
  1. Disconnect the washer hoses.

  1. Disengage the 5 hooks.



26. REMOVE FRONT WIPER MOTOR AND LINK (for Hatchback)


E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.



27. REMOVE FRONT WIPER MOTOR AND LINK (for Sedan)


    E127837
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.



28. REMOVE COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2 (for Hatchback)


A108437
  1. Disengage the claw and remove cowl to register duct sub-assembly No. 2.



29. REMOVE FRONT AIR SHUTTER SEAL (for Sedan)


A133324
  1. Disengage the 3 claws and remove the front air shutter seal.



30. REMOVE COWL TOP PANEL OUTER (for Hatchback)


A108438
  1. Disengage the wire harness clamp.



    A115392
  1. Remove the 9 bolts and remove the cowl top panel outer.



31. REMOVE COWL TOP PANEL OUTER (for Sedan)


A128446
  1. Disengage the wire harness clamp.



    A128447
  1. Remove the 2 bolts and remove the cowl top to cowl inner brace.



    A128448
  1. Remove the 8 bolts and remove the cowl top panel outer.



32. REMOVE AIR CLEANER ASSEMBLY


A117355
  1. Separate the intake air flow meter connector and wire harness clamp.

  1. Separate the fuel vapor feed hose and fuel vapor feed hose No. 1 from the vacuum switching valve assembly.

  1. Separate the vacuum switching valve connector and wire harness clamp.

  1. Separate the ventilation hose from the air cleaner hose.

  1. Release the air cleaner cap sub-assembly with air cleaner hose No. 1.

  1. Loosen the air cleaner hose clamp on the throttle body side and remove the air cleaner cap and air cleaner hose.

  1. Remove the air cleaner element.



    A104895
  1. Separate the wire harness clamp from the air cleaner case.

  1. Remove the 2 bolts and remove the air cleaner case with air cleaner inlet No. 1.



33. REMOVE AIR CLEANER BRACKET


A117308
  1. Separate the wire harness clamp from the air cleaner bracket.

  1. Remove the 2 bolts and remove the air cleaner bracket.



34. REMOVE BATTERY CARRIER


A117309
  1. Separate the wire harness clamp from the battery carrier.

  1. Remove the 5 bolts and remove the battery carrier.



35. DISCONNECT RADIATOR HOSE NO. 3


A117310
  1. Disconnect radiator hose No. 3 from the water filler.



36. DISCONNECT RADIATOR RESERVOIR TANK HOSE


A117356
  1. Disconnect the radiator reservoir tank hose from the water filler.



37. DISCONNECT RADIATOR HOSE NO. 2


A104893
  1. Disconnect radiator hose No. 2 from the water inlet.



38. DISCONNECT OIL COOLER INLET HOSE (for Automatic Transaxle)


A117306
  1. Loosen the clip and disconnect the oil cooler inlet hose.



39. DISCONNECT OIL COOLER OUTLET HOSE (for Automatic Transaxle)


A117307
  1. Loosen the clip and disconnect the oil cooler outlet hose.



40. REMOVE CYLINDER HEAD COVER NO. 2


A116235
  1. Remove the 4 nuts and cylinder head cover No. 2.



41. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle)


C107765
  1. Remove the nut and disconnect the control cable from the control shaft lever.

  1. Remove the clip and disconnect the control cable from the control cable bracket.



42. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)


C115305
  1. Remove the 2 clips and the 2 washers, and disconnect the 2 cables from the transaxle.

  1. Remove the 2 clips and disconnect the 2 cables from the control cable bracket.



43. DISCONNECT UNION TO CHECK VALVE HOSE
  1. Disconnect the union to check valve hose from the booster vacuum tube.



44. DISCONNECT HEATER WATER OUTLET HOSE A (FROM HEATER UNIT)


I100777
  1. Disconnect heater water outlet hose A from the heater unit.



45. DISCONNECT HEATER WATER HOSE INLET A


I100779
  1. Disconnect heater water inlet hose A from the heater unit.



46. DISCONNECT FUEL TUBE SUB-ASSEMBLY


A105667
  1. Remove fuel pipe clamp No. 1.



    A117321
  1. Pinch the retainer as illustrated, then pull the fuel tube connector out of the pipe.

    NOTICE:
    1. Remove any dirt and foreign matter from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting, as the fuel tube connector has the O-rings that seal the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected parts by covering them with vinyl bags after disconnecting the fuel tube.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.



47. REMOVE FAN & GENERATOR V BELT


    A116197E01
  1. Loosen bolts A and B.

  1. Release the fan and generator V belt tension and remove the fan and generator V belt.



48. SEPARATE WITH PULLEY COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
  1. Disconnect the connector.

  1. Remove the 4 bolts and separate the with pulley compressor assembly.

    HINT:
    Remove the compressor assembly together with the low and high pressure hoses, then suspend them from the body with a piece of rope.



49. SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle)


C106371
  1. Remove the 4 bolts, then separate the clutch release cylinder.

    HINT:
    Suspend the clutch release cylinder with a piece of rope so as not to overload the clutch pipe.



50. DISCONNECT ENGINE WIRE


A107314
  1. Pull up the lever and disconnect the connector of the engine control computer.



    A104339
  1. Remove the 2 connectors and clamp from the engine room junction block and disconnect the wire harness.

  1. Remove the bolt and separate the transaxle earth wire of the engine room wire harness.

  1. Disconnect all the wire harnesses and connectors. Make sure that no wire harness is connected between the body and engine.



51. REMOVE COLUMN HOLE COVER SILENCER SHEET


    A116501E01
  1. Remove the floor carpet and 2 clips and remove the column hole cover silencer.



52. SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY


    C117212
  1. Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.



    C118005E08
  1. Place matchmarks on the sliding yoke of the steering intermediate shaft assembly and the steering gear assembly.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *a
    Matchmark

  1. Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.



53. SEPARATE STEERING COLUMN HOLE COVER SUB-ASSEMBLY NO. 1


    C139112E02
  1. Remove clip A, separate clip B from the body and separate No. 1 steering column hole cover.
    Text in Illustration 
    *1
    Clip A
    *2
    Clip B

    NOTICE:
    Do not damage clip B.



54. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


55. REMOVE SHIFTING HOLE COVER SUB-ASSEMBLY (for Hatchback)


56. REMOVE CONSOLE BOX COVER REAR (for Hatchback)


C109006E01
  1. Disengage the 8 claws and remove the console box rear cover.



57. REMOVE CONSOLE BOX ASSEMBLY REAR (for Hatchback)


C116873
  1. Remove the bolt and disengage the 2 clips to remove the console box.



58. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER (for Sedan)


59. REMOVE INSTRUMENT PANEL FINISH PANEL END LH (for Sedan)


60. REMOVE INSTRUMENT PAD LOWER LH (for Sedan)


61. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY (for Sedan)


62. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Sedan)


63. REMOVE CONSOLE BOX CARPET (for Sedan)


64. REMOVE REAR CONSOLE BOX ASSEMBLY (for Sedan)


65. REMOVE OXYGEN NO. 2 SENSOR (for Unleaded Gasoline Specification Vehicle)
  1. Disconnect the sensor connector.

  1. Remove the grommet and pass the sensor connector out of the cabin through the floor panel.



    A115424E01
  1. Using SST, remove the heated oxygen No. 2 sensor.

    SST
    09224-00010  



66. REMOVE EXHAUST PIPE ASSEMBLY FRONT
  1. Remove the 2 bolts and 2 springs and separate the exhaust tail pipe assembly.

  1. Remove the 2 bolts and 2 springs and separate the exhaust manifold.

  1. Remove the 3 exhaust pipe supports and remove the exhaust pipe assembly front.



67. REMOVE FRONT AXLE SHAFT LH NUT


C085629E02
  1. Using SST and a hammer, release the staked part of the axle hub nut.

    SST
    09930-00010  

    NOTICE:
    1. Insert SST into the groove with the flat surface facing up.
    2. Do not damage the tip of SST using grinders.
    3. Completely unstake the staked part before removing the axle hub nut.
    4. Do not damage the threads of the drive shaft.

  1. Using a 30 mm socket wrench, remove the axle hub nut.



68. REMOVE FRONT AXLE SHAFT RH NUT

HINT:
Use the same procedure as for the LH side.



69. SEPARATE SPEED SENSOR FRONT LH (w/ ABS)


C125274
  1. Remove the bolt and separate the speed sensor and flexible hose.



    C112274
  1. Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Keep the speed sensor tip and installation portion free of foreign matter.
    2. Remove the speed sensor without turning it from its original installation angle.



70. SEPARATE SPEED SENSOR FRONT RH (w/ ABS)

HINT:
Use the same procedure as for the LH side.



71. SEPARATE FRONT FLEXIBLE HOSE LH (w/o ABS)


C186418
  1. Remove the bolt and separate the flexible hose.



72. SEPARATE FRONT FLEXIBLE HOSE RH (w/o ABS)

HINT:
Use the same procedure as for the LH side.



73. SEPARATE TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.



    C172757E01
  1. Install SST (spacer B) to the threaded section of the tie rod end.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure the upper ends of the threaded section of the tie rod end and SST (spacer B) are aligned.



  1. Using SST, separate the tie rod end from the front axle assembly.


    C172758E01

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    2. Install SST so that A and B are parallel.
    3. Be sure to place the wrench on the part indicated in the illustration.
    4. Do not damage the ball joint dust cover.
    5. Do not damage the front disc brake dust cover.



74. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



75. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH


C106044
  1. Remove the nut and separate the stabilizer link from the shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.



76. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



77. SEPARATE FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO. 1 LH


C107513
  1. Remove the clip and castle nut.



    C172759E01
  1. Install SST (spacer B) to the threaded section of the lower ball joint.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure the upper ends of the threaded section of the lower ball joint and SST (spacer B) are aligned.



  1. Using SST, separate the front lower suspension arm from the front axle assembly.


    C172760E01

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    2. Install SST so that A and B are parallel.
    3. Be sure to place the wrench on the part indicated in the illustration.
    4. Do not damage the lower ball joint dust cover.
    5. Do not damage the drive shaft outboard joint boots.
    6. Do not damage the front disc brake dust cover.



78. SEPARATE FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO. 1 RH

HINT:
Use the same procedure as for the LH side.



79. SEPARATE FRONT AXLE ASSEMBLY LH
  1. Using a plastic hammer, tap the end of the drive shaft and disengage the fitting between the drive shaft and front axle.

    HINT:
    If it is difficult to disengage the fitting, tap the end of the drive shaft with a brass bar and hammer.

  1. Push the front axle out of the vehicle to remove the drive shaft from the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Do not damage the speed sensor rotor.
    4. Suspend the drive shaft with a piece of string or the equivalent.



80. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



81. REMOVE AUTOMATIC TRANSMISSION CASE PROTECTOR (w/o ABS)


    C121812
  1. Remove the 2 bolts and automatic transmission case protector.



82. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


C107924
  1. Using SST, remove the drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.



83. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH


C116896
  1. Using a screwdriver and hammer, remove the drive shaft.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.



84. REMOVE FLYWHEEL HOUSING UNDER COVER (for Automatic Transaxle)


85. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transaxle)


A117323
  1. Remove the 6 torque converter set bolts.



86. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE


G100156
  1. Set the engine lifter.



    G100143
  1. Remove the 5 bolts and nut and remove the engine mounting insulator RH.



    G100158
  1. Remove the through bolt and nut and separate the engine mounting insulator LH.



    G100157
  1. Remove the 6 bolts, and remove the engine assembly with transaxle and front suspension crossmember from the vehicle.



87. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
  1. Remove the bolt and remove the radio setting condenser.

  1. Remove the bolt and remove the oxygen sensor wiring bracket.



    A070012E01
  1. Install the engine hangers with the bolts, as shown in the illustration.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    Part No.:
    12281-21010 for engine hanger
    91642-81025 for bolt

  1. Using an engine sling device and chain block, suspend the engine assembly with transaxle and front suspension crossmember.

  1. Remove the through bolt from the engine moving control rod and remove the front suspension crossmember.



88. REMOVE VENTILATION HOSE
  1. Loosen the 2 clips and remove the ventilation hose.



89. REMOVE VENTILATION HOSE NO. 2
  1. Loosen the clips and remove ventilation hose No. 2.



90. REMOVE FUEL TUBE SUB-ASSEMBLY


A107342
  1. Disengage the claw and remove fuel pipe clamp No. 2.



    A107343
  1. Pinch the fuel tube connector retainer from both sides, disconnect the fuel tube connector and separate the fuel tube from the pipe.

    NOTICE:
    1. Remove any dirt and foreign matter from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting, as the fuel tube connector has the O-rings that seal the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected parts by covering them with vinyl bags after disconnecting the fuel tube.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.



91. REMOVE WATER FILLER SUB-ASSEMBLY
  1. Disconnect radiator hose No. 1 from the cylinder head.

  1. Remove the 2 nuts and remove the water filler sub-assembly.



92. REMOVE HEATER WATER HOSE INLET A
  1. Disconnect heater water inlet hose A from the cylinder head.



93. REMOVE FLYWHEEL HOUSING SIDE COVER


A104497E01
  1. Disengage the claw by pushing it upward and remove the flywheel housing side cover.



94. REMOVE STARTER ASSEMBLY


A104498
  1. Remove the terminal cap.

  1. Remove the nut and disconnect terminal 30.

  1. Disconnect the connector.

  1. Remove the 2 bolts and remove the starter assembly.



95. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle)


    C118504
  1. Remove the 7 bolts and remove the automatic transaxle with torque converter.



96. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transaxle)


    A117376E01
  1. Hold the crankshaft with SST.

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 6 bolts, drive plate spacer FR, drive plate and ring gear sub-assembly and drive plate spacer RR.



97. REMOVE CONTROL CABLE BRACKET (for Manual Transaxle)


C106374
  1. Remove the 2 bolts and the control cable bracket.



98. REMOVE MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)


C063143
  1. Remove the 7 bolts and the manual transaxle.



99. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transaxle)


D025280E04
  1. Align the matchmark on the clutch cover assembly with the one on the flywheel.

  1. Loosen each set bolt one turn at a time until the spring tension is released.

  1. Remove the set bolts and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.



100. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)


101. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)


    A117376E01
  1. Hold the crankshaft with SST.

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 6 bolts and flywheel.



102. REMOVE OIL LEVEL GAUGE SUB-ASSEMBLY


103. REMOVE IGNITION COIL NO. 1
  1. Disconnect the connectors of the ignition coils.

  1. Remove the bolt and remove all the ignition coils.



104. REMOVE GENERATOR ASSEMBLY


A115418
  1. Remove the terminal cap.

  1. Separate the connector and harness clamp.

  1. Remove the nut and remove terminal B.



    A115419E01
  1. Remove fan belt adjusting slider fixing bolts A and B and remove the fan belt adjusting slider.



    A115420E01
  1. Remove fixing bolt B and remove the generator.



105. REMOVE INTAKE MANIFOLD


A117312
  1. Disconnect the union to connector tube hose from the booster vacuum tube.

  1. Disconnect the engine wire from the intake manifold.



    A117313
  1. Disconnect the water by-pass hose from the cylinder head.



    A117314
  1. Disconnect the water by-pass hose from water by-pass pipe No. 1.

  1. Disconnect the throttle with motor body assembly connector.



    A035213E01
  1. Remove the 3 bolts and 2 nuts in the order shown in the illustration and remove the intake manifold.

  1. Remove the gasket from the intake manifold.



106. REMOVE WATER BY-PASS PIPE NO. 1


A117315
  1. Remove the 2 bolts and 2 nuts and remove water by-pass pipe No. 1.



107. REMOVE BOOSTER VACUUM TUBE


A117316
  1. Remove the 2 bolts and remove the booster vacuum tube.



108. REMOVE ENGINE WIRE
  1. Disconnect all sensor connectors and wire harness clamps from the engine assembly and remove the engine wire harness.



109. REMOVE WIRE HARNESS CLAMP BRACKET


A107284
  1. Remove the 2 bolts and remove the 2 wire harness clamp brackets.



110. REMOVE EXHAUST MANIFOLD HEAT INSULATOR NO.1
  1. Remove the 3 bolts and remove the exhaust manifold heat insulator.



111. REMOVE MANIFOLD SUPPORT BRACKET
  1. Remove the 3 bolts and remove the manifold support bracket.



112. REMOVE EXHAUST MANIFOLD
  1. Remove the 3 bolts and 2 nuts and remove the exhaust manifold.



113. REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY


A117317
  1. Remove the bolt and nut and remove the drive shaft heat insulator.