Home › BRAKE › BRAKE › FRONT BRAKE FLEXIBLE HOSE (for Hatchback)

FRONT BRAKE FLEXIBLE HOSE (for Hatchback) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT BRAKE FLEXIBLE HOSE


C116889E01
  1. Install the flexible hose with the union bolt and a new gasket.

    Torque:
    30 N*m{ 310 kgf*cm , 22 ft.*lbf }

    HINT:
    Install the flexible hose lock securely into the lock hole in the disc brake cylinder.

  1. Install the flexible hose and speed sensor with the bolt.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Install the flexible hose and speed sensor without twisting them.

  1. Install a new clip.

  1. Using SST, install the brake tube.

    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.



2. FILL RESERVOIR WITH BRAKE FLUID


C116908E01
  1. LHD:

    1. Disengage the 3 clips and separate the hood to cowl top seal.

    2. Remove the cowl top ventilator louver.

  1. RHD:

    1. Disengage the 2 clips and separate the hood to cowl top seal.

    2. Remove the cowl top ventilator louver.



    C116909E01
  1. Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4



3. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.



    C116910E02
  1. Using a union nut wrench (10 mm), disconnect the brake tubes from the master cylinder.



    C116911E01
  1. Slowly depress the brake pedal and hold it there (Step A).



    C116912E01
  1. Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.



    C116910E02
  1. Using a union nut wrench (10 mm), connect the brake tubes to the master cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }



4. BLEED BRAKE LINE


C116913
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    Front Disc and Rear Drum Brake:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
    Rear Disc Brake:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



5. BLEED BRAKE ACTUATOR (w/ VSC)

NOTICE:
After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, perform air bleeding of the brake actuator with the intelligent tester by following the procedure below.

  1. Depress the brake pedal more than 20 times with the engine off.

  1. Connect the intelligent tester to the DLC3, and turn the ignition switch to ON.

    NOTICE:
    Do not start the engine.

  1. Select "Air Bleeding" on the intelligent tester.

    HINT:
    Refer to the tester operator's manual for further details.



  1. Bleed the air out of the brake line when Step 1:
    Increase appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty.




      C116913
    1. Connect the vinyl tube to either one of the bleeder plugs.

    2. Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step E).

    3. When fluid stops coming out, tighten the bleeder plug and release the brake pedal (Step F).

    4. Repeat Steps E and F until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug completely.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf } for Front Brake
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf } for Rear Brake

    6. Repeat the above procedure for each wheel to bleed the air out of the brake line.

  1. Bleed the air out of the suction line when Step 2:
    Inhalation appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect the vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.

    2. Operate the brake actuator to bleed the air using the intelligent tester (Step G).

      NOTICE:
      Release the brake pedal at this time.

      HINT:
      This operation stops automatically after 4 seconds.

    3. Check if the operation has stopped by referring to the intelligent tester display and tighten the bleeder plug (Step H).

    4. Repeat Steps G and H until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf } for Front Brake
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf } for Rear Brake

    6. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

  1. Bleed the air out of the pressure reduction line when Step 3: Decrease appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect a vinyl tube to either one of the bleeder plugs.

    2. Loosen the bleeder plug (Step I).

    3. Using the intelligent tester, operate the brake actuator assembly, completely depress the brake pedal and hold it there (Step J).

      NOTICE:
      1. During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
      2. Hold the brake pedal depressed. Do not depress and release the pedal repeatedly.

      HINT:
      1. The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.
      2. When the operation is complete, the brake pedal goes down slightly. This is a normal phenomenon caused when the solenoid opens.

    4. Tighten the bleeder plug, and then release the brake pedal (Step K).

    5. Repeat Steps I to K until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf } for Front Brake
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf } for Rear Brake

    7. Repeat the above procedure for the other wheels to bleed the air out of the brake line.



  1. Bleed the air out of the brake line again when Step 4: Increase appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty.




      C116913
    1. Connect the vinyl tube to either one of the bleeder plugs.

    2. Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step L).

    3. When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step M).

    4. Repeat Steps L and M until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf } for Front Brake
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf } for Rear Brake

    6. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

    7. Make sure that the air bleeding is complete by referring to the intelligent tester display and turn off the intelligent tester.

    8. Disconnect the intelligent tester from the DLC3.

    9. Turn the ignition switch off.



6. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4



7. CHECK FOR BRAKE FLUID LEAKAGE


8. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }