Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › FRONT PASSENGER AIRBAG ASSEMBLY (for Sedan)

FRONT PASSENGER AIRBAG ASSEMBLY (for Sedan) > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.



2. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER


B132316
  1. Disengage the 2 claws and 2 clips and remove the instrument panel finish panel lower center.



3. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


B132317
  1. Disengage the 6 claws and 3 clips and remove the instrument panel finish panel end LH.



4. REMOVE INSTRUMENT PANEL FINISH PANEL END RH


B132318
  1. Disengage the 6 claws and 3 clips and remove the instrument panel finish panel end RH.



5. REMOVE INSTRUMENT CLUSTER FINISH PANEL NO.1


E116832
  1. Disengage the 4 claws and 5 clips and remove the instrument cluster finish panel.



6. REMOVE COMBINATION METER ASSEMBLY


E116819
  1. Disconnect the 2 connectors.

  1. Remove the 2 screws and pull the combination meter rearward to remove it.



7. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Separate the front door opening trim weatherstrip.



8. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Separate the front door opening trim weatherstrip.



9. REMOVE FRONT PILLAR GARNISH RH


    B134777E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B134779
  1. w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B134787
  1. Disconnect the antenna connector.

  1. Using a clip remover, remove the 3 clamps.



    B138437E01
  1. w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

      Protective cover size:
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)



10. REMOVE FRONT PILLAR GARNISH LH


    B134778E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B134780
  1. w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B134789
  1. Using a clip remover, remove the 4 clamps.



    B138438E01
  1. w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

      Protective cover size:
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)



11. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


B132319E01
  1. Disengage the claw and separate the glove compartment door stopper from the glove compartment door.

  1. Slightly flex the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door until it becomes horizontal.



    B132320E01
  1. Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door.

    NOTICE:
    Pull the glove compartment door out horizontally, otherwise, installation failure caused by excessive play around the hinge portion will result.



12. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY


B132322E01
  1. Slide the slider and disconnect the passenger airbag connector.

  1. Disconnect the clamp.



  1. Remove the 2 <C> bolts and 2 <B> screws.


    B132323E01



  1. Disengage the 7 clips by lifting the rear side of the instrument panel up.


    B132324

  1. While lifting the instrument panel, slide it toward the rear of the vehicle. Disengage the 5 claws from the front side of the instrument panel and remove the instrument panel.



13. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY


    B108295E01
  1. Remove the wire harness from the 2 claws of the instrument panel.

  1. Disengage the 10 hooks and remove the instrument panel passenger airbag.



14. REMOVE INSTRUMENT PANEL WIRE ASSEMBLY


    B108296E01
  1. Using a thin-bladed screwdriver, release the locking button.

  1. Using a thin-bladed screwdriver, disconnect the airbag connector and remove the instrument panel wire.